1. Manuals
  2. Brands
  3. VOGE Manuals
  4. Motorcycle
  5. DS900X
  6. Operation manual

VOGE DS900X Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Far & Beyond Q uality
MOTORCYCLE OPERATION MANUAL
DS900X

Advertisement

Table of Contents
loading

Related Manuals for VOGE DS900X

Summary of Contents for VOGE DS900X

  • Page 1 Far & Beyond Q uality MOTORCYCLE OPERATION MANUAL DS900X...
  • Page 2 This book is a part of the motorcycle, keep it always on the vehicle even sell or lend. VOGE...

  • Page 3: Table Of Contents

    Weak engine power......53 Installation and usage instructions for VOGE Global APP ..
  • Page 4 Grinding-in for engine..... . 54 Disassemble and re-assemble batter y ..66 Grinding-in for tire ......55 External power supply .

  • Page 5: I.issues Need Pay Attention To

    I.Issues need pay attention to This user manual has the warning marks as below, when you saw it, please follow these driving and maintenance procedure. Danger This mark indicates it may lead to bad injury even death. Warning This mark indicates it may lead to damage on motorcycle. Caution This mark means more effective and convenient point for driving.

  • Page 6: Ii.safe Driving

    Please always adopt origin VOGE parts or our authorized ones. The parts nor from VOGE factory, inco rrect accessories or loading are bad for motorcycle performance even break laws, please take responsibility for your safety and that of others.

  • Page 7: Checking Before Driving

    Checking before driving Before driving,make the inspections as below to reduce accident or damage: •Steering system •Tires •Horn -Handle bar turns freely Correct tire pressure. Normally works. without jamming. Without too much abrasion •Kill switch of engine -No run-out or flexibility for depth of tire tread.

  • Page 8: Issues Need Pay Attention To During Driving

    Issues need pay attention to during driving 1.Any driver must know well about the motorcycle, the incorrect sitting position or off set during driving may be bad for operation or control of motorcycle; When driving, the passenger need. stably sit on his seat without influence driver. Passenger is an animal is not allowed.

  • Page 9: Driving On Road

    Driving on road •Get on the motorcycle from left side and ride on. •Pick up the side stand. • Get the motorcycle upright to the ground, get the handle bar face front, keep its wheel face forward. • Tightly hold the clutch lever. •...

  • Page 10: Braking And Parking

    Braking and parking •Please decelerate first when braking to reduce the speed and use the front and rear brake at same time. •When the driving speed is low enough, get into low gear position, and tightly hold clutch lever. • Get the engine into neutral gear, the motorcycle brakes and completely stops.

  • Page 11: Iii.main Parameters

    Ⅲ. Main parameters Parameters for motorcycle Engine parame te rs L x W x H 2325mm x 940mm x 1420mm Engine type Twin-cylinders in line/Water cooled/4 valves Wheelbase 1580mm Bore x stroke 86mm x 77mm Seat height 825mm Displacement 895ml Ground clearance 190mm Compression ratio...

  • Page 12: Iv.structure Of Motorcycle

    Ⅳ. structure of motorcycle Identification for motorcycle Th e Vehicle Id entific ation Number (VIN) and name plate Engine typ e number an d Delivery n umber Engine type and Delivery number Vehicle Identification number Products number...

  • Page 13: Head Part

    Head part 1. Left handlebar cover 2. Left rearview mirror 3. Left brake lever switch 4. Instrument 5. ignition switch 6. DC socket 7. Front brake oil cup 8. Right brake lever switch and fuel dispenser seat 9. Right rearview mirror 10.

  • Page 14: Left Side

    Left side 1. Headlight/front position lamp 2. Left front turn signal lamp 3. Rearview mirror 4. Fuel tank 5. Oil filler and dipstick 6. Quick trend shifter 7. Main seat cushion 8. Left rear turn signal lamp 9. Brake light/rear position lamp 10.

  • Page 15: Right Side

    Right side 1. Passenger armrest 2. Pressure regulating rectifier 3. Rear brake oil cup 4. Right bumper 5. Right front turn signal 6. Right front fog light 7. Right reflector 8. Front disc brake disc right 9. ABS ring gear 10.

