GEIGER GJ5606-DuoDrive Original Assembly And Operating Instructions

GEIGER GJ5606-DuoDrive Original Assembly And Operating Instructions

With mechanical end stop for venetian blinds and exterior blinds

Advertisement

Venetian blind motor:
GEIGER-GJ5606-DuoDrive with mechanical end stop
For Venetian blinds and exterior blinds
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
09
39
1/min
1/min
EN
EN
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GJ5606-DuoDrive and is the answer not in the manual?

Questions and answers

Arone Thompson
March 20, 2025

WHats the average life expectancy of the motors

Subscribe to Our Youtube Channel

Summary of Contents for GEIGER GJ5606-DuoDrive

  • Page 1 Venetian blind motor: GEIGER-GJ5606-DuoDrive with mechanical end stop For Venetian blinds and exterior blinds Original-Montage- und Betriebsanleitung 1/min 1/min Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento www.geiger.de...
  • Page 2: Table Of Contents

    1. General information Dear customer, By purchasing a Geiger motor you have decided on a quality product from Geiger. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property.
  • Page 3: Safety Instructions

    The height of installation must be at least 1.5 m above the floor. f Permanently installed control devices must be attached visibly. f In case of devices extending horizontally, a horizontal distance of at least 0.4 m must be respected between the fully extended part and any other fixed element. www.geiger.de...
  • Page 4: Assembly Note

    A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by Geiger connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable.
  • Page 5: Installation Instructions

    7. Installation instructions Prior to installation please check to ensure there is no visible damage to the motor like cracks or open cables. Before fixing please check the strength of the masonry and of the  surface. Head rail opening at top: www.geiger.de...
  • Page 6 Head rail opening at bottom: Gerhard Geiger GmbH & Co. KG | 100W1591 V000 1118...
  • Page 7: Information For The Specialist Electrician

    If you press the DOWN adjustment button for the lower end position and DOWN direction, the Venetian blind can move over the lower turning position and move up again. If the Venetian blind hits the limit stop switch now, the GJ56 is not switched off and the Venetian blind could be damaged. www.geiger.de...
  • Page 8: What To Do If

    Restore free motion of the limit stop switch. Re-adjust the end positions 10. Maintenance The drive is maintenance-free. Gerhard Geiger GmbH & Co. KG | 100W1591 V000 1118...
  • Page 9: Technical Data

    11. Technical data Technical data GJ5606-DuoDrive with mechanical end stop GJ5606-DuoDrive Voltage 230 V~/50 Hz Current 0,60 A Cos Phi (cosj) > 0,95 Inrush current (factor) x 1,2 Power 145 W Torque 6 Nm Speed 9/39 rpm Protection class IP 54...
  • Page 10: Declaration Of Conformity

    Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Roland Kraus | WEEE-Reg.-Nr.
  • Page 11: Notes On Waste Disposal

    In the interest of environmental protection, please contact your local government’s recycling or solid waste management department to learn more about the services it provides. Waste disposal of electric and electronic equipment Electrical and electronic equipment must be collected and disposed of separately in accordance with EU regulations. www.geiger.de...
  • Page 12: En Gerhard Geiger Gmbh & Co. Kg | 100W1591 En V000

    They will be happy to assist you. Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen T +49 (0) 7142 9380 | F +49 (0) 7142 938 230 info@geiger.de | www.geiger.de Gerhard Geiger GmbH & Co. KG | 100W1591 V000 1118...

Table of Contents