Page 2
Thank you for choosing the Akuvox S562 series indoor monitor. This manual is intended for the administrators who need to properly configure the indoor monitor. This manual is written based on firmware 562.30.10.115, and it provides all the configurations for the functions and features of the S562 series indoor monitor.
Page 3
Residents can communicate with visitors via audio/video calls, and it supports unlocking the door remotely. It is more convenient and safer for residents to check the visitor's identity through its video preview function. S562 series are often applied to scenarios such as villas, apartments, and buildings.
Page 4
Model Specification Model Specification Model Model S562 S562 ✔ Touch Screen Resolution 1024x600 Wi-Fi IEEE 802.11 b/g/n Bluetooth × × RS485 Alarm In...
Page 5
Introduction to Configuration Menu Introduction to Configuration Menu Status: This section gives you basic information such as product information, Network Information, Status account information, etc. Account: This section concerns the SIP account, SIP server, proxy server, transport protocol type, Account audio &...
Page 7
Intercom Call Configuration Intercom Call Configuration IP Call & IP Call Configuration IP Call & IP Call Configuration An IP call is a direct call between two intercom devices using their IP addresses, without a server or a PBX. IP calls work when the devices are on the same network. Make IP Calls Make IP Calls To make a direct IP call on the device Call >...
Page 8
IP Call Configuration IP Call Configuration To configure the IP call feature and port on the device web Device > Call Feature > Others Device > Call Feature > Others interface. Parameter Set-up : Parameter Set-up Direct IP Call Direct IP Call: if you do not allow direct IP calls to be made on the device, you can untick the check box to terminate the function.
Page 9
SIP Account Registration Each device needs a SIP account to make and receive SIP calls. Akuvox intercom devices support the configuration of two SIP accounts, which can be registered under two independent servers. On the device screen, navigate to Settings > Advance Settings > Account Settings >...
Page 10
Password from third-party service provider. Password SIP Server Configuration SIP Server Configuration SIP servers enable devices to establish and manage call sessions with other intercom devices using the SIP protocol. They can be third-party servers or built-in PBX in Akuvox indoor monitor.
Page 11
The registration period ranges from 120-65535 120-65535 sec with 1800 1800 by default. a. To register SIP account for Akuvox indoor monitors, obtain Server Address Server Address and Port Port from Akuvox indoor monitor PBX screen.
Page 12
Parameter Set-up : Parameter Set-up Preferred Outbound Proxy Server Preferred Outbound Proxy Server: the IP address of the outbound proxy server. Preferred Outbound Proxy Server Port Preferred Outbound Proxy Server Port: the port number to establish call session via the outbound proxy server. Alternate Outbound Proxy Server Alternate Outbound Proxy Server: the IP address for the backup outbound proxy server.
Page 13
Return Code When DND Return Code When DND : select what code should be sent to the calling device via SIP server when you reject the incoming calls: 404 for Not Found; 480 for Temporary 404 for Not Found; 480 for Temporary Unavailable;...
Page 14
Max RTP port: the port value to establish the endpoint for the exclusive data transmission range. Data Transmission Type Configuration Data Transmission Type Configuration Akuvox intercom devices support four data transmission protocols: User Datagram User Datagram Protocol(UDP), Transmission Control Protocol(TCP Protocol(UDP)
Page 15
Security Security Monitor and Image Monitor and Image Monitor Setting Monitor Setting You can add up to four video streams using RTSP. If the Display in Call function is enabled, the video of the added monitor device will show up when it calls the indoor monitor. Navigate to Device >...
Page 16
Username Username : the username of the monitoring device for authentication. Password Password : the password of the monitoring device for authentication. Display In Call Display In Call: enable it to display the monitoring video during a call. Note Note You can import and export the monitoring device settings via a template in .xml format.
Page 17
Web Camera Setting Web Camera Setting You can configure the monitor feature for third-party cameras on the web Device > Monitor > Device > Monitor > Web Camera interface. Web Camera Parameter Set-up: Parameter Set-up: Device Name Device Name : the name of the third-party camera. RTSP Address RTSP Address : the RTSP URL for the third-party camera.
Page 18
RTSP Authentication RTSP Authentication With RTSP authentication, users can monitor the indoor monitor via RTSP audio stream. This feature can be applied to, for example, listen to the baby in the baby’s room for safety. To set it up, go to Settings > Basic Settings >...
Page 19
Alarm and Arming Configuration Alarm and Arming Configuration The Arming function is designed to enhance home security by offering three modes with custom zone settings for connected sensors. When armed, the device will sound a siren and notify specific people if a sensor detects something unusual. Configure Alarm and Arming on the Device Configure Alarm and Arming on the Device To configure the arming and disarm code on the device Arming >...