  • Page 16: Lower Side Of Seat

    Lower side of seat 1. Start relay 2. IMU controller (some models have it) 3. Battery 4. Dash cam (some models have it) 5. Electronic controller ECU 6. Diagnostic interface 7. BCM controller 8. Seat cushion lock 9. fuse box 10.
  • Page 17 Schematic diagram of insurance and control relays Sea t c us hi o n hea ting d rive F og L a m p Sea t c u sh ion Sw itc h hea t ing s w itc h o r an g e 2B lu e and yel lo w...

  • Page 18: V.operation

    Ⅴ.Operation Ignition switch The ignition switch of this model is on the upper connective plate. This model equipped one key (Include a mechanical key, on the remote control key, the left button is for searching, short press is searching, the turning signal of model flashes 10 times, in the open field, the distance for searching is 30m, in case not in open field, its distance may be shorter than 30m), this model also equipped a spare key, please keep the spare key in place separately.
  • Page 19 12.Troubleshooting for ignition switch. (1)Failure of motorcycle power on. When short press ignition switch, check the reminder from indicating lights of ignition switch and remote key. The red light flashes for 3 times on ignition switch means feeling failure for key, whose possible causes are: -The distance from remote key to ignition switch is longer than 1.3;...

  • Page 20: Instrument And Its Indicating Light

    Instrument and its indicating light 1. Left turn indicator light 2. High beam indicator light 3. Battery voltage warning light 4. Engine malfunction warning light 5. Environmental low temperature indicator light 6. Front fog light indicator light 7. Bluetooth connection display 8.
  • Page 21 When pressed button of ignition switch, the meter get power on and start self-inspection: The display screen gets on and start self-inspection, show you the situation of motorcycle at the moment. When engine is in malfunction, the alarm light" "gets on; The alarm light for ABS malfunction" "...
  • Page 22 TCS is working, while its indicator light " " is fast flashing. Warning When TCS is on and during driving, in case its indicator light " " keeps steady on, which means there is malfunction in TCS system, under this situation, please contact dealer under VOGE immediately.
  • Page 23 Right turning signal light" " When pushing the turning signal switch " " to right, the turning signal light " " gets on. Caution When the turning signal light on motorcycle damaged or failure caused by other malfunctions, the flashing frequency of this turning signal light "...
  • Page 24 The receiver for signal from tire pressure only works when engine started, in case no signal received, the meter may show you the white cross bar. The meter shows you the last data of tire pressure. In case the driving speed is lower than 25km/h, the tire pressure the meter shows you may not the actual one, if there is change of tire pressure during this period, the actual tire pressure may not reflect on meter, for example parking, air charge or discharging, whose latest tire pressure may not reflect onto meter immediately, only when the driving speed was higher than 25km/h, the data for tire pressure will...
  • Page 25 Displaying screen of TFT When the meter is working: When it starts working, it shows you the setup for mode information of last time. Light for background of meter: The meter shifts its light of background according to brightness. Bluetooth connection: When the cell phone is connected through Bluetooth to meter, the icon of Bluetooth is lighting and could show you caller ID (Show you caller ID + Caller name).
  • Page 26 Caution The fuel level may get waving during driving, when there is not so much residual fuel, it may lead to indicating bar flashing or sometimes not, which is normal situation, please don’t worry. In case the alarm light for fuel level got amber, it means there is only about fuel of 3L in fuel tank.

