Erasing A Cd-Rw Disc - Yamaha CDR-HD1300 Owner's Manual

You can erase the data recorded on a CD-RW disc. New recordings can be made in the space created by erasing. The following 4 types of
erasing are possible with this unit.
I Last Track Erase
This operation erases the last track on a disc. "Last Track Erase"
cannot be performed if a CD-RW disc has been finalized, or only
one track has been recorded on the disc.
1.
Load the CD-RW disc to be erased.
2.
Press ERASE.
The following message appears on the display.
Go to the next step when erasing only the last track. To erase
other tracks as well, select the track number to start erasing
from by rotating the MULTI JOG knob.
Track to start erasing from
To cancel erasing, press a.
3.
Press w/d (w on the remote control) to start erasing.
"Erasing" flashes on the display, and the level meter shows the
erasing progress.
4.
This unit enters the stop mode when erasing has
been completed.
I All Track Erase
This operation erases all tracks recorded on a CD-RW disc. TOC
will be erased also if a CD-RW disc has been finalized.
1.
Load the CD-RW disc to be erased.
2.
Press ERASE repeatedly until "Erase ALL ?" appears
on the display.
To cancel erasing, press a.
3.
Press w/d (w on the remote control) to start erasing.
"Erasing" flashes on the display, and the level meter shows the
erasing progress.
4.
This unit enters the stop mode when erasing has
been completed.

ERASING A CD-RW DISC

TRACK
L
dB –30 –10 –6 –2 0
CDRW
R
TRACK
L
dB –30 –10 –6 –2 0
CDRW
R
Last track
L
dB –30 –10 –6 –2 0
CDRW
R
I TOC Erase
This operation is only available on a CD-RW disc that has been
finalized. After the Table of Contents (TOC) has been erased, the
effects of finalization are defeated, and further recording is
possible.
1.
Load the CD-RW disc that has been finalized.
2.
Press ERASE.
"Erase TOC ?" appears on the display.
To cancel erasing, press a.
3.
Press w/d (w on the remote control) to start erasing.
"Erasing" flashes on the display, and the level meter shows the
erasing progress.
4.
This unit enters the stop mode when erasing has
been completed.
Note
• The TOC indicator turns off when "TOC Erase" has been
completed.
I Disc Erase
This operation erases all information recorded on a CD-RW disc.
1.
Load the CD-RW disc to be erased.
2.
Press and hold ERASE for approximately 2 seconds.
"Erase Disc ?" appears on the display.
To cancel erasing, press a.
3.
Press w/d (w on the remote control) to start erasing.
"Erasing" flashes on the display, and the level meter shows the
erasing progress.
4.
This unit enters the stop mode when erasing has
been completed.
Cautions
• Never turn off the power of this unit during erasing.
• If "Check Disc" appears on the display during erasing, and
erasing stops, there may be dust or damage on the CD-RW disc.
Check the CD-RW disc and start the erasing operation again.
• Erasing a disc takes approximately 20 minutes.
L
TOC
dB –30 –10 –6 –2 0
CDRW
R
L
dB –30 –10 –6 –2 0
CDRW
R
71
E-