Related Manuals for Tiso FREEDOM
Summary of Contents for Tiso FREEDOM
- Page 1 «TiSO-PRODUCTION» LTD FULL-HEIGHT TURNSTILE «FREEDOM" Т1.1.ВYС.CC OPERATION MANUAL AUIA.481 ОМ 2018...
-
Page 2: Table Of Contents
CONTENTS С. INTRODUCTION..………….……………………….……………………….……..….. 3 1 DESCRIPTION AND OPERATION.……….…………………….…...…...…... 1.1 General Information and Purpose……………...……………...…..….… 1.2 Specifications………………..……………………………...……..……… 7 1.3 Configuration and Scope of Delivery...………..…….………….……..…..1.4 Revolving door design……………………….…........……. 2 INTENDED USE..……………………………………………………….…..……..10 2.1 Use limits ……………………….…………………..……………..…..…... 10 2.2 Layout and installation…….………………………..…………….…..…... 3 TRANSPORTATION AND STORAGE..……………………………..…..…. 25 4 DISPOSAL………………………………………..…….……………………...…..…. -
Page 3: Introduction
INTRODUCTION This operating manual (hereinafter referred to as "OM") applies to the turnstile of a full- height single-pass either internal or outdoor version without a servo (hereinafter referred to as "turnstile"). The OM contains information on the design, technical performances, installation, information for proper operation and maintenance of the turnstile. - Page 4 WARNINGS TO THE CUSTOMER ON SAFE OPERATION OF THE TURNSTILE These warnings are designed for ensuring of safety during operation of the turnstile to prevent violation of safety characteristics by improper installation or operation. These warnings are aimed at drawing attention of the customer to safety problems. GENERAL WARNINGS The Operation Manual is an integral part of the product and it shall be handed over to the customer.
- Page 5 Instructions to installer: 1. The equipment installation instructions shall be complied with for the purpose of safety. 2. The equipment shall be installed according to the code of practice and in compliance with safety gulations for installation. 3. The equipment shall be installed when it is deenergized. 4.
-
Page 6: Description And Operation
1 DESCRIPTION AND OPERATION General Information and Purpose 1.1.1 The motorized turnstile is designed for pedestrian movement control at access points of industrial enterprises, banks, stadiums, administrative facilities etc. by access control system (from keypad, proximity card readers)) or manually (from manual control panel). Traffic flow capacity of the turnstile with personal identification is at least 20 persons per minute in one direction .2 Turnstile's dimensions and weight correspond with the data presented in the... -
Page 7: Specifications
Table Continued In enclosed spaces in the absence of direct impact of precipitations and solar Installation site radiation Vertical, deviation from vertical position Operating position no more than 1º to any side is allowed 1.1.4 Reliability indices: - mean time to repair (without delivery time of spare parts, tools and accessories) – at most 6 hours;... - Page 8 1.3.2 Scope of Delivery The turnstile is delivered disassembled. The scope of delivery is specified in Table 4. Table 4 Product description Product designation/ parameters Quantity Note Full-Height T1.1.BYС.______ 1 kit. – Turnstile Components LED-lamps; 12 pcs. – Blunt bolt М5 х 10 ISO 4027 –...
-
Page 9: Revolving Door Design
1.4 Revolving door design Thermal curtain Canopy Rotor Handle Blade* Walls Frame * The door has three Y-shaped blades at 120 .angle. -
Page 10: Intended Use
INTENDED USE 2.1 Use limits 2.1.1 The turnstile must be used in the environment specified in p. 1.1.5 of this document subject to the specifications listed in section 1.2. IT IS FORBIDDEN: 1) TO MISUSE THE TURNSTILE (See section 1 "DESCRIPTION AND OPERATION");... - Page 11 2.2.3 Safety Measures: Installation to be performed only by the persons briefed on safety and studied this manual; Only serviceable tools to be used during installation of the turnstile; Connection of all cables to be performed only when power supply is OFF; ...
