Download Print this page

Landscape Forms Typology Installation Manual

Ring light, anchor kit and pole

Advertisement

Quick Links

Typology
Ring Light Anchor Kit and Pole
Installation Guide
Included components
12ft, 14ft,
16ft, 20ft
Pole height
1x – wooden drill template
Included: hardware is galvanized
12ft, 14ft, 16ft, 20ft (5in) pole: (4) anchor bolts, 3/4"-10 x 17" x 3" hook ,
(8) heavy hex nuts, 3/4" x 10, (8) flat washers, .81 ID" x 1.5" OD x 0.13" thick
25ft (5in/6in) pole: (4) anchor bolts, 3/4"-10 x 17" x 3" hook ,
(8) heavy hex nuts, 3/4" x 10, (8) flat washers, .81 ID" x 2" OD x 0.13" thick
Tools Required
• Safety glasses
• Wrenches, 1-1/4" for 4.5m, 6m or 8m (5in/6in) pole
• Level
LIGHTING LAYOUT RECOMMENDATIONS:
Refer to the product data sheet available at
recommendations for light pole spacing.
Landscape Forms is not responsible for site preparation and footings. The following
chart gives necessary information for calculating proper footing size, depending on the
specified light pole.
WARNING! Pole mounted luminaires must be attached before pole installation. Failure
to do so may cause vibration damage to the pole and will void the pole warranty.
Calculations per AASHTO 1994, assuming base of the pole is at grade level.
Pole Size
5" dia x .125" wall x 12ft
5" dia x .125" wall x 14ft
5" dia x .125" wall x 16ft
5" dia x .125" wall x 16ft
5" dia x .156" wall x 20ft
5" dia x .188" wall x 20ft
6" / 5" dia stepped x .188" wall x 25ft
25ft
Pole height
5in/6in dia
www.landscapeforms.com
for
Wind Speed
Max luminaires
110 mph w/ 1.3 gust
110 mph w/ 1.3 gust
110 mph w/ 1.3 gust
110 mph w/ 1.3 gust
100 mph w/ 1.3 gust
100 mph w/ 1.3 gust
100 mph w/ 1.3 gust
INSTALLATION PROCEDURE FOR ANCHOR BOLTS:
1.
Prepare footing as required by local codes.
2.
Install anchor hooks, hex nuts, washers and wooden template as shown in Fig 3. Level template
in all directions. Note: template thickness is less than base plate thickness. Dimensions given
account for the difference.
3.
After footing has properly cured, remove wooden template. Do not remove lower hex nuts or
washers.
HANDHOLE
ORIENTED ON
SIDE OPPOSITE
OF LUMINAIRE
[457mm]
18"
SIDEWALK
SETBACK
Fig. 1 – Sidewalk setback
Base Overturning
Moment (ft-lbf)
Base Shear (lbf)
1
1896
1
2382
1
2967
2
3485
2
4877
3
4923
3
7293
www.landscapeforms.com
Fig. 2 – Base plate
Fig. 3 – Anchor install detail, 5in or 6in pole
orientation
to luminaire
5" diameter pole
6" diameter base pole
Max luminaire
Max EPA (ft²)
223
1.64
248
1.64
276
1.64
316
2.58
372
2.58
369
3.52
434
3.52
Date: March 16, 2022
Ph: 800.521.2546
weight (lbs)
48
48
48
78
78
118
118
Page 1 of 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Typology and is the answer not in the manual?

Questions and answers

Summary of Contents for Landscape Forms Typology

  • Page 1 Refer to the product data sheet available at www.landscapeforms.com recommendations for light pole spacing. Landscape Forms is not responsible for site preparation and footings. The following chart gives necessary information for calculating proper footing size, depending on the specified light pole.
  • Page 2 Landscape Forms is not responsible for site preparation and footings. Refer to the Driver installation guide for the Typology Ring Light anchor kit for installing the anchor bolts. housing CAUTION! This unit is heavy. To avoid injury or damage to the finish, we recommend using a crane or lift for hoisting the unit onto the anchors.
  • Page 3: Installation Instructions

    14. Repeat luminaire install process for any remaining luminaires. TUBE 15. Lift the light pole into position over the installed anchors (refer to Typology Ring Light anchor kit installation guide) as shown in Fig. 9. Ensure that the base plate is resting on all four washers.
  • Page 4 Typology Ring Light Date: March 16, 2022 Installation Guide www.landscapeforms.com Ph: 800.521.2546 TWIST-LOCK OCC SENSOR Fig. 3 - Optional driver tube assemblies DRIVER LINE-IN WIRES HOUSING TUBE WIRING HARNESS TO LUMINAIRE GROMMET LINE-IN CONNECTIONS POLE ORIENT HOLES HOLE FOR KNOT...
  • Page 5 Typology Ring Light Date: March 16, 2022 Installation Guide www.landscapeforms.com Ph: 800.521.2546 PROTECTIVE HOLE FOR PADDING LUMINAIRE MOUNT DRIVER HOLE FOR ASSEMBLY LUMINAIRE MOUNT LOWEST LUMINAIRE Fig. 7 – Install lowest luminaire 3/8-16 x 1-1/2” SOCKET HD CAP SCREW LOCK WASHER FLAT WASHER Fig.
  • Page 6 Ph: 800.521.2546 PROCEDURE FOR WIRING RING: The Typology Ring light luminaire is assembled at the factory. The light cartridge is mounted into the head of the Ring and will not need to be removed during installation. Use of LED drivers other than the supplied unit is not recommended and will void the warranty.
  • Page 7 Typology Ring Light Date: March 16, 2022 Installation Guide www.landscapeforms.com Ph: 800.521.2546 WIRING DIAGRAM: double luminaire WIRING DIAGRAM: single luminaire, with occupancy sensor WIRING DIAGRAM: double luminaire, with twist lock WIRING DIAGRAM: double luminaire, with occupancy sensor Page 6 of 7...
  • Page 8 Typology Ring Light Date: March 16, 2022 Installation Guide www.landscapeforms.com Ph: 800.521.2546 WIRING DIAGRAM: triple luminaire, with twist lock WIRING DIAGRAM: triple luminaire WIRING DIAGRAM: triple luminaire, with occupancy sensor Page 7 of 7...