Advertisement
INSTALLATION INSTRUCTIONS
Lights sold separately
shown for reference only
PRODUCT SAFETY & LEGAL DISCLAIMER
IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO
•
MAY CAUSE PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY.
Review the product package and contents prior to beginning the installation. Take care when
•
opening the packaging and removing items. If a return is needed you will want to return the product in
its original packaging if possible.
This instruction guide is provided as a GENERAL installation guide, some vehicles vary dimensionally
•
and may require additional steps.
Test fit the product on the vehicle prior to any third party modifications and or finishing. The
•
manufacturer and/or distributors do not accept responsibility for third party charges, labor and or
third part replacement modifications. Some modifications may void the factory warranty.
•
Exercise due-diligence when installing this product. The manufacturer and distributors of this product
do not accept any responsibility for vehicle damage or personal injury resulting from the installation of
this product. Careless installation and operation can result in serious injury or equipment damage.
•
This product is for general off-road use. All liability for installation and use rests with the
owner/operator.
INSTALLER: Once installation is complete, please return this guide along with other documentation
•
included in this product back to the consumer for future reference. The manufacturer/distributors of
this product do not guarantee this particular version will be available at a later date.
REV.01
© 2016 Go Rhino Products. All rights reserved
www.gorhino.com
589 W. Apollo St., Brea, CA 92821
PART NO.
911600T / 911600PS
•
915600T / 915600PS
•
PRODUCT DESCRIPTION:
Full size Sport Bar with Powered Light Bar
•
Mid size Sport Bar with Powered Light Bar
•
P: 888 427 4466
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Go Rhino 911600T
Summary of Contents for Go Rhino 911600T
- Page 1 The manufacturer/distributors of this product do not guarantee this particular version will be available at a later date. © 2016 Go Rhino Products. All rights reserved www.gorhino.com 589 W. Apollo St., Brea, CA 92821 P: 888 427 4466 REV.01...
-
Page 2: Installation Instructions
Installation of some of these products may alter the factory sensor system performance. • Factory sensors may read shackles or hooks protruding from the fairlead and or tow hooks. • All sensor testing is completed by Go Rhino Products and or third party testing labs on modified • vehicles. •... - Page 3 INSTALLATION INSTRUCTIONS PARTS INCLUDED IN THIS LIST: Go Rhino recommends you, the installer, read this installation instruction manual from front to back before installing the product. You may also click here to view an installation video or visit http://www.gorhino.com/Installation-Videos. TOOLS NEEDED FOR INSTALLATION: 5/32”...
- Page 4 ” flat washers, (2) Τ ” lock washers Τ and (2) Τ ” x 1 Τ ” hex bolts, per side. • Do not fully tighten bolts, leave loose for final adjustments. REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 5 • Do not install items 11 and 12, cover plates, if a bed cover is going to be used. • Do not fully tighten bolts, leave loose for final adjustments. REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 6 ” flat washer, (5) Τ ” lock washer and (5) ” x Τ ” button head bolts, per side. Τ • Tighten screws to 70 in/lbs Max. DO NOT OVERTIGHTEN SCREWS REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 7 • Optional wiring for accessory lights. • Be sure to use an adequate relay that corresponds to your system if required. When installing multiple lights, fusing should be adjusted to match. • To actuator REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 8 INSTALLATION INSTRUCTIONS STEP # 5 • Run wire harness through tube. • Use cable ties to keep all lighting wires in place. REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 9 • Remove sport bar and drill 17/32” holes through bed rails. • If holes can not be drill through top and bottom of bed rail proceed to step #7. REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 10 • Hold spacer with ¾” wrench. • Tighten bolt with 9/16” wrench or socket and ratchet, this will compress the rivet nut. • Once tight, unscrew the bolt and rivet nut will be installed. REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 11 ” flat head bolts, per side. • Tighten all front and rear tube bolts to 26 ft/lbs Max. DO NOT OVERTIGHTEN BOLTS • Check and retighten all nuts and bolts periodically. REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 12 STOP • Before operating actuator double check all connections. Improper connection may damage actuator. • Beware of sharp edges, abrasive surfaces and heat sources when routing wires. REV.01 © 2016 Go Rhino Products. All rights reserved...
- Page 13 II-Bar down • Switch may be left in position I or II, which will keep indicator LED on. • In order to turn off indicator LED, move switch to neutral position. REV.01 © 2016 Go Rhino Products. All rights reserved...
-
Page 14: Limited Warranty
This warranty covers the cost of the product only and does not include the cost of removal, installation, third party modifications or shipping of the product. In no event shall Go Rhino be liable to buyer or any third party for any damage or harm caused by the product or use thereof, regardless of weather such damages were foreseeable and whether or not Go Rhino has been advised of the possibility of such damages, not withstanding the failure of any agreed or other remedy of its essential purpose.
Need help?
Do you have a question about the 911600T and is the answer not in the manual?
Questions and answers