Related Manuals for Ingersoll-Rand FA2i
Summary of Contents for Ingersoll-Rand FA2i
- Page 1 Product Information FORCE 5i Air Winch Models FA2i and FA2i-CE (-CE Compliant With European Directives) Save These Instructions Form MHD56436 Edition 7 February 2016 45899788 2016 Ingersoll Rand ©...
-
Page 2: Product Description
Only allow trained technicians to perform maintenance on this product. For additional information contact factory or nearest Ingersoll Rand Ingersoll Rand Distributor. For additional supporting documentation refer to Table 1 ‘Product Information Manuals’ on page 2. Manuals can be downloaded from ingersollrandproducts.com The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased performance and increased maintenance and will invalidate all warranties. -
Page 3: Specifications
SPECIFICATIONS Model Code Explanation Example: FA2i–24MK320P FA2i Series (Capacity): FA2i 4,400 lbs (2,000 kg) Drum Length (Distance between drum flanges): Standard (Refer to Table 4 ‘Available Drum Lengths’ on page 4. Drum Brake: Automatic Drum Brake Manual Drum Brake None... -
Page 4: Installation
Force at One Capscrew inch inch inch inch inch FA2i & 1.25 10.75 1,825 9,120 FA2i-CE M1 – Material Traceability certificates according to EN 10204 (Ex DIN 50049) 2.2 on Sound measurements have been made in accordance with ISO 11201, ISO 3744-3746 and ISO 4871 test specifications for sound from pneumatic equipment. -
Page 5: Air Supply
Always follow wire rope manufacturer’s recommendation on use and Models inch maintenance of wire rope. FA2i & FA2i-CE Wire Rope Spooling Table 7: Bolt Hole Dimensions To compensate for uneven spooling and the decrease in line pull capacity as the drum fills up, use as short a wire rope as practical. -
Page 6: Operation
CAUTION NOTICE • Lubricator must be located no more than 10 ft (3 m) from motor. • Settings for limit switch are for an overwound operation only. • Shut off air supply before filling air line lubricator. To adjust set points: Follow instructions in the order they appear for limit switch adjustment (use two The air line lubricator should be replenished daily and set to provide 2 to 3 drops per minute of ISO VG 32 (SAE 10W) oil. - Page 7 Do not release locking pin until load control is established. Overload System (FA2i-CE Models only) To disengage Drum Locking Pin: When facing the handle, pull handle away from the outboard upright and pivot it The winch utilizes a direct acting load limiter to limit the maximum line pull to 160% to the right.
-
Page 8: Frequent Inspection
NOTICE WARNING • The full extent of wire rope wear cannot be determined by visual inspection. • All new or repaired equipment should be inspected and tested by At any indication of wear inspect wire rope in accordance with instructions Ingersoll Rand trained Service Technicians to ensure safe operation at in “Periodic Inspection.”... -
Page 9: General Lubrication
Grade Type quarts litres ounces litres ° ° ISO VG 32 (SAE 10W) Below 32 F (0 FA2i & FA2i-CE 1-1/2 4 to 6 ° ° ° ° to 80 F (0 to 27 ISO VG 68 (SAE 20W) * Seals and Bearings °... - Page 10 PRODUCT INFORMATION GRAPHICS Air Out Regulator DRUM Air In Lubricator (Dwg. MHP0133) Filter (Dwg. MHP0191) (Dwg. MHP2772) (Dwg. MHP2686) Lift Slider Handle UP to Unlock Haul-In Payout (Dwg. MHP2688) (Dwg. MHP3099) Form MHD56436 Edition 7...
- Page 11 PRODUCT INFORMATION GRAPHICS (CONTINUED) Twist Red Button to Reset (Dwg. MHP2558) (Dwg. MHP2398) Push In Turn in a counterclockwise direction to reset Emergency Stop. (Dwg. MHP1348) “Emergency Stop” Button (Dwg. MHP2557) “ON” Button Function Levers Pendant Handle (Dwg. MHP1892) Form MHD56436 Edition 7...
- Page 12 PRODUCT INFORMATION GRAPHICS (CONTINUED) Fill Plug Level Plug Drain Plug (Dwg. MHP0222) Fill Plug Drum Position Reduction Gear Assembly Level Plug Position Inboard Upright (Dwg. MHP0140) Form MHD56436 Edition 7...
-
Page 13: Service Notes
SERVICE NOTES Form MHD56436 Edition 7... - Page 14 SERVICE NOTES Form MHD56436 Edition 7...
- Page 15 (SL) Pod polno odgovornostjo izjavljamo, da je izdelek: Pnevmatsko dvigalo (SV) Intygar enligt vårt ansvar att produkten: Tryckluftsdrivna lyftdon Model: FA2i-CE / Serial Number Range: A023737 and up (CS) Model: / Rozsah výrobních čísel: (DA) Model: / Serienummerområde: (DE) Modell: / Seriennummernbereich: (EL) Μοντέλο: / Κλίμακα σειριακών...
- Page 16 ingersollrandproducts.com...
Need help?
Do you have a question about the FA2i and is the answer not in the manual?
Questions and answers
Air flow requirement of FA5i and FA 2i
The air flow requirement for the Ingersoll-Rand FA2i is 8 m³/min (280 ft³/min), and for the FA5i it is 20 m³/min (700 ft³/min).
This answer is automatically generated