Page of 80
Download Table of ContentsContents Print This PagePrint Bookmark

HP J4093A Installation Manual

Installation guide.
Hide thumbs

Advertisement

H P
ProCurve
Switches and Hubs
HP ProCurve Switch 1600M and 2424M
L e s s Wo r k , M o r e N e t w o r k
h t t p : / / w w w . h p . c o m / g o / p r o c u r v e

Advertisement

   Summary of Contents for HP J4093A

  • Page 1: Installation Guide

    ProCurve Switches and Hubs HP ProCurve Switch 1600M and 2424M Installation Guide L e s s Wo r k , M o r e N e t w o r k h t t p : / / w w w . h p . c o m / g o / p r o c u r v e...

  • Page 3

    HP ProCurve Switch 1600M and 2424M Installation Guide...

  • Page 4

    5967-9953 performance, or use of this material. December 1998 Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished Applicable Products by Hewlett-Packard. HP ProCurve Switch 1600M (HP J4120A)

  • Page 5: Table Of Contents

    Contents 1 Introducing the HP ProCurve Switch 1600M and 2424M Front of the Switches ......... . 1-2 Network Ports .

  • Page 6: Table Of Contents

    5. Connect the Switch to a Power Source ..... . 2-13 6. Connect the Network Cables ....... 2-14 Using the RJ-45 Connectors (10/100Base-TX ports) .

  • Page 7: Table Of Contents

    A Specifications Physical ..........A-1 Electrical .

  • Page 9

    HP ProCurve Switch 1600M (HP J4120A) HP ProCurve Switch 2424M (HP J4093A) Throughout this manual, these switches will be abbreviated as the Switch 1600M and Switch 2424M, or when common features are being described, as the Switch 1600M and 2424M.

  • Page 10: Front Of The Switches, Network Ports

    Introducing the HP ProCurve Switch 1600M and 2424M Front of the Switches Front of the Switches Slot for Self Test Switch Module Reset and Clear (Switch 1600M) buttons HP ProCurve Switch 1600M Console Mode Select button Status LEDs for 10/100Base-TX RJ-45 ports port and indicator LEDs switch module,...

  • Page 11: Leds

    Introducing the HP ProCurve Switch 1600M and 2424M Front of the Switches LEDs Table 1-1. Switch LEDs Switch LEDs State Meaning Power The switch is receiving power. (green) The switch is NOT receiving power. Fault The normal state; indicates that there are no fault conditions on the switch. (orange) †...

  • Page 12: Mode Select Button And Indicator Leds

    Introducing the HP ProCurve Switch 1600M and 2424M Front of the Switches Table 1-2. Switch Module LEDs Port LEDs State Meaning Link Indicates the port is enabled and receiving a link beat signal (for the twisted-pair ports), or a strong enough light level (for the fiber-optic ports on the switch modules) from the connected device.

  • Page 13: Console Port, Reset Button, Clear Button

    Introducing the HP ProCurve Switch 1600M and 2424M Front of the Switches Console Port This port is used to connect a console to the switch by using the serial cable supplied with the switch. This connection is described under “Connect a Console to the Switch”...

  • Page 14: Back Of The Switches, Power Connector, Slot For Switch Module (switch 2424m)

    Introducing the HP ProCurve Switch 1600M and 2424M Back of the Switches Back of the Switches cooling vent - make sure this is not obstructed for proper switch operation HP ProCurve Switch 1600M AC power connector HP ProCurve Switch 2424M Slot for Switch Module (Switch 2424M)

  • Page 15: Switch Features

    Introducing the HP ProCurve Switch 1600M and 2424M Switch Features Switch Features The features of the Switch 1600M and 2424M include: 16 or 24 autosensing 10/100Base-TX RJ-45 ports a slot for installing any of the available switch modules—as of this printing, these include: •...

  • Page 16: Switch Operation Overview, Address Table Operation

    Introducing the HP ProCurve Switch 1600M and 2424M Switch Operation Overview Switch Operation Overview Address Table Operation Address Learning. As devices are connected to the switch ports, either directly or through hubs or other switches, the MAC addresses of those devices are learned automatically and stored in the 8000-entry address table featured by the Switch 1600M and 2424M.

  • Page 17: Simultaneous Network Communications, Effect Of Vlans

    Introducing the HP ProCurve Switch 1600M and 2424M Switch Operation Overview Simultaneous Network Communications As part of the traffic isolation benefits provided by the Switch 1600M and 2424M address table operation, the switches enhance network performance because they can conduct multiple, simultaneous network connections. Instead of sharing the network bandwidth, as in connections to a hub, each connection has its own 10 Mbps, 100 Mbps, or 1000 Mbps bandwidth to use.

