Electronically published by Chauvet in the United States of America. CHAUVET, the Chauvet logo, and Intimidator Beam Q60 are registered trademarks or trademarks of Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.
Keep this User Manual for future use. If the product is sold to someone else, be sure that they also receive this document. Page 2 of 19 Intimidator Beam Q60 User Manual Rev. 1...
WARNING! DO NOT plug anything other than a data connection into the USB C port. Doing so may cause damage to the product. Product Dimensions 12.6 in 320 mm 8.8 in 5.9 in 224 mm 149 mm Intimidator Beam Q60 User Manual Rev. 1 Page 3 of 19...
3. Setup AC Power The Intimidator Beam Q60 has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Intimidator Beam Q60 may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
Press to scroll down the list of options or to find a lower value <ENTER> Press to activate a menu option or a selected value Menu Map Refer to the Intimidator Beam Q60 product page on www.chauvetdj.com for the latest menu map. Mode...
Temperature: _ _ C Displays the product temperature in °C Configuration (DMX) The Intimidator Beam Q60 works with a DMX controller. Information about DMX is in the CHAUVET DMX Primer, which is available from the Chauvet website http://www.chauvetlighting.com/downloads/ DMX_Primer_rev05_WO.pdf. Starting Address When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses.
Page 11
176 183 Pan and tilt reverse spin 184 191 Pan forward spin and tilt reverse spin 192 199 Pan reverse spin and tilt forward spin 200 255 Reserved for future use Intimidator Beam Q60 User Manual Rev. 1 Page 9 of 19...
215 255 R: 100–0% G: 0% B: 100% W: 0% 000 255 0–100% Green 000 255 0–100% Blue 000 255 0–100% White 000 255 0–100% Page 10 of 19 Intimidator Beam Q60 User Manual Rev. 1...
Page 13
176 183 Pan and tilt reverse spin 184 191 Pan forward spin and tilt reverse spin 192 199 Pan reverse spin and tilt forward spin 200 255 Reserved for future use Intimidator Beam Q60 User Manual Rev. 1 Page 11 of 19...
4. Use <UP> or <DOWN> to select Sound. 5. Press <ENTER>. Sound Sensitivity To set the sound sensitivity on the Intimidator Beam Q60, follow the instructions below: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Setup. 3. Press <ENTER>.
6. Use <UP> or <DOWN> to select from 540 (540°), 360 (360°), or 180 (180°). 7. Press <ENTER>. Tilt Angle To set the tilt angle range on the Intimidator Beam Q60, follow the instructions below: 1. Press <MENU>. 2. Use <UP> or <DOWN> to select Setup.
The Master/Slave mode allows a single Intimidator Beam Q60 product (the “master”) to control the actions of one or more Intimidator Beam Q60 products (the “slaves”) without the need of a DMX controller. The master product will be set to operate in standalone mode, while the slave products will be set to operate in slave mode.
Operation Zero Adjust Mode The Intimidator Beam Q60 contains a passcode protected mode which allows the user to calibrate and adjust several of the product’s operating parameters. In order to access this mode, do the following: 1. Press and hold <MENU> for at least 3 seconds.
7. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. Do not spin the cooling fans using compressed air because it they could be damaged. Page 16 of 19 Intimidator Beam Q60 User Manual Rev. 1...
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. Chauvet reserves the right to use its own discretion to repair or replace returned product(s). Page 18 of 19 Intimidator Beam Q60 User Manual Rev. 1...
Visit the applicable website above to verify our contact information and instructions to request support. Outside the U.S., U.K., Ireland, Mexico, France, Germany, or Benelux, contact the dealer of record. Intimidator Beam Q60 User Manual Rev. 1 Page 19 of 19...