No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
It should be free of marks and scratches and in perfect working order upon receipt. As you unpack the PCE-5133/5033, check it for signs of shipping damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or your local sales representative immediately.
Page 6
Figure 2.1 Case Open Jumper Locations........23 Table 2.3: Case Open Mode Jumper ........23 Figure 2.2 Case Open Warning in BIOS Menu ......24 2.13 Serial ATA Interface (SATA0~1 SATA4~7 (PCE-5133), SATA 4~7 (PCE- 5033))...................... 24 Chapter AMI BIOS Setup.........
Page 7
Introduction ..................... 76 Installation ....................76 Chapter Intel USB 3.2........77 Introduction ..................... 78 Chapter 10 SATA RAID Setup ......79 10.1 Introduction ..................... 80 10.2 SATA RAID Driver and Utility Setup ............80 Appendix A Programming the Watchdog Timer..81 PCE-5133/5033 User Manual...
Page 8
Table B.18:1 MB Memory Map ........... 93 B.19 PCI Bus Map................... 94 Table B.19:PCI Bus Map ............94 Appendix C Programming the GPIO ....95 Supported GPIO Register ............... 96 GPIO Registers ..................96 GPIO Example Program-1 ..............96 PCE-5133/5033 User Manual viii...
Introduction PCE-5133/5033 is a PICMG 1.3 form-factor single host board which is designed with Intel® R680E(PCE-5133), and H610E(PCE-5033) PCH for industrial applications that need high computing power and diverse I/O capabilities. PCE-5133/5033 sup- ports 10nm manufacturing technology, LGA1700 socket Intel® Core™ i9/i7/i5/i3, Pentium®...
USB port: Supports 6 x USB 2.0 ports with transfer rates up to 480 Mbps. (2 ports are on the CPU card and 4 ports are on the backplane), and PCE-5133 supports up to 6 USB 3.2 (Gen1) ports with transfer rates of up to 5 Gbps, 2 USB 3.2 (Gen2), and PCE-5033 supports 4x USB3.2 (Gen1).
Supports single/dual 10/100/1000/2500 Mbps Ethernet port(s) via the dedicated PCI Express x1 bus which provides 500 MB/s data transmission rate. Controller: – LAN 1: I226LM(PCE-5133); I226V(PCE-5033) – LAN 2: I226LM(PCE-5133); I226V(PCE-5033) 1.3.6 Industrial Features Watchdog timer: Can generate a system reset. The watchdog timer is pro- ...
Jumpers and Connectors Connectors on the PCE-5133/5033 single host board link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure the system for your application.
FAN x 2 256M-bit USB3 Pin Header For Board TPM Pin Header HDAUD for TPM module PCA-AUDIO-HDB1E HDAUD Pin Header USB 2.0 H/W Monitor USB 2.0 x 1 NCT7802Y USB2 Rear Panel Type A Figure 1.3 PCE-5133 Block Diagram PCE-5133/5033 User Manual...
Caution! There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open or heat the battery. Replace the battery only with the same or equivalent type recommended by the man- ufacturer. Discard used batteries according to the manufacturer’s instructions. PCE-5133/5033 User Manual...
1-2 closed. This procedure will reset the CMOS/ME to its last status or default setting. Table 1.3: JCMOS1/JME1: Clear CMOS/ME Data Function Jumper Setting *Keep BIOS CMOS/ME data 1-2 closed Clear BIOS CMOS/ME data 2-3 closed * default setting PCE-5133/5033 User Manual...
OBS beep (8-10) * default setting System Memory PCE-5133/5033 has two 288-pin memory sockets for (ECC/non ECC) DDR5 4800MHz (Depends on CPU) memory modules with maximum capacity of 64GB. (Maximum 32GB for each DIMM). PCE-5133 supports ECC and non-ECC DDR5 U-DIMM memory modules.
To install a processor, first turn off your system. The PCE-5133/5033 is designed for Intel® LGA 1700 socket processors. Pull the off cover of CPU socket up. Lift the bar beside the processor socket outward and lift it.
Page 20
Lift the CPU socket retainer. Align the cuts on the processor with the edges of the socket. PCE-5133/5033 User Manual...