  • Page 27: Installation And Usage Instructions For Voge Global App

    1.1 Apple download: 1.1.1 Scan the QR code above by iphone camera, when successfully ldentified, click links to get to store for downloading. 1.1.2Enter the iphone App Store to search for" VOGE Global" ,and download. 1.2 Android download 1.2.1 Open " Google" of Android cell phone itself,then click the button of camera in Search bar, scan by camera, when successfully recognized, it gets to store for downloading automatically.
  • Page 28 3.VOGE Global Map configuration 2.5 Enter token name and select 3.1 Open VOGE Global, then open Setup->Map configuration->Map applicationscopes,then click on configuration guidance->Fill blanks for Mapbox Token. (User needs “create token”.(See Figure 4) to apply for Mapbox Token and fill blanks, otherwise the navigation 2.6 Enter the confirmation password to...
  • Page 29 4. Use for basic navigation of Bluetooth(TFT screen) 4.1 Get motorcycle power on, open setup for cell phone->Bluetooth, Select Bluetooth name of (VOGE-) as beginning, when successfully connected, allow to visit phonebook, when connected, the instrument will show you the icon of (Bluetooth 1).
  • Page 30 5. The use of driving recorder 5.1 Open the VOGE Global, click [Fuel meter connection] then get into main page of APP, click the icon of camera on the left, get into main page of DVR;...
  • Page 31 5.2 Click [Add equipment] in main page of DVR, then confirm 5.4 Click [Recorder] in main page, then shift back to main connection according to reminder, then find out recorder net with page of recorder;(See Figure 7) beginning of mt in WLAN in setup of mobile phone, then add it in; 5.5 When recorder was connected in main page of DVR, click once again the icon for adding equipment to get into page for recording video at real time;(See Figure 8)
  • Page 32 5.6 In the page for recording video at real time, click [Recorder Video] to open the list of video, click it to get into video playback; Figure 9 Figure 10 Caution ·The interface of APP and is function may change with update of upgrade of UI, the final interface and function for using is the same with latest downloaded version of 5.7 In the page for recording video at rear time, click...

  • Page 33: Introduction For Instrument Operation

    Introduction for instrument operation (1). There are 4 driving modes for this model, which are ROAD, RAIN, 1.Introduction for buttons SPORT, and ENDURO, whose shift are shown as below: (1.1). When the motorcycle is not in moving, short press mode switch, the Up-key modes ROAD, RAIN, and SPORT could be shifted at will.
  • Page 34 ） （2 2.Bluetooth connection .Bluetooth connection Search the Bluetooth name nearby as picture above shows, (1)Bluetooth name display when connected, the Bluetooth sign on meters lights up, at Short press down key to get into display page for this moment, the meter can show you the caller ID. Bluetooth name, press key return to get back to main page;...
  • Page 35 Get into the 1st menu, press key up or down to select My motorcycle, then press key confirm to get into page selection, when the cursor selected page, press key confirm of Get into My motorcycle Next page or Previous page for shifting circulation, when the cursor selected return, press key return to get back to previous page.
  • Page 36 When got into 2nd menu, press key Up or Down to select language, press key confirm to get into language selection, press key Up Language selection or Down to shift English, Esoanol or Italiano, get cursor on the item you want, then press key confirm to select, then press key return to confirm and get back to 2nd menu.
  • Page 37 When got into 2nd menu, press key Up or Down to select 0 clear for mileage sub- total, press key confirm to get into 0 clear for mileage sub-total, get cursor on the item 0 Clear for mileage sub-total you want, then press key return to get back to previous page, then get cursor on key return and press it to get back to 2nd menu.
  • Page 38 When got into 2 menu, press key Up and Down to select Bluetooth connection, press key Up and Down to get shift on Bluetooth connection or off, get cursor on the item you want, then press key return once again to get back to 2 menu.
  • Page 39 When got into 2 menu, press key Confirm, get in and open the selected item, press key Confirm for selecting, press key Down to off, press key Confirm to select, press key Down to select gear position, when key confirm pressed, press key Up and Down to confirm suitable gear position, press key Confirm, press key Down to select reduce gear the hundred place for rotation speed in reminder, when key Confirm pressed, when pressed key Up and Down to confirm suitable rotation...