  • Page 19: Included Parts

    Installing the Switch 1600M and 2424M The HP Switch 1600M and 2424M are easy to install units. They each come with an accessory kit that includes the brackets for mounting the switch in a standard 19-inch telco rack or an equipment cabinet, or on a wall, and with rubber feet that can be attached so the switch can be securely located on a horizontal surface.

  • Page 20: Physical, Installation Procedures, Summary

    Installing the Switch 1600M and 2424M Installation Procedures Installation Procedures Summary Follow these easy steps to install your switch. The rest of this chapter provides details on these steps. Prepare the installation site (page 2-4). Make sure that the physical environment into which you will be installing the switch is properly prepared including having the correct network cabling ready to connect to the switch, and having a good location for the switch.

  • Page 21: Connectors, Safety, Installation Precautions:

    Installing the Switch 1600M and 2424M Installation Procedures Installation Precautions: Follow these precautions when installing your HP Switch 1600M and 2424M. W a r n i n g The rack or cabinet should be adequately secured to prevent it from becoming unstable and/or falling over.

  • Page 22: Prepare The Installation Site

    Installing the Switch 1600M and 2424M Installation Procedures 1. Prepare the Installation Site Cabling Infrastructure - Ensure that the cabling infrastructure meets the necessary network specifications. See the following table for cable types and lengths, and see appendix B, “Cables and Connectors” for more information: Table 2-1.

  • Page 23

    Installing the Switch 1600M and 2424M Installation Procedures Installation Location - Before installing the switch, plan its location and orientation relative to other devices and equipment: • In the front of the switch, leave at least 7.6 cm (3 inches) of space for the twisted-pair and fiber-optic cabling.

  • Page 24

    Installing the Switch 1600M and 2424M Installation Procedures 2. Install Switch Module (optional) Install a switch module into the slot as shown in the illustration on the next page. For installation details, see the instructions in the Installation Guide that comes with the module. The slot cover can be removed with either a flat-bladed or Torx T-10 screw- driver.

  • Page 25

    Installing the Switch 1600M and 2424M Installation Procedures Installing a Switch Module in the Switch 1600M Insert module into the guides and slide it in until it stops. Then press in firmly until the module “snaps” into place and is flush with the face of the switch.

  • Page 26: Electrical, Verify The Switch Passes Self Test

    Installing the Switch 1600M and 2424M Installation Procedures 3. Verify the Switch Passes Self Test Before mounting the switch in its network location, you should first verify that it is working properly by plugging it into a power source and verifying that it passes its self test.

  • Page 27: Led Behavior:

    Installing the Switch 1600M and 2424M Installation Procedures switch port LEDs Self Test LED Power and Fault LEDs When the switch is powered on, it performs its diagnostic self test. The self test takes approximately 45 seconds to complete. LED Behavior: During the self test: •...

  • Page 28: Mount The Switch, Rack Or Cabinet Mounting

    Installing the Switch 1600M and 2424M Installation Procedures 4. Mount the Switch After you have verified that the switch passes self test, you are ready to mount the switch in a stable location. The Switch 1600M and 2424M can be mounted in these ways: in a rack or cabinet on a horizontal surface...

  • Page 29

    Installing the Switch 1600M and 2424M Installation Procedures Partially install a screw (5/8-inch number 12-24) into the top hole of a pair of holes that are 0.5 inches apart in each rack/cabinet upright as shown in the illustration below. Ensure that the screws are at the same level in each upright.

  • Page 30: Horizontal Surface Mounting

    Installing the Switch 1600M and 2424M Installation Procedures Install the other number 12-24 screw into the upper hole in each bracket. Tighten these screws. install additional screw Horizontal Surface Mounting Attach the bumper feet included in the accessory kit to the bottom of the switch, and place the switch on a table or other horizontal surface.

  • Page 31: Wall Mounting, Connect The Switch To A Power Source

    Installing the Switch 1600M and 2424M Installation Procedures Wall Mounting You can mount the switch on a wall as shown in the illustration below. C a u t i o n The switch should be mounted only to a wall or wood surface that is at least 1/2-inch plywood or its equivalent.

  • Page 32: Connect The Network Cables, Using The Rj-45 Connectors (10/100base-tx Ports)

    Installing the Switch 1600M and 2424M Installation Procedures 6. Connect the Network Cables Connect the network cables, described under “Cabling Infrastructure” (page 2-4), from the network devices or your patch panels to the fixed RJ-45 ports on the switch or the ports on any module you have installed in the switch. Using the RJ-45 Connectors (10/100Base-TX ports) To connect: Push the RJ-45 plug into the RJ-45...