Processor Cooler Installation Purchasing PCE-5133/5033 optimized CPU cooler (P/N: 1970005349T000) from Advantech is a must. Other brand CPU coolers are NOT compatible with PCE-5133/ 5033. Advantech specially designed CPU cooler and CPU plate is for better heat dis- sipation efficiency and for enhancing rigidity of the CPU card (neither is it compatible with Intel boxed CPU cooler).
Page 22
CPU cooler into the steel back-plate on PCB. Note the direction of CPU cooler, which must follow that shown above. Installing a CPU cooler in the wrong direction may cause poor heat dissipation that may damage the CPU card. PCE-5133/5033 User Manual...
COM expansion (eSPI1) ePSI eSPI is used for the optional expansion of eSPI COM232/485 module developed by Advantech. Please refer to data sheet for respective part numbers. Note! Keep the default settings if an eSPI-interface COM module is not installed, as changing them will prevent the system from turning on.
The IRQ and address ranges for both ports are fixed. However, if you want to disable the port or change these parameters later, you can do this in the system BIOS setup. Please refer to data sheet for optional 1 & 2-port COM cable. PCE-5133/5033 User Manual...
CPU and system fan connectors can support both PWM and DC FAN. System fan connector can support one system fan. system FAN1 CPU FAN1 Front Panel Connectors (JFP1, JFP2 & JFP3) There are several external switches to monitor and control the PCE-5133/5033. PCE-5133/5033 User Manual...
PWR_LED & Key Lock 2.7.2 External Speaker (JFP2) JFP2 is a 4-pin connector for an external speaker. The PCE-5133/5033 provides an onboard buzzer as an alternative to an external speaker. To enable the buzzer, set pins 3 and 4 as closed.
LED1 LED2 1000Mbps Link On Green On 1000Mbps Active Green on Flash 1000Mbps Link Off 100Mbps Link On Orange On 100Mbps Active Orange On Flash 100Mbps Link Off 10Mbps Link On 10Mbps Active Flash 10Mbps Link Off PCE-5133/5033 User Manual...
2.10 High Definition Audio Module Interface (HDAUD1) HDAUD1 This HDAUD1 pin header is the connection interface to Advantech's high definition audio module. Note! Advantech high definition audio module ordering information. P/N: PCA-AUDIO-HDB1E. 2.11 GPIO Header (GPIO1) Provides 10-pin header connector for 8-bit Digital I/O usage. Refer to Appendix B for detailed information on the pin assignments and programming guide in Appendix C.
Page 31
The 2-pin case open connector is for chassis with a case open sensor. When the case is open, the buzzer on motherboard will beep. Table 2.3: Case Open Mode Jumper Case open mode/JCASE1 JCASEOP_SW1 Normally Open(N.O.) 2-3 pin short Normally Closed(N.C.) 1-2 pin short PCE-5133/5033 User Manual...
SATA4-7 SATA0-1 The PCE-5133/5033 features high performance serial ATA interface (6*600MB/s (PCE-5133)/ 4*600MB/s (PCE-5033)) which eases cabling to hard drivers or CD/ DVD drivers with long cables. These six on-board SATA ports can be configured as RAID 0, 1, 10, or 5 (PCE-5033 does not support RAID). Please see the detailed BIOS setting instructions for this in Chapter 3.
The Setup program uses a number of menus for making changes and turning the special features on or off. This chapter describes the basic navigation of the PCE-5133/5033 setup screens. Figure 3.1 Setup Program Initial Screen Entering Setup Turn on the computer and the BIOS is activated as well.
Set the Date. Use Tab to switch between Date elements. Default Ranges: Year: 1998-9999; Months: 1-12; Days: Dependent on month. Range of Years may vary. System Time Sets the Time. Use Tab to switch between Time elements. Power Type This item corresponds with your power supply type. PCE-5133/5033 User Manual...
3.2.2 Advanced BIOS Features Setup Select the Advanced tab from the PCE-5133/5033 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can dis- play an Advanced BIOS Setup option by highlighting it using the <Arrow>...
Page 37
Network Stack Settings. CSM Configuration CSM configuration: Enable/Disable, Option ROM execution settings, etc. NVMe NVMe Device Options Settings. Intel® Rapid Storage Technology Manage RAID volumes Driver Health Health status of drivers/ controllers PCE-5133/5033 User Manual...
Page 38
0 - ~ Hot Plug 1 - SHPC Native Hot Plug control 2 - ~ Power Management Events 3 - PCIe Advanced Error Reporting control 4 - PCIe Capability Structure control 5 - Latency Tolerance Reporting control PCE-5133/5033 User Manual...
