Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gage Bilt GB713SRA
Summary of Contents for Gage Bilt GB713SRA
- Page 1 ORIGINAL INSTRUCTIONS GB713SRA INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court Clinton Twp. MI 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 solutions1@gagebilt.com / www.gagebilt.com MADE in USA...
-
Page 2: Table Of Contents
Description and Technical Specifications ..........................4 Description of Functions ................................5 Warnings ..................................... 6 Principle of Operation ................................7 How to set-up the GB713SRA ..............................8 How to use the GB713SRA ................................ 9 Maintenance and Hydraulic Thread Preparation ........................10 Filling and Bleeding ................................. 11 Troubleshooting .................................. -
Page 3: Warranty
This warranty is void if Seller is not notified in writing of any rejec- tions or defects within 1 year after the receipt of the material by the customer. THIS WARRANTY IS MADE IN LEIU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY. GB713SRA Installation Tool. 1/18 REV 1/23... -
Page 4: Description And Technical Specifications
This tools unique "split" system provides the operator with a lightweight ergonomic tool. The handle and head assembly when held in hand weighs 3.50 lbs. (1.59 kg). The GB713SRA split riveter installation tool operates in conjunction with the GB808 powerunit that requires 90 psi (6.2 bar) to operate. -
Page 5: Description Of Functions
DESCRIPTION OF FUNCTIONS Hanger Head Cylinder Assembly Hydraulic “PULL” Hose Actuator Assembly Lanyard Assembly Air Line/ “RETURN” Air Line (Feed from Regulator to Actuator). GB713SRA Installation Tool. 1/18 REV 1/23... -
Page 6: Warnings
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. GB713SRA Installation Tool. 1/18 REV 1/23... -
Page 7: Principle Of Operation
The spent pintail ejects from the rear of tool. PULL Cycle RETURN Cycle Pressurized Oil Pressurized Air Unpressurized Oil Unpressurized Air Images may not reflect actual tool GB713SRA Installation Tool. 1/18 REV 1/23... -
Page 8: How To Set-Up The Gb713Sra
HOW TO SET-UP THE GB713SRA WARNING: Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 9: How To Use The Gb713Sra
HOW TO USE THE GB713SRA WARNING: Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 10: Maintenance And Hydraulic Thread Preparation
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided. -
Page 11: Filling And Bleeding
Subtract dimension (A) from dimension (B). If stroke is not consistent within 1/64" (.0156) repeat filling and bleeding procedure until stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke. Please contact Gage Bilt for more information. -
Page 12: Troubleshooting
Spent fastener stem may be jammed in pulling head. Disassemble and check for worn or broken parts in nose assembly. Replace defective parts and clean before reassembling. d.) Verify Tool and Nose Assembly are correct for fastener GB713SRA Installation Tool. 1/18 REV 1/23... -
Page 13: Overhaul
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® #630-AA (Gage Bilt part no. 402723) or equivalent during reassembly to prevent tearing or distorting of o'rings. - Page 14 After replacing o’rings on actuator assembly (703532), insert actuator assembly (703532) into manifold- head assembly (704329). (Note direction in picture provided) and push with thumb until it stops. Re-attach the lever and pin to the actuator assembly (703047) on the manifold-head assembly (704329). GB713SRA Installation Tool. 1/18 REV 1/23...
-
Page 15: Parts Lists
PARTS LIST EVACUTATION TUBING —SOLD SEPARATELY SEE CHART PG 17. GB713SRA Installation Tool. 1/18 REV 1/23... -
Page 16: Nose Assembly Selection Chart
PLEASE CONTACT GAGE BILT FOR VACUUM NOSE ASSEMBLY OPTIONS GB713SRA Installation Tool. 1/18 REