Page 2
Edition Notes The Intimidator Beam 360X User Manual includes a description, safety precautions, installation, programming, operation, and maintenance instructions for the Intimidator Beam 360X as of the release date of this edition. Trademarks Chauvet, Chauvet DJ, the Chauvet logo, and Intimidator are registered trademarks or trademarks of Chauvet &...
Important installation or configuration information. The product may not function correctly if this information is not used. Useful information. Intimidator Beam 360X User Manual Rev. 1...
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and the user. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Intimidator Beam 360X User Manual Rev. 1...
6 Power in 7 Power out 8 Fuse holder 9 DMX in 10 DMX out 6 7 8 9 Product Dimensions 16.9 in 429 mm 12.7 in 8.7 in 322 mm 220 mm Intimidator Beam 360X User Manual Rev. 1...
It is possible to link up to 9 Intimidator Beam 360X products on 120 VAC or up to 15 products on 230 VAC. The power linking diagram shown above corresponds to the North American version of the product ONLY! If using the product in other markets, consult with the local Chauvet distributor as power linking connectors and requirements may differ by country or region.
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Intimidator Beam 360X may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming.
Press to scroll down the list of options or to find a lower value <ENTER> Press to activate a menu option or a selected value Menu Map Refer to the Intimidator Beam 360X product page on www.chauvetdj.com for the latest menu map. Main Level...
Temperature: _ _ _ Displays the current product temperature DMX Configuration The Intimidator Beam 360X works with a DMX controller. Information about DMX is in the Chauvet DMX Primer, which is available from the Chauvet website chauvetlighting.com/downloads/ DMX_Primer_rev05_WO.pdf. Starting Address The Intimidator Beam 360X uses up to 14 DMX channels, which defines the highest recommended address to 499.
DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Automatic Programs To run the Intimidator Beam 360X in automatic mode, follow the instructions below: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Run Mode.
6. Use <UP> or <DOWN> to increase or decrease the value of the selected function, from 000–255 (functions work the same as in DMX mode). 7. Press <ENTER>. 8. Repeat steps 4–7 until the selected step is set as desired. Intimidator Beam 360X User Manual Rev. 1...
6. Use <UP> or <DOWN> to select OFF (normal display orientation) or ON (reverse display orientation). 7. Press <ENTER>. Pan Angle To set the pan angle range on the Intimidator Beam 360X, follow the instructions below: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Setup. 3. Press <ENTER>.
6. Use <UP> or <DOWN> to select OFF (normal range of motion), UP (upward tilt range), or DOWN (downward tilt range). 7. Press <ENTER>. DMX Loss To set how the Intimidator Beam 360X will respond to losing a DMX signal, do the following: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Setup. 3. Press <ENTER>.
4. Use <UP> or <DOWN> to select RF. 5. Press <ENTER>. 6. Use <UP> or <DOWN> to select from RF 1–4 (sets an RF group for the Intimidator Beam 360X), or RFP (enables the fixture to respond to all RF signals).
The RFC remote will not respond to any inputs when Freeze or Black Out is activated. If the remote does not respond when a button is pressed, try pressing <FREEZE> or <BLACK OUT>. Freeze or Black Out may have been inadvertently activated. Intimidator Beam 360X User Manual Rev. 1...
Operation Zero Adjust Mode The Intimidator Beam 360X contains a passcode protected mode which allows the user to calibrate and adjust several of the product’s operating parameters. In order to access this mode, do the following: 1. Press and hold <MENU> for at least 3 seconds.
7. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. Do not spin the cooling fans using compressed air because they could be damaged. Intimidator Beam 360X User Manual Rev. 1...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. Intimidator Beam 360X User Manual Rev. 1...