Page 39
Number of P-cores to enable in each processor package. Active Efficient-cores Number of E-cores to enable in each processor package. Hyper - Threading Enable or Disable Hyper-Threading Technology. AES: Enable/Disable AES (Advanced Encryption Standard). PCE-5133/5033 User Manual...
Page 40
3.2.2.3 Power & Performance Figure 3.6 Power & Performance CPU - Power Management Control CPU - Power Management Control Options. PCE-5133/5033 User Manual...
Page 41
3.2.2.4 PCH-FW Configuration Figure 3.7 PCH-FW Configuration AMT Configuration Configure Intel(R) Active Management Technology Parameters. Firmware Update Configuration Configure Management Engine Technology Parameters. PTT configuration Configure PTT PCE-5133/5033 User Manual...
Page 43
Select to Tell OS to support PPI spec Version 1.2 or 1.3. TPM 2.0 InterfaceType Select to support TPM 1.2, TPM 2.0 or Auto. Auto will support both TPM 1.2 and TPM 2.0 3.2.2.7 ACPI Setting Figure 3.10 ACPI Settings PCE-5133/5033 User Manual...
Page 44
Enable Deep Sleep to cut off the power of peripherals in sleep state to comply with EU ErP (Energy-related Product) regulations, please enable this function and C states function. (Path: Advanced --> Power & Performance --> CPU - Power Management --> C State --> Enable PCE-5133/5033 User Manual...
Page 45
3.2.2.8 Smart Settings Figure 3.12 Smart Settings Figure 3.13 Smart Settings SMART Self Test Run SMART Self Test on all HDDs during POST. PCE-5133/5033 User Manual...
Page 46
3.2.2.9 Super I/O Configuration Figure 3.14 Super IO Configuration Figure 3.15 Super IO Configuration PCE-5133/5033 User Manual...
Page 47
Figure 3.16 Serial Port 1 Configuration Figure 3.17 Serial Port 1 Configuration PCE-5133/5033 User Manual...
Page 48
Figure 3.18 Serial Port 2 Configuration Figure 3.19 Serial Port 2 Configuration Serial Port 1 Configuration Sets Parameters of Serial Port 1(COMA). Serial Port 2 Configuration Sets Parameters of Serial Port 2(COMB). PCE-5133/5033 User Manual...
Page 49
3.2.2.10 HW Monitor Figure 3.20 HW Monitor Smart Fan Function SYSFAN1 Smart Fan setting Fan control mode setting. PCE-5133/5033 User Manual...
Page 50
Case Open Warning Enable or Disable Case Open Warning. CPU Warning Temperature Sets CPU Warning Temperature. ACPI Shutdown Temperature Sets ACPI Shutdown Temperature. 3.2.2.11 S5 RTC Wake Settings Figure 3.21 S5 RTC Wake Settings PCE-5133/5033 User Manual...
Page 51
Wake system from S5 Enable or disable System wake on alarm event. Select FixedTime System will wake on the hr::min::sec specified. PCE-5133/5033 User Manual...
Page 52
3.2.2.12 Serial Port Console Redirection Figure 3.22 Serial Port1 Console Redirection Figure 3.23 Serial Port1 Console Redirection COM1 Console Redirection Console Redirection Enable or Disable PCE-5133/5033 User Manual...
Page 53
Legacy Console Redirection Settings – Redirection COM Port – Resolution – 80x24 – 80x25 – Redirect After POST – Always Enable – BootLoader Console Redirection EMS Console Redirection Enable or Disable. 3.2.2.13 Intel_TXT_Information Figure 3.24 Intel TXT Information PCE-5133/5033 User Manual...
Page 54
Figure 3.25 Intel TXT Information Chipset, BiosAcm, Cpu Txt, and Error code information. 3.2.2.14 PCI Subsystem Setting Figure 3.26 PCI Subsystem Setting PCE-5133/5033 User Manual...
Page 55
Figure 3.27 PCI Subsystem Setting 3.2.2.15 USB Configuration Figure 3.28 USB Configuration PCE-5133/5033 User Manual...
Page 56
Figure 3.29 USB Configuration Figure 3.30 USB Configuration PCE-5133/5033 User Manual...
Page 57
Figure 3.31 USB Configuration Figure 3.32 USB Configuration PCE-5133/5033 User Manual...
Page 58
Hub descriptor. KingstonDataTraveler 3.0 Mass storage device emulation type. “AUTO” enumerates devices according to their media format. Optical drives are emulated as “CDROM”, drives with no media will be emulated according to a drive type. PCE-5133/5033 User Manual...
Page 60
3.2.3.2 CSM Configuration Figure 3.35 CSM Configuration CSM Support Enable/Disable CSM Support PCE-5133/5033 User Manual...
Page 61
3.2.3.3 NVME Configuration Figure 3.36 NVME Configuration 3.2.3.4 NVME Device Options Settings Driver Health Provides Health Status for the Drivers/Controllers PCE-5133/5033 User Manual...
Page 62
3.2.4 Chipset Figure 3.37 System Agent (SA) Configuration System Agent (SA) Parameters PCH-IO Configuration PCH Parameters. PCE-5133/5033 User Manual...
Page 63
3.2.4.1 System Agent (SA) Configuration Figure 3.38 System Agent (SA) Configuration Figure 3.39 System Agent (SA) Configuration PCE-5133/5033 User Manual...
Page 64
Figure 3.40 System Agent (SA) Configuration Figure 3.41 System Agent (SA) Configuration PCE-5133/5033 User Manual...
Page 65
Figure 3.42 System Agent (SA) Configuration Figure 3.43 System Agent (SA) Configuration Memory Configuration Memory Configuration Parameters. Graphics Configuration Graphics Configuration. PCE-5133/5033 User Manual...
Page 66
PCH-IO Configuration Figure 3.44 PCH-IO Configuration PCI Express Configuration PCI Express Configuration settings. SATA And RST Configuration SATA Device Options Settings. Security Configuration Security Configuration Settings. HD Audio Configuration HD Audio Configuration Settings. PCE-5133/5033 User Manual...
Page 67
3.2.4.3 Security Figure 3.45 Security Figure 3.46 Security Administrator Password Set Administrator Password. User Password Set User Password. PCE-5133/5033 User Manual...
Page 70
Bootup NumLock State Select the keyboard NumLock state. Quiet Boot Enables or disables Quiet Boot. Boot Option #1 Sets the system boot order. Boot Option #2 Sets the system boot order. PCE-5133/5033 User Manual...
Page 71
3.2.4.5 Save & Exit Figure 3.52 Save & Exit Figure 3.53 Save & Exit PCE-5133/5033 User Manual...
Page 72
Figure 3.54 Save & Exit Figure 3.55 Save & Exit PCE-5133/5033 User Manual...
Page 73
Figure 3.56 Save & Exit Figure 3.57 Save & Exit PCE-5133/5033 User Manual...
Page 74
Saves Changes done so far to any of the setup options. Restore Defaults Restore/Load Default values for all the setup options. Save as User Defaults Saves the changes done so far as User Defaults. PCE-5133/5033 User Manual...
Advantech embedded platforms easier and simpler to adopt and operate with customer applications. This API and utility is only for Microsoft Windows desktop OS, so if users need Linux version API and utility, contact an Advantech rep- resentative for support.
The drivers for the PCE-5133/5033 are located on the Advantech Website. The driver in the folder will guide and link you to the utilities and drivers for Windows. Updates are provided via Service Packs from Microsoft®.
Before installing this driver, make sure the INF driver has been installed in your system. See Chapter 5 for information on installing the INF driver. Enter the Advantech support website, then search product by PCE-5133/5033. If you cannot see the driver contact Advantech.. Note! Intel only support x86_64 graphics driver for Windows 10.
PCE-5133/5033 has dual/single Gigabit Ethernet LANs with dedicated PCI Express x1 lanes. Intel I226LM (LAN1 & 2 of PCE-5133) and I226V (LAN1 & 2 of PCE-5033) offer bandwidths of up to 500 MB/sec, eliminating network bottlenecks in data flow. It incorporates Gigabit Ethernet at 2500 Mbps.
MEISetup.exe to complete the installation of ME driver. Note! If the Intel® Management Engine (Intel® ME) driver has not been suc- cessfully installed, you may see an error on a “PCI Simple Communica- tions Controller” in Device Manager. PCE-5133/5033 User Manual...
Introduction PCE-5133/5033 provides Intel® USB 3.2 (Gen2) and the data transfer rates of USB 3.2 (Gen2) (10 Gbps) which is 2 times faster that USB 3.2 (Gen1) (5 Gbps). PCE-5133/5033 User Manual...
RAID 0 array is then mirrored by a RAID 1 component. 10.2 SATA RAID Driver and Utility Setup Enter the Advantech support website, then search product PCE-5133(PCE-5033 does not Support RAID). You can see driver inside. PCE-5133/5033 User Manual...
Page 89
Appendix Programming the Watchdog Timer...
Introduction The PCE-5133/5033’s watchdog timer can be used to monitor system software oper- ation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to pro- gram it.
2E (hex), then write/read data to/from the assigned register through data port 2F (hex). Unlock NCT6126D Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog timer Lock NCT6126D PCE-5133/5033 User Manual...
Page 92
Bit 5: Write 1 to generate a timeout signal immediately and auto- write matically return to 0. [default=0] Bit 4: Read status of watchdog timer, 1 means timer is “timeout”. AA (hex) Write this address to I/O port 2E (hex) to lock NCT6126D. PCE-5133/5033 User Manual...
VGA Connector (VGA1) Table B.1: VGA Connector (VGA1) Signal Signal Green Blue H-SYNC V-SYNC RS-232 Serial Port (COM12) Table B.2: RS-232 Serial Port (COM2) Signal SOUT PCE-5133/5033 User Manual...
Power LED and Keyboard Lock Connector (JFP3/PWR_LED and KEY LOCK) Table B.6: Power LED and Keyboard Lock Connector (JFP3/PWR_LED and KEY LOCK) Signal LED power (+3.3 V) External Speaker Connector (JFP2/SPEAKER) Table B.7: External Speaker Connector (JFP2/SPEAKER) Signal SPK_CN17P1 SPK_CN17P2 SPK_CN17P3 SPK_CN17P4 PCE-5133/5033 User Manual...
SM Bus Connector (JFP2/SNMP) Table B.12: SM Bus Connector (JFP2/SNMP) Signal SMB_DATA SMB_CLK B.13 LAN1 and LAN2 LED Connector (LANLED1) Table B.13: LAN1 and LAN2 LED Connector (LANLED1) Signal #LAN1_ACT #LAN2_ACT V33_AUX V33_AUX #LAN1_LINK1000 #LAN2_LINK1000 #LAN1_LINK100 #LAN2_LINK100 V33_AUX PCE-5133/5033 User Manual...
Timer/Counter Timer/Counter 8254 Timer LPC/eSPI LPC/eSPI Forwarded to LPC/eSPI NMI controller NMI controller Processor I/F Microcontroller Microcontroller Forwarded to LPC/eSPI NMI controller NMI controller Processor I/F Microcontroller Microcontroller Forwarded to LPC/eSPI NMI controller NMI controller Processor I/F PCE-5133/5033 User Manual...
Page 100
Gameport low Forwarded to LPC/eSPI 4D0h -4D1h Interrupt controller Interrupt controller Interrupt controller CF9h Reset generator Reset generator Interrupt controller Note! If the Port 61 alias enable bit (GCS.P61AE) bit is set. Otherwise, the tar- get is PCI. PCE-5133/5033 User Manual...
PCI slot 2 AD30 INT C, D, A, B GNT B REQ B PCI slot 3 AD29 INT D, A, B, C GNT C REQ C PCI slot 4 AD28 INT A, B, C, D GNT D REQ D PCE-5133/5033 User Manual...
OUT DX,AL OUT DX,AL --------------------------------------------------------------- Configure logical device, configuration register CRE0,CRE1,CRE2 --------------------------------------------------------------- MOV DX,2EH MOV AL,09H OUT DX,AL DEC DX MOV AL,30H OUT DX,AL INC DX IN AL,DX OR AL,10000000B; GPIO7 is active DEC DX MOV AL,07H PCE-5133/5033 User Manual...
Page 105
;Set GPIO is normal not inverter OUT DX,AL; DEC DX MOV AL,E1H OUT DX,AL INC DX MOV AL,??H ; Put the output value into AL OUT DX,AL ------------------------------------------ Exit extended function mode | ------------------------------------------ MOV DX,2EH MOV AL,AAH OUT DX,AL PCE-5133/5033 User Manual...
Need help?
Do you have a question about the PCE-5133 and is the answer not in the manual?
Questions and answers