- Page 12 2.2.6 Revolving door assembly and installation steps Make sure that turnstile installation area is ready as follows: The installation site surface to be flat and horizontal; Thickness of concrete blinding coat under site to be at least 150 mm. turnstile fixation holes marked on the area surface according to...
- Page 13 3) The entrance and central posts to be inserted one after another into the frame base arcs and to be secured with screws M5.
- Page 14 4) The upper frame arcs to be placed on posts and to be fixed with screws М5х16; Screw M8 Washer M8 Nut M8 5) Two side segmental boxes installed on the frame in relation to the center post and to be fixed with screws M8;...
- Page 15 6) The rectangular beams with jumpers assembled Screw M8x60 connecting two sides of the Washer M8 turnstile frame by inserting Nut M8 them one after another into the appropriate slots of the previously installed side segmental boxes and to secured together with fastening screws as shown in...
- Page 16 8) The entrance segmental boxes with beams and frame jumper to be secured with additional crossbars by Screw M8x30 installing them into slots joining flush Washer M6 with the previously perpendicularly Nut M6 installed beam with screws providing robust scaffold of canopy. 9) Installation of side glass: - Rubber bands to be pulled on the frame arc outside part.
- Page 17 10) Container to be assembled according to the below diagram after the side glasses are installed: а) Container assembly: b) The container assembly with rotary drive to be attached to the installed beams on countersunk screws M6;...
- Page 18 c) Plumb bob to be hanged to check that center aligns with the mark made earlier on the floor and make sure that the door is perfectly leveled. The entrance and center post level to be checked) Centrality plumbing Checking of verticality with builder's level 11) The rotor support to be fixed according to center marks with anchors M8 and bottom disk to...
- Page 19 12) Rubber sealants to be installed and secured on canopy frame and space plate according to diagram: E type sealant 13) Each door to be assembled separately as follows:...
- Page 20 14) Installation of blades into revolving door: The installation to be repeat with the remaining two assembled blades (doors).
- Page 21 15) Crossbar bushing installation The revolver door has an access way locking function. For this one of three doors is equipped with a crossbar lock at the base. So, for access way locking function a hole next to access way to be made (See drawing below) and a bushing to be installed during installation.
- Page 22 16) Ceiling panels are installed by putting on pins: 17) The ceiling backlight (luminaires) to be installd and wiring to be pulled (See Annex В):...
- Page 23 18) Outside canopy segments to be installed: Silicone to be applied around segmental boxes; Silicone to be applied along overlap of sheets; The canopy side segments to be dropped flush one after another and then central segment; ...
- Page 24 19) Thermal curtain to be installed: Suspension space plate and cable entry to be provided; The curtain suspension to be secured with self- tapping screws М8 Thermal curtain to be installed on screws М8 ; Cable entry to be provided on-site...
-
Page 25: Transportation And Storage
3 TRANSPORTATION AND STORAGE 3.1 Turnstile storage It is forbidden to subject the turnstile to jerks and impacts during storage. Transportation trolleys to be used for handling of the turnstile. In storage facilities there should not be aggressive gases and vapours causing metal corrosion.. Air temperature during storage should not be below +50 С... - Page 26 5.6 The relationships between the Manufacturer and the Customer under the warrantyliabilities to be regulated by the applicable law of Ukraine, concluded purchase contracts andthese warranty liabilities. Manufacturer: LLC TiSO-PRODUCTION 14, Promyslova Street, Kiev, 02088, Ukraine Phone: +38 (044) 291-21-11 Tel./fax: +38 (044) 291-21-02 E-mail: sales@tiso.global...
-
Page 27: Annex А: Turnstile Design, Overall And Installation Dimensions
Annex А The product overall and installation dimensions are specified in Annex A... -
Page 28: Annex В Backlight Connection Diagram
Annex В Turnstile ceiling luminaire connection diagram Luminaire Inspection terminal box Inspection terminal box 220V connection terminal block...
Need help?
Do you have a question about the FREEDOM and is the answer not in the manual?
Questions and answers