Page 20
Configure Location-based Alarm Configure Location-based Alarm Configure the alarm sensor on the device Arming > Arming Mode Arming > Arming Mode screen in the same way you do on the web interface. Parameter Set-up: Parameter Set-up: Location Location: displays which location the detection device is in, including Bedroom, Guest Bedroom, Guest room, Hall, Window, Balcony, Kitchen, Study room, Hall, Window, Balcony, Kitchen, Study, and Bathroom...
Page 21
Gas, and Urgency Urgency. Defence Delay Defence Delay: it means when users change the arming mode from other modes, there will be 90-second delay time to get activated. Alarm Delay Alarm Delay: it means when the sensor is triggered, there will be 90-second delay time to announce the notification.
Page 22
Configure Alarm Text Configure Alarm Text Once the alarm sensor is configured, you can access the device's web interface to personalize the alert content displayed on the screen when an alarm is triggered. Navigate to Arming > Zone Setting > Customized Alarm Arming >...
Page 23
Alarm Action Configuration Alarm Action Configuration When the alarm sensor is triggered, it can start different actions, such as HTTP commands, SIP messages, calls, and local relay activation, if they are set up. To select and set up actions on the web Arming > Alarm Action Arming >...
Page 24
The device can send messages to a designated device when the alarm is triggered. To set this up, enter a SIP number or IP address along with the message content. Parameter Set-up: Parameter Set-up: Receiver Receiver: the SIP number or IP number to receive the message. SIP Message SIP Message : the message sent to the designated SIP number or IP number when the alarm is triggered.
Page 25
Screen Unlock Setting Screen Unlock Setting To prevent unauthorized access to the device when it is not being used, enable the Screen Lock function. This feature automatically locks the device after a period of inactivity, requiring a password to unlock. You can enable the screen lock function directly on the device Settings >...
Page 26
Screen Unlock by PIN Code Screen Unlock by PIN Code To unlock the screen, users need to enter the preset PIN code. Navigate to the Settings > Advance Settings > Protected Code Settings > Advance Settings > Protected Code screen and select System System Code to change a new password.
Page 27
Power Output Setting The indoor monitor can serve as a power supply to the Akuvox door phone with 12V power supply for example E10. You can enable the power output, then connect the door phone to the RJ45 port on the indoor monitor.
Page 28
If the mode is off, the device can use both the new formats above and the old format below: l http://deviceIP/fcgi/do? action=OpenDoor&UserName=username&Password=password&DoorNum=1 4. It is not allowed to import/export configuration files in tgz. format between a device with the high security mode and another one without it. For assistance with file transfer, please contact Akuvox technical support.
Page 29
Lift Control Lift Control You can summon a lift via the lift control feature. Configure Lift Control Configure Lift Control To enable and set the display status Lift icon on the device web Device > Lift > Lift Control Device > Lift > Lift Control interface.
Page 30
If there are huge amounts of prompts that need to be added, you can click Export Export tab to export the template and import the file after editing.
Page 31
Call Logs Call Logs If you want to check on the calls inclusive of the dial-out calls, received calls, and missed calls in a certain period of time, you can check and search the call log on the device web interface and export the call log from the device if needed.
Page 33
Firmware Upgrade Firmware Upgrade Akuvox devices can be upgraded on the device web interface. Navigate to Upgrade > Basic Upgrade > Basic interface. Note Note Firmware files should be .rom format for an upgrade.
Page 34
Backup Backup You can import or export encrypted configuration files to your Local PC. Navigate to Upgrade > Advanced > Others Upgrade > Advanced > Others interface if needed.
Page 35
Password Modification Password Modification Modify Device Basic Setting Password Modify Device Basic Setting Password To do the configuration on device Settings > Advance Settings > Protected Code Settings > Advance Settings > Protected Code screen to choose System Code System Code to change a new password. The default password is 123456. Modify Device Advance Setting Password Modify Device Advance Setting Password This password is used to enter the advance settings of the device, including password settings,...
Page 36
Modify Device W eb Interface Password Modify Device W eb Interface Password To modify web interface password, you can do it on device web interface. Select Admin Admin for the administrator account and User User for the User Account. Click the Change Password Change Password tab to change the password.
Page 37
Note Note There are two accounts, one is admin, its password is admin, the other is user, and its password is user. Modify Screen Lock Password Modify Screen Lock Password Navigate to Settings > Advance Settings > Protected Code Settings > Advance Settings > Protected Code screen and choose Screen Screen Lock.
Need help?
Do you have a question about the S562 and is the answer not in the manual?
Questions and answers