  • Page 33: Optional) Connect A Console To The Switch, Terminal Configuration

    Installing the Switch 1600M and 2424M Installation Procedures 7. (Optional) Connect a Console to the Switch The Switch 1600M and 2424M have a full-featured, easy to use console interface for performing the following tasks: Monitor switch and port status and observe network activity counters Modify the switch’s configuration Read the event log and access diagnostic tools to help in troubleshooting Download new software to the switch...

  • Page 34: Direct Console Access, Telnet Console Access

    Installing the Switch 1600M and 2424M Installation Procedures Direct Console Access To connect a console to the switch, follow these steps: Switch 1600 HP J4120A Power console port Connect the PC or Fault Console terminal to the switch’s Reset Console Port using the console cable included with the switch.

  • Page 35: Sample Network Topologies, As A Desktop Switch

    Installing the Switch 1600M and 2424M Sample Network Topologies Sample Network Topologies This section shows you a few sample network topologies in which the Switch 1600M and 2424M are implemented. For more topology information, see the document Designing HP AdvanceStack Workgroup Networks, which can be found on the HP network products World Wide Web site, http://www.hp.com/ go/procurve.

  • Page 36: As A Segment Switch

    Installing the Switch 1600M and 2424M Sample Network Topologies As a Segment Switch Server with category 5 twisted-pair “straight-through” “Fast” Ethernet cable for 100 Mbps connection to server twisted-pair “cross-over” Switch 1600M 100 Base-FX cables to hubs fiber-optic cable to backbone “Fast”...

  • Page 37: Connecting To A Backbone Switch

    Installing the Switch 1600M and 2424M Sample Network Topologies Connecting to a Backbone Switch Switch 2424M to Gigabit-Ethernet backbone Switch 8000M Switch 1600M The simpler desktop and segment networks shown in the previous two examples can easily be combined and expanded. For example, you could use an HP ProCurve Switch 8000M to interconnect each of your smaller switched workgroups to form a larger switched network.

  • Page 38: Hot Swapping The Switch Module, Adding Or Replacing The Module, Changing The Module Type

    Installing the Switch 1600M and 2424M Hot Swapping the Switch Module Hot Swapping the Switch Module Any of the HP ProCurve Switch Modules can be “hot swapped”, that is installed or replaced while the switch is powered on. The procedures differ slightly, though, between adding a new module to the empty slot or replacing the module with the same type, and exchanging the module with a different type.

  • Page 39: Where To Go From Here

    Installing the Switch 1600M and 2424M Where to Go From Here Where to Go From Here Your switch is now correctly installed and is able to send and receive data between end nodes, servers, and printers. The Switch 1600M and 2424M are plug-and-communicate network devices requiring no configuration.

  • Page 41: Troubleshooting

    Troubleshooting This chapter describes how to troubleshoot your Switch 1600M and 2424M. Note that this document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting using the soft- ware tools available with the switch, including the full-featured console interface, the built-in web browser interface, and HP TopTools for Hubs &...

  • Page 42: Basic Troubleshooting Tips

    Troubleshooting Basic Troubleshooting Tips Basic Troubleshooting Tips Most problems are caused by the following situations. Check for these items first when starting your troubleshooting: Incorrect switch-to-switch or switch-to-hub connections. If you have connected your switch to another switch or a hub by using twisted- pair cable from an RJ-45 MDI-X connector on your switch to an MDI-X connector on the other switch or hub, you must use a crossover cable.

  • Page 43

    Troubleshooting Basic Troubleshooting Tips In addition, you should make sure that your network topology contains no data path loops. Between any two end nodes, there should be only one active cabling path at any time. Data path loops will cause broadcast storms that will severely impact your network performance.

  • Page 44: Diagnosing With The Leds

    Troubleshooting Diagnosing with the LEDs Diagnosing with the LEDs Tables 3-1 shows LED patterns on the switch and the switch modules that indicate problem conditions. Check in the table for the LED pattern that you see on your switch. Refer to the corresponding diagnostic tip on the next few pages. Table 3-1.

  • Page 45

    Troubleshooting Diagnosing with the LEDs Diagnostic Tips: Problem Solution The switch is not 1. Verify that the power cord is plugged into an active power source and to the switch. Make sure these connections are snug. plugged into an active AC power 2.