  • Page 40: Steering Set Switch

    Steering set switch 1. Clutch handle 2. High and low beam, overtaking switches 3.Grip heating up button 4.Seat heating up button 5. Emergency light button 6.Driving recorder snapshot button Some models equipped with 7. Front brake handle 8. Front fog light switch 9.
  • Page 41 High beam/Overtaking light switch This model doesn’t equip a switch for low beam only, when the motorcycle is power on, the low beam is off, in case push forward or pull backwards the high beam/overtaking switch, or when engine is working, the low beam will be on automatically until engine gets off or voltage is lower than 12.5V.
  • Page 42 Turning signal light When pushed turning signal switch on left switch assembly to left side " ", the both front and rear turning signal light on left get on, meanwhile its corresponding indicator light " " on meter also gets on. When pushed turning signal switch on left switch assembly to right side "...
  • Page 43 Cruise control " " There are speed adjusting key and switch key for cruise control, turn the switch key left to get cruise control function start or stop, when pushed switch forward RES/+, the cruise speeds up by 2km, when pulled backwards SET/- , the system sets "...
  • Page 44 ROAD automatically. Snapshot button " " for driving recorder When the Voge Global APP didn’t connect, short press the Snapshot button for driving recorder on right switch assembly, " " you can take photo, then the photo will store in card of Micro SD(TF).

  • Page 45: Socket For Usb Power Supply

    Danger In case turned kill switch to position " " during driving may make rear wheel suddenly lock up even accident. Socket " " for USB power supply This model equipped power supply socket for USB, according to different Mobile phone’s User Agreeme nt, the ones for one-way match up with 18W(5V3A, 9V2A, and 12V1.5A);...

  • Page 46: Abs System

    ABS system 1.Deceleration and braking under normal situation, release the throttle first, tightly hold the han dle bar and then brake. When driving speed fell, to avoid engine stop working, hold clutch lever to get into low gear position. 2.Decelerate before turning, when passing the turning, do everything possible to keep an even speed, in case it is needed, slightly brake, the sudden braking is forbidden.

  • Page 47: Tcs Traction Control System

    TCS traction control system Confirm sliding difference according to differential device, compare the wheel speed for front and rear wheel. Then confirm stable surplus for rear wheel. In case the sliding difference was exceeded, the control system of engine will adjust torque from engine.

  • Page 48: Cruise Control System

    Cruise control system The display area for cruise control only shows you the current speed for cruise. When the driving speed is higher than 40km/h, while the gear position is between to 6, in case turned on the button for cruise control and it works, the speed for cruise could be kept without operate accelerator.

  • Page 49: Radar (Some Model Equipped)

    2.Some warning doesn’t work. work please contact to local dealer of 3.It may give you warning even blind or near area is without other vehicle. VOGE. Some special condition includes but not only: Bad weathers (Such as rain, snow or thick fog);...
  • Page 50 In case too big the deviation, it is bad to normal working of radar or reduce its performance, such as accident or motorcycle rolling over, replace or disassemble components of radar may also produce deviation against initial position at delivery of factory. Once big deviation is found, please contact local dealer of VOGE immediately.

  • Page 51: Gearshift Device

    Gearshift device This model equipped gearshift device with 6 gear positions, whose gearshift details are shown as below: Step down Kick up Gearshi ft pedal •The gearshift device makes engine stale work within normal rotation speed. •Gearshift ratio is carefully designed according to engine performance, the driver shall select the most suitable gear position, please don’t drive in high speed while in low gear position.

  • Page 52: Side Stand And Main Stand

    Side stand and main stand The design for this model includes both side stand and main stand. Kill switch on side stand is a design for safety, which is a part in starting circuit of engine. Rear brake pedal Step down rear brake pedal, the rear wheel Kill switch on Rear brake side stand...

  • Page 53: Engine Starting

    Engine starting The side stand ls laid down. Press button of ignition switch. Confirm if the engine is in neutral, the indicator light " N " for neutral gear on meter may get on. Once conditions above got ready, tightly clasp clutch lever by left hand for ensure safety, the right hand press electric starting button "...

  • Page 54: Fuel Filling-Up

    Danger The exhasut gas of motorcycle has carbon monoxide, which is without color, smell, but poisonous. In the place without smooth ventilation or indoors, start engine for idling too long is not allowed , to avoid poisoning. Fuel filling-up Reminder for low residual fuel level This alarm light reminds you fuel filling-up Caution: In case the fuel is not enough, it leads to engine starting failure, or abnormal power out put, under this case, keep driving will damage fuel pump.
  • Page 55 Warning ·The fuel is corrosive to painting surface, get its color fading and ugly. In case there is fuel on the painting surface, please wipe it up. · The fuel may expand when it is hot, fully fill up may lead to overflow due to too strong the internal pressure makes fuel tank distort.

