Wilson Electronics weBoost Drive Sleek (U470035, 460035) Manual

Download the weBoost App

Use our app to guide you through setting up a weBoost cell phone signal booster in your home, business, or vehicle. Boost every network, including 5G, right away.

Package Contents

Mount Outside Magnetic Antenna

Identify a location on the top of your vehicle that is:

• Near the center of the roof
• At least 12 inches away from any other antennas
• At least 12 inches away from any windows (including sunroofs)

Clean the surface where you will place the outside antenna.

Mount the outside antenna by placing on top of vehicle.

NOTE: For aluminum roofs, an adhesive disk is included to mount the outside antenna (do not use if outside antenna will magnetize to the top of your vehicle).

Route Antenna Cable & Connect Booster

Route the cable into the vehicle. See examples below.
NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable.

Car/Sedan: Cable routed into rear side door.
NOTE: When going through a car wash, remember to remove your antenna.

SUV/Van/Hatchback: Cable routed into top of hatchback door.

Truck: Cable routed into side door.

Connect the cable from the outside antenna to the booster port labeled _ANTENNA by simply pressing the connector in until you hear a "click".
NOTE: Connecting cable from outside antenna to booster does not take much force.
The included Velcro® can be used to mount the booster out-of-the way on the floor under a seat or mounted to the side of the trunk. It is best to mount in a place where the cables cannot be tripped over or snagged (damaging the booster).
NOTE: The "hook" side of the Velcro® (already on the booster) can be used to attach to the carpet of many vehicles.

Route Cable To Front Of Vehicle & Connect To Cradle

We recommend routing the 15ft. fixed cable from the booster, under mats and between seats up to the front of the vehicle where the cradle will be located.

Connect booster cable to cradle cable.

Connect System To Power

Connect the power to the 12V* CLA port on your vehicle and route power cable back to the booster.
NOTE: We recommend routing with the same path as the cradle/booster cable (under mats and between seats). Cable clips are provided to help route & secure the cables.

Connect power cable to booster port labeled .
NOTE: The booster will be on whenever there is power from the 12V CLA port. If your vehicle always has power going to this port, you may want to unplug this when you're not driving so the booster does not drain your battery.
*Only 12V ports are supported.

Insert Your Phone Into Cradle

Make sure you have plenty of slack in the cable going up to the cradle (Velcro® straps included to manage excess cable). Insert your phone into cradle and watch your signal increase!

NOTE: A Magnetic Vent Mount & Adhesive Magnetic Dash Mount are provided which provides a versatile, safe and functional smartphone solution.

The FCC requires to never use the cell phone in the cradle next to your ear.

Troubleshooting

Solid White (LED on cradle)

This indicates that your booster is functioning properly and at maximum gain.

Light Off (LED on cradle)

Check/secure power connections to the CLA, booster, and cradle. If light shuts off, remove from vehicle port and plug back in to reset the system. For any questions or assistance contact our weBoost Customer Support Team (1-866-294-1660).

Dropped Calls

If you are regularly experiencing dropped calls in the same areas, turn off VoLTE/HD Voice in your phone's settings.

Safety Guidelines

Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment.
Any antenna used with this device must be located at least 8 inches from all persons.
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.
In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person.
You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless service provider.

E911 location information may not be provided or may be inaccurate for calls served by using this device.

FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05, SEE BELOW:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html

FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS PROVIDER, PLEASE SEE BELOW:
T-Mobile/Sprint/MetroPCS: https://www.t-mobile.com/support/coverage/register-a-signal-booster
Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp

Antenna Kit Options

The following accessories are certified by the FCC to be used with the Drive Sleek.
This radio transmitter 4726A-460035 has been approved by innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Specifications

Drive Sleek

Use our weBoost App to guide you through the installation. See inside page for more details.

NEED HELP?

www.weboost.com
support.weboost.com
1-866-294-1660