  • Page 46

    Troubleshooting Diagnosing with the LEDs Problem Solution A module was When you “hot swap” modules in the module slot, if you install a different module type installed in the than the one that was previously installed in the slot, you must reset the switch. This slot that is a allows the switch processor to properly initialize and configure the new module type.

  • Page 47: Proactive Networking

    Troubleshooting Proactive Networking Proactive Networking The Switch 1600M and 2424M have built-in management capabilities that proactively help you manage your network including: finding and helping you fix the most common network error conditions (for example, faulty network cabling, and non-standard network topolo- gies) informing you of the problem with clear, easy-to-understand messages recommending network configuration changes to enhance the perfor-...

  • Page 48: Hardware Diagnostic Tests, Testing The Switch By Resetting It, Checking The Switch Leds

    Troubleshooting Hardware Diagnostic Tests Hardware Diagnostic Tests Testing the Switch by Resetting It If you believe that the switch is not operating correctly, you can reset the switch to test its circuitry and operating code. To reset a switch, either: Unplug and plug in the power cord (power cycling) Press the reset button on the front of the switch Power cycling the switch and pressing the Reset button both cause the switch...

  • Page 49: Testing Twisted-pair Cabling, Testing Switch-to-device Network Communications

    Troubleshooting Hardware Diagnostic Tests Testing Twisted-Pair Cabling If you think the cable should work but still isn’t working, it may not be compatible with the IEEE 802.3 Type 10Base-T or 100Base-TX standards. The twisted-pair cables attached to the Switch 1600M and 2424M must be compat- ible with these standards.

  • Page 50: Testing End-to-end Network Communications, Restoring The Factory Default Configuration

    Troubleshooting Restoring the Factory Default Configuration Testing End-to-End Network Communications Both the switch and the cabling can be tested by running an end-to-end communications test -- a test that sends known data from one network device to another through the switch. For example, if you have two PCs on the network that have LAN adapters between which you can run a link-level test or Ping test through the switch, you can use this test to verify that the entire communication path between the two PCs is functioning correctly.

  • Page 51: Hp Customer Support Services, Before Calling Support

    HP Customer Support Services HP Customer Support Services If you are still having trouble with your switch, Hewlett-Packard offers support 24 hours a day, seven days a week through the use of a number of automated electronic services. See the Customer Support/Warranty booklet that came with your switch for information on how to use these services to get technical support.

  • Page 53: Environmental

    Specifications Except where otherwise noted, the following specifications apply to both the Switch 1600M and the Switch 2424M. Physical Width: 44.2 cm (17.4 in) Depth: 33.5 cm (13.2 in) Height: 6.6 cm (2.6 in) Weight: • Switch 1600M 4.5 kg (9.9 lbs) •...

  • Page 54: Acoustic, Connectors, Twisted Pair, Fiber-optic

    Specifications Acoustic • Switch 1600M: Geraeuschemission LwA=54 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 • Switch 2424M: Geraeuschemission LwA=55 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 Connectors The 10/100 Mbps RJ-45 twisted-pair ports are compatible with the IEEE 802.3u 100Base-TX and IEEE 802.3 Type 10Base-T standards. The 100 Mbps SC fiber-optic ports on the 100Base-FX Switch Module are compatible with the IEEE 802.3u 100Base-FX standard.

  • Page 55: Cables

    Connectors and Cables This appendix includes switch connector information and network cable information for cables that should be used with the Switch 1600M and 2424M, including minimum pin-out information and specifications for twisted-pair cables. N o t e Incorrectly wired cabling is the most common cause of problems for LAN communications.

  • Page 56

    Connectors and Cables Cables Twisted-Pair Category 3, 4, or 5 100-ohm unshielded twisted-pair (UTP) 10 Mbps Operation or shielded twisted-pair (STP) cable, complying with IEEE 802.3 Type 10Base-T specifications, fitted with RJ-45 connectors 100 Mbps Operation Category 5 100-ohm UTP or STP cable, complying with IEEE 802.3u 100Base-TX specifications, fitted with RJ-45 connectors Fiber-Optic...

  • Page 57: Twisted-pair Cable/connector Pin-outs

    Connectors and Cables Twisted-Pair Cable/Connector Pin-Outs Twisted-Pair Cable/Connector Pin-Outs The RJ-45 connectors on the 10/100Base-TX ports on the Switch 1600M and 2424M are all wired as MDI-X ports. The type of twisted-pair cable you connect to these ports (either “straight through” or “crossover”) depends on the type of device at the other end of the cable.

