Korg Microkorg XL User Manual page 50

microKORG XL
DEST (Destination) ........................................................ [PITCH...P.INT6]
Selects the parameter (destination) that will be controlled by the modula-
tion. For example if you select Tune, modulation will be applied to the over-
all pitch of the timbre.
PITCH
OSC2.TUNE
OSC1 C1
OSC1 LVL
OSC2 LVL
NOISE.LVL
FILT1.BAL
CUTOFF1
RESO1
CUTOFF2
WS DEPTH
LEVEL
PANPOT
LFO1.FREQ
LFO2.FREQ
PORTMNTO
OSC1 C2
EG1 INT1
KEY TRK1
RESO2
EG1 INT2
KEY TRK2
ATTACK1
DECAY1
SUSTAIN1
RELEASE1
ATTACK2
DECAY2
SUSTAIN2
RELEASE2
ATTACK3
DECAY3
SUSTAIN3
RELEASE3
P.INT1
P.INT2
50
The pitch of the entire timbre.
The OSC2 page "TUNE".
The OSC1 page "C1". ( p. 36)
The MIXER page "OSC1 LVL".
The MIXER page "OSC2 LVL".
The MIXER page "NOISE.LVL".
The FILTER1 page "TYPE BAL".
The FILTER1 page "CUTOFF".
The FILTER1 page "RESO".
The FILTER2 page "CUTOFF".
The DRIVE/WS page "DEPTH".
The AMP page "LEVEL".
The AMP page "PANPOT".
The LFO1 page "FREQ".
The LFO2 page "FREQ".
The PITCH page "PORTMNTO".
The OSC1 page "C2". ( p. 36)
The FILTER1 page "EG1 INT".
The FILTER1 page "KEY TRK".
The FILTER2 page "RESO".
The FILTER2 page "EG1 INT".
The FILTER2 page "KEY TRK".
The EG1 page "ATTACK".
The EG1 page "DECAY".
The EG1 page "SUSTAIN".
The EG1 page "RELEASE".
The EG2 page "ATTACK".
The EG2 page "DECAY".
The EG2 page "SUSTAIN".
The EG2 page "RELEASE".
The EG3 page "ATTACK".
The EG3 page "DECAY".
The EG3 page "SUSTAIN".
The EG3 page "RELEASE".
The PATCH1 page "INTENSTY".
The PATCH2 page "INTENSTY".
P.INT3
P.INT4
P.INT5
P.INT6
INTENSTY (Patch Intensity)...................................................... [–63...63]
Specifies the depth of the effect produced by the modulation source.
With a setting of 0, there will be no modulation.
Setting example for "SOURCE" and "DEST"
SOURCE [1] DEST [2]
The EG1 or EG2 will vary the pitch of the entire timbre over
EG1/EG2 PITCH
time.
The EG1 or EG2 will vary the pan over time. By setting two
EG1/EG2 PANPOT patches to "MOD INT" settings with the opposite (+/–) value
you can create more complex panning.
LFO 1/LFO 2 PITCH Vibrato will be applied at the LFO1 or LFO2 frequency.
LFO 1/LFO 2 CUTOFF Wah will be applied at the LFO1 or LFO2 frequency.
LFO 1/LFO 2 LEVEL Tremolo will be applied at the LFO1 or LFO2 frequency.
LFO 1/LFO 2 PANPOT Auto pan will be applied at the LFO1 or LFO2 frequency.
VELOCITY LEVEL Velocity (keyboard playing strength) will affect the volume.
Keyboard position will gradually change the pan; lower
KEY TRK PANPOT
notes at the left, and higher notes at the right.
PITCH wheel operations or pitch bend change will move
P.BEND PANPOT
the sound between left and right.
The PATCH3 page "INTENSTY".
The PATCH4 page "INTENSTY".
The PATCH5 page "INTENSTY".
The PATCH6 page "INTENSTY".