GEIGER SOLIDline GU4510 Original Assembly And Operating Instructions
With geiger-variouswireless control, for rolling shutters, screens and open style folding arm awnings
Hide thumbs
Also See for SOLIDline GU4510:
- Original assembly and operating instructions (16 pages) ,
- Original assembly and operating instructions (16 pages)
Table of Contents
Advertisement
Quick Links
Tubular motor:
GEIGER-SOLIDline
Motor control:
GEIGER-VariousWireless (GU45..F01)
for rolling shutters, screens and open style
folding arm awnings
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
EN
1
EN
Advertisement
Table of Contents
Related Manuals for GEIGER SOLIDline GU4510
Summary of Contents for GEIGER SOLIDline GU4510
- Page 1 Tubular motor: GEIGER-SOLIDline Motor control: GEIGER-VariousWireless (GU45..F01) for rolling shutters, screens and open style folding arm awnings Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento www.geiger.de...
-
Page 2: Table Of Contents
1. General information Dear customer, By purchasing a GEIGER motor you have decided on a quality product from GEIGER. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property. -
Page 3: Intended Use
GU 45 Motor control Torque in Nm Motor diameter GEIGER universal drive 4. Safety instructions ATTENTION: Important safety instructions. For personal safety, it is important to follow these instructions. Please keep these instructions for future reference. f Do not allow children to play with stationary controls. Keep remote controls away from children. -
Page 4: Safety Instructions For Assembly
A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by GEIGER connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable. -
Page 5: Installation Instructions
– Place the motor into the existing engine bearer and lock – Place the motor in a compatible engine bearer with clip system and lock with spring or rotating lever The GEIGER-SOLIDline motor is suitable for shaft diameters from 50 mm. www.geiger.de... -
Page 6: Information For The Specialist Electrician
3 metres as an “antenna“. Definition of „far range“: Distance of the hand-held transmitter to the motor control: min.1.5 metres, min. 1,5 m distance of the hand held transmitter to the motor connec- ting cable min.0.5 metres Gerhard Geiger GmbH & Co. KG | 100W0519 V001 0818... -
Page 7: Learning/Deleting The Transmitter
(1 x “click-click“). Keep the key pressed about 5 sec. max. 15 cm until the motor confirms the deleting of the transmitters with 1 x “click-click“. about. 5 sec. Please note: You can only delete all transmitters/sensors. It is not possible to delete an individual transmitter/sensor. www.geiger.de... -
Page 8: Adjustment Of The End Positions / Intermediate Position
Change/delete the end positions In order to change or delete the end positions, a new programming must be started (see «learning the end positions»). The learning mode must be activated first in order to adjust/delete the end positions (see page 7). Gerhard Geiger GmbH & Co. KG | 100W0519 V001 0818... -
Page 9: Learning The End Positions
In the far range pressed the DOWN key and keep it pressed until the hangings have reached the lower stop and the motor switches off automatically. The motor confirms with 1 x “click-click“. The lower end position is now stored. Programming is finished and the motor has changed to normal operation. min. 1,5 m www.geiger.de... - Page 10 The lower end position is now stored. The UP and DOWN keys are now assigned to the corresponding turning direction of the motor. min. Programming is finished and the motor 1,5 m has changed to normal operation. Gerhard Geiger GmbH & Co. KG | 100W0519 V001 0818...
- Page 11 Corrections with UP or DOWN key are possible. min. 1,5 m click- click Store lower end position: In the near range press UP or DOWN key for about 1 second. The motor actuates (1 x “click-click“). Programming is finished and the motor has changed to normal operation. max. 15 cm www.geiger.de...
- Page 12 In the near range press UP or DOWN key for about 1 second. The motor actuates (1 x “click-click“). The UP and DOWN keys are now assigned to the corresponding turning direction of the motor. max. 15 cm Gerhard Geiger GmbH & Co. KG | 100W0519 V001 0818...
-
Page 13: Teach Intermediate Position
3. Actuate key 3 sec. at close range to activate the learning mode of the sun protection B. 4. Actuate key 1 sec. at close range to program the transmitter of the sun protection B. 2 3 4 5 6 Same operation for three or more sun protections. www.geiger.de... -
Page 14: Deactivation Of The Close-Range Function
„UP“ button and keep it pushed for about 5 seconds until the motor confirms (2 x “click-click“). The motor must be disconnected from the mains briefly to active the close-range function. Gerhard Geiger GmbH & Co. KG | 100W0519 V001 0818... -
Page 15: Setting Of End Stops With Open Style Folding Arm Awnings
Corrections with UP or DOWN key are possible. min. 1,5 m Store lower end position: click- In the near range press UP or DOWN key for about click 1 second. The motor actuates (1 x “click-click“). Programming is finished and the motor has changed to normal operation. max. 15 cm www.geiger.de... - Page 16 Store lower end position: click In the near range press UP or DOWN key for about 1 second. The motor actuates (1 x “click-click“). Programming is finished and the motor has changed to normal operation max. 15 cm Gerhard Geiger GmbH & Co. KG | 100W0519 V001 0818...
-
Page 17: Transmitters
With a short key press of under 1.5 seconds, the intermediate position is travelled to. For stopping the travel movement a short key press in the opposite direction is sufficient. Should a sun-wind sensor be integrated into the system, the end positions are started in automatic mode (sun-on). www.geiger.de... -
Page 18: Obstacle Recognition
The average sound pressure level data are intended for guidance only. The values were determined by GEIGER at a distance of 1 m, with a hanging motor at idle speed and averaged over 10 seconds. There is no reference to any specific test standard. -
Page 19: What To Do If
In the interest of environmental protection, please contact your local government’s recycling or solid waste management department to learn more about the services it provides. Waste disposal of electric and electronic equipment Electrical and electronic equipment must be collected and disposed of separately in accordance with EU regulations. www.geiger.de... -
Page 20: Declaration Of Conformity
Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Dr.