  • Page 58: Mbps Or 100 Mbps Network Connection

    Connectors and Cables Twisted-Pair Cable/Connector Pin-Outs Twisted-Pair Cable for Switch (MDI-X) to Computer (MDI) 10 Mbps or 100 Mbps Network Connection To connect PCs or other MDI network devices to the switch 10 Mbps or 100 Mbps MDI-X ports, use a “straight-through” cable. Connector “A”...

  • Page 59

    Connectors and Cables Twisted-Pair Cable/Connector Pin-Outs Twisted-Pair Cable for Switch (MDI-X) to Hub or Switch (MDI-X) 10 Mbps or 100 Mbps Network Connection To connect hubs or switches or other MDI-X network devices to the switch 10 Mbps or 100 Mbps MDI-X ports, use a “crossover” cable. Connector “A”...

  • Page 60: For 10 Mbps Or 100 Mbps Operation, Twisted-pair Straight-through Cable, Twisted-pair Cross-over Cable

    Connectors and Cables Twisted-Pair Cable/Connector Pin-Outs Twisted-Pair Cable Pin Assignments for 10 Mbps or 100 Mbps Operation Twisted-Pair Straight-Through Cable Switch End (MDI-X) Computer, Transceiver, or Other MDI Port End Signal Pins Pins Signal receive + transmit + receive - transmit - transmit + receive +...

  • Page 61: Safety Information

    Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death.

  • Page 62

    Safety and EMC Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort.

  • Page 63: Hinweise Zur Sicherheit

    Safety and EMC Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die Verletzungen oder sogar Todesfälle verursachen kann.

  • Page 64: Considerazioni Sulla Sicurezza

    Safety and EMC Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza Simbolo di riferimento alla documentazione. Se il prodotto è contras- segnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNINGdenota un pericolo che può causare lesioni o morte.

  • Page 65: Consideraciones Sobre Seguridad

    Safety and EMC Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte.

  • Page 66

    Safety and EMC Regulatory Statements Safety Information (Japan) Safety Information (Japan)

  • Page 67

    Safety and EMC Regulatory Statements Safety Information (China) Safety Information (China)

  • Page 68: Emc Regulatory Statements

    Safety and EMC Regulatory Statements EMC Regulatory Statements EMC Regulatory Statements U.S.A. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.

  • Page 69

    Safety and EMC Regulatory Statements EMC Regulatory Statements Korea Taiwan...

  • Page 70: European Community

    Safety and EMC Regulatory Statements EMC Regulatory Statements European Community C-10...

  • Page 71

    Index Numerics 10/100Base-TX ports cabinet location on switch … 1-2 mounting the switch in … 2-10 100 LED … 1-3 cables 100Base-FX 100Base-FX connections, length limitations … 2-4 connections … 2-4 ports, cables used with … 2-4, B-2 fiber-optic cable specifications … B-2 100Base-TX 100Base-TX connections …...

  • Page 72

    Clear button deleting passwords … 1-5 electrical specifications, switch … A-1 description … 1-5 EMC regulatory statements … C-8 location on switch … 1-2, 1-5 environmental specifications, switch … A-1 restoring factory default configuration … 1-5, 3-10 configuration restoring factory defaults … 1-5, 3-10 factory default configuration, restoring …...

  • Page 73

    selecting the display … 1-4 mode select indicators … 1-3 horizontal surface, mounting switch on … 2-12 Module Status … 1-3 hot swapping on switch … 1-3 resetting the switch for new module type … 2-20 on switch modules … 1-4 switch modules …...

  • Page 74

    power source connecting the switch to … 2-13 network cables precautions 100Base-FX connections … 2-4 mounting the switch … 2-3 100Base-TX connections … 2-4 power requirements … 2-3 10Base-FL connections … 2-4 preparing the installation site … 2-4 10Base-T connections … 2-4 Proactive Network tools fiber-optic, specifications …...

  • Page 75

    specifications connectors … A-2 telnet access to the console … 2-16 electrical … A-1 terminal configuration … 2-15 environmental … A-1 testing physical … A-1 checking the console messages … 3-8 safety … A-2 checking the LEDs … 3-8 straight-through cable diagnostic tests …...

  • Page 76

    VLAN effect on basic switch operation … 1-9 VT-100 terminal serial cable connection for … 2-16 wall mounting switch on … 2-13 6 – Index...

  • Page 80

    Technical information in this document is subject to change without notice. ©Copyright Hewlett-Packard Company 1998. All rights reserved. Reproduction, adaptation, or translation without prior written permission is prohibited except as allowed under the copyright laws. Printed in Singapore 12/98 Manual Part Number...

This manual also for:

Procurve 1600m, Procurve 2424m, J4120a

Comments to this Manuals

Symbols: 0
Latest comments: