Table of Contents
Advertisement
Quick Links
Tubular motor:
GEIGER XS56
Motor control:
XS56 SoftPerfection-X01
for rolling shutters with stoppers and anti-lift device
Type designation
GJ56..-E16
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
EN
1
EN
Advertisement
Table of Contents
Related Manuals for GEIGER XS56
Summary of Contents for GEIGER XS56
- Page 1 Tubular motor: GEIGER XS56 Motor control: XS56 SoftPerfection-X01 for rolling shutters with stoppers and anti-lift device Type designation GJ56..-E16 Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento www.geiger.de...
-
Page 2: Table Of Contents
1. General information Dear customer, By purchasing a GEIGER motor you have decided on a quality product from GEIGER. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property. -
Page 3: Intended Use
3. Intended use The tubular motors of the model range XS56 (GJ56..-E16) are designed for the operation of rolling shutters with anti-lift device and stoppers The motors may not be used for the operation of roller grilles, garage doors, furniture and lifting tools. -
Page 4: Safety Instructions For Assembly
A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by GEIGER connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable. -
Page 5: Installation Instructions
In order to adjust the end positions, a rolling shutter system with upper end stop and anti-lift device is required. The GEIGER XS56 is suitable for roller shutters with a 60 mm 8-sided shaft (length > 370mm), shaft material < 0.60 mm. -
Page 6: Information For The Specialist Electrician
1 sec 5 sec 1 sec 5 sec 1 sec 5 sec Please note: a break of at least 5 seconds must be respected between the different runs. 3. DONE! Gerhard Geiger GmbH & Co. KG | 100W2582 V000 0223... -
Page 7: Obstacle Recognition
After running several times, • The motor became too hot and has the motor breaks down and switched off. no longer responds. Try it again after a cooling time of about 15 min. 13. Maintenance The drive is maintenance-free. www.geiger.de... -
Page 8: Declaration Of Conformity
Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Roland Kraus | WEEE-Reg.-Nr. -
Page 9: Technical Data
The average sound pressure level data are intended for guidance only. The values were determined by GEIGER at a distance of 1 m, with a hanging motor at idle speed and averaged over 10 seconds. There is no reference to any specific test standard. - Page 10 Gerhard Geiger GmbH & Co. KG | 100W2582 V000 0223...
- Page 11 www.geiger.de...
- Page 12 They will be happy to assist you. Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen T +49 (0) 7142 9380 | F +49 (0) 7142 938 230 info@geiger.de | www.geiger.de Gerhard Geiger GmbH & Co. KG | 100W2582 V000 0223...
Need help?
Do you have a question about the XS56 and is the answer not in the manual?
Questions and answers