  • Page 56: Ⅵ.malfunctions

    - n case too low the coolant level, please fill up with coolant. -In case the alarm light for coolant temperature got on while the electric fan of heat radiator doesn’t work, please contact service station nearby for troubleshooting, the best way is contact local dealer of VOGE. Insufficient coolant In case coolant was not enough or the heat radiator is blocked by stand or stone, we suggest the way as below: -Reduce loading of motorcycle to reduce heat produced by engine.

  • Page 57: Engine Starting Failure

    Incorrect check and adjustment may damage your motorcycle and let you fail to find out the malfunction, which can’t get the service of Quality Guarantee. In case you don’t know much about the correct operation, please conta ct the VOGE dealer.

  • Page 58: Grinding-In For New Motorcycle

    Ⅶ.Grinding-in Grinding-in for new motorcycle The grinding -in period is important to working life and fuel consumption, so before driving, read the User Manual carefully. (The correct driving within the first 1000km is good for motorcycle performance and bring you fun of driving. Grinding-in for engine •No matter the engine is hot or cold, before starting, idly start the engine for enough time, to let oil spread to all positions need lubrication.

  • Page 59: Grinding-In For Tire

    Grinding-in for tire • The surface of new tire is smooth, so it is dangerous to driving too fast or at turning. To get the strongest gripping force, the grinding-in is important. •In the first 200km, you can drive at turning in low speed until all angles of tire tread completely grinded-in. •The protrusion on tire tread is dangerous, the grinding is a good way for avoid protrusion on tire tread.

  • Page 60: Adjustment For Clutch Lever

    Adjustment for clutch lever •When engine started, in case need braking or gear shift, tightly hold clutch lever to let friction plates of clutch separate to cut off the power transmission from engine. •The free play at end of clutch lever shall be within 5-8mm, in case it is incorrect, please adjust as below: -Remove the rubber jacket -Loosen locking nut 1...

  • Page 61: Adjustment For Rear Brake Pedal

    When re-assembled, repeatedly press and release brake pedal, while confirming you can clearly feel the pressing point. In case pressing point failed to be felt, please contact VOGE dealer. In case adjustment is not correct, the brake pad and plate are always under stress, which may lead to their...

  • Page 62: Adjust Front Shock Absorber

    Adjust front shock absorber Adjust the pre-load and damping load for front shock absorber is to suit different drivers, loadings, driving habits and road conditions. The pre-pressure of spring is adjustable. -Turn the adjustor 1 anticlockwise, the pre-loading of spring gets soft. -Turn the adjustor 1 clockwise, the pre-loading of spring gets hard.

  • Page 63: Adjust Rear Shock Absorber

    Adjust rear shock absorber The pre-pressure for spring is adjustable. Face to the right side of motorcycle, turn the adjustor 1 anticlockwise, the pre-loading for spring gets soft. Face to the right side of motorcycle, turn the adjustor 1 anticlockwise, the pre-loading of spring gets hard. Driving mode of driver only without loading: Turn the djustor 1 anticlockwise to limit, then turn it clockwise by 6 positions (Position of delivery time);...

  • Page 64: Adjustment For Headlight Dimmer

    Danger Please don’t adjust pre-pressure for rear shock absorber at will, improper adjustment may reduce your control on motorcycle, in case adjustment is needed, please contact dealer of VOGE authorized. Adjustment for headlight dimmer •All the height of headlight must be correct under any loading of shock absorber.

  • Page 65: Adjustment For Transmission Chain

    Adjustment for transmission chain •Too tight or loose the chain are both incorrect. •Too loose the chain, it may cause the chain drop during driving then lead to accident. •Too tight the chain is bad for its working life, meanwhile increase 35~45(mm ) resistance for power transmission.

  • Page 66: Ⅸ.check, Repair And Maintenance

    Ⅸ.Check, repair and maintenance The fuel The fuel parameter when you purchasing the motorcycle is the most fuel saving way or under a fixed speed, which is quite different to your actual driving, which may be higher than the fuel parameter for reference only. •The operations below may decrease the fuel consumption under correct driving: –The driving shall be gentle, stable and without sudden braking as possible, the re-start and accel eration may use more fuel.

  • Page 67: The Fuel Evaporation

    The fuel evaporation When the fuel evaporation system gets failed, please contact the VOGE service station. Refit on fuel evaporation system is not allowed, otherwise the emission may not meet the standard. After removal and repair, check the connection of tube joint, leakage of pipeline, or block;...

  • Page 68: Tool Kit

    Maintenance for battery please contact service station of VOGE, make sure the added The battery on this model is completely free electrical device use the reserved joint on original motorcycle.
  • Page 69 The power charge for battery In case the ignition lock is off, while the voltage of battery is lower than 12.6V, we suggest charge the battery. •Charge the battery by stable DC power source or use the suitable power charger and strictly follow its instruction. Danger •The DC charging voltage shall be DC (14.5±0.3)V with stable current no more than 1A;...

  • Page 70: Disassemble And Re-Assemble Battery

    Disassemble and re-assemble battery Before disassembling or re-assembling battery, please turn off ignition switch first, Warning then get the motorcycle power off. When disassembling battery, remove negative terminal first, then the positive one. Don’t put the battery up side When re-assembling battery, assemble positive terminal first, then the negative one. When disassembling battery, before taking it out, turn the bolt onto battery first, to down, otherwise the electrolyte avoid nut dropping off during removal of battery.

  • Page 71: Maintenance For Air Filter

    Maintenance for air filter •The air filter locates under fuel tank, if it is blocked by dust, the air inlet may get harder, which reduce power output and increase fuel consumption. • In case driving under dusty condition, clean up and replace the element more frequent. •...

  • Page 72: Oil In Engine

    Oil in engine Check the oil level • The oil inspection window and filling up port are both at the right cover of engine. • The checking for oil level: –Do this work when the engine is cold. –Keep the motorcycle upright. –Remove the oil gauge 1 to check the oil level.
  • Page 73 •Outlet the oil: –In case too high the oil level, please remove the oil drainage bolt by socket wrench,the oil drainage bolt is at the middle place of engine bottom (Picture 1). –After releasing an appropriate amount of engine oil, please reset and lock the engine oil bolts.
  • Page 74 Replacement for engine oil • Replace the engine oil when maintenance period reached. • Replace the oil when engine is hot to totally drain off the old oil. • The replacement for oil: Start engine. Stop engine. Screw off the oil gauge, remove oil drainage bolt and washer on oil bottom case, then drain the oil off.
  • Page 75 Oil filling up for engine •Confirm the oil element already replaced and its cover already assembled. • Confirm the oil drainage bolt and gasket are both replaced and re-assembled. • Add new engine oil from the oil filling port,The capacity for oil filling-up is 3000mL (In case the secondary oil filter needn’t be replaced, the capacity for filling-up is 2800mL, in case break up the crankcase for a total maintenance, the capacity shall be 3200mL) •Start the engine to let it idly run for seconds.

  • Page 76: Replacement Of Oil Filter

    Get main stand holding the motorcycle. • • • • • • Warning Check the gasket on cover of oil element, replace for a new one if it is necessary. A wrong oil element may damage the engine, please surely adopt the origin VOGE parts.

  • Page 77: Coolant

    When the expansion tank is totally dried up, don’t fill up coolant by yourself, because under this case, the air may already get into the cooling system and need to be exhausted, so please contact the VOGE dealer for maintenance.
  • Page 78 The replacement for coolant •The coolant drainage: –Keep the motorcycle upright by standing rack. –Lay a liquid tray under the engine. –Remove the water drainage bolt, because all the heat radiation system is connected, so all the coolant may flow out from this port. –After the old coolant is completely drained, replace the flat gasket and install the drainage bolt back.
  • Page 79 •In case the air temperature is lower than the one marked up on the label, please adopt the coolant fits for lower temperature. • The VOGE coolant is with ice point of -45°C of glycol so we suggest purchase or replace by Made in VOGE. Caution •To keep the coolant performance, replace each two years.

  • Page 80: Brake Liquid

    LOWER or MIN UPPER or MAX LOWER or MIN yourself may let air and moisture in, which largely reduce the braking performance even failure, so please contact VOGE dealer to do this work. The specification of brake liquid Caution •When there is impurity or moisture in the brake liquid,...

  • Page 81: Driving Chain

    The driving chain for this model is the one with oil seal, the place of chain’s pin has a special oil seal for sealing lubricant, this chain is the one without opening, so in case replacement is needed, please contact VOGE dealer.

  • Page 82: Tire

    Tire The tire connects the motorcycle and ground, it is very important, the incorrect specification and status is very bad for motorcycle performance. The tire pressure in tire Danger •The wrong tire pressure makes its working life shorter. The incorrect tire pressure is not only bad for •...
  • Page 83 •Seal the contact position between the wheel rim and tire lip of tubeless tire. •To avoid air leakage, the tubeless tire needs special tool and machine for disassembly and re-assembly. •The tire replacement need be done by VOGE dealer, they are skillful and with necessary tools or ma chine.

  • Page 84: Fuse Chip

    Fuse chip - Fuse for power charger(10A) - Fuse for control signal(25A), braking light, BCM, meters, kill switch, horn, and power supply for USB. - Fuse for power supply of motor of ABS (25A): Power supply for motor of ABS system.

  • Page 85: Relay

    Caution In case the fuse chip usually burns out in short time, which indicates there is malfunction in elec trical system, please contact the VOGE dealer immediately. Danger •Please use the fuse chip with given specification, substitution such as aluminum sheet or iron wire are not allowed.

  • Page 86: Brake Pad

    For the reliability for braking, the abrasion passed Min. thickness limit is not allowed. Replacement for brake pad The correct replacement needs to remove the wheels, so this work shall be done by VOGE dealer. No matter the front or rear brake pads, replace...

  • Page 87: Replacement For Lighting Signal

    Replacement for lighting signal •If there is no light signal, you may be in danger, because the light helps others easily pay attention to you and your motorcycle. Please replace the broken lights. The headlight, front position light, turning signal light, rear position light, brake light and registration plate light are all LED and sealed, in case broken, go to the service station for replacement.

  • Page 88: Maintenance Plan

    Maintenance plan The table below shows you the inspection for each periodic maintenance, whose interval of time and mileage, set whom reached first as standard, and make the inspection as table below every time. Period table for maintenance Items Km x 1000 Interval Oil in engine Oil filter...
  • Page 89 •After a long driving in sandy weather or muddy road, the special maintenance is necessary. •We suggest this kind of work shall be done by VOGE dealer. •Correctly dispose the abandoned materials such as cleanser or waste oil, don’t let them to be pollutions.

  • Page 90: Ⅹ. Maintenance For The Motorcycle In Long Parking

    Storage for motorcycle •In case the motorcycle needs to park for a period without driving, the special maintenance is nece ssary, which need some special tools, equipment or technologies, because of this, we suggest these works shall be done by VOGE dealers.

  • Page 91: Protection For Motorcycle

    Protection for motorcycle •According to the daily driving, usually wash the motorcycle and keep it clean and dry. •Wash up the dirt, bird shit, asphalt or salt on motorcycle surface as quick as possible. •Try best to cover the motorcycle by dry cloth, long time exposed under sunshine may make covering parts get aged or color fading.

  • Page 92: Xi. Electrical Diagram

    XI. Electrical diagram CA N -H CAN - L turn right CANH CAN L Seat cushion heating drive Fog Lamp Seat cushion heating switch Switch orange 2Blue and yellow ambient Confirm temperature down key High bean Right warning light PCANH PCAN L CANH CANL...
  • Page 93 Facebook www.vogeglobal.com...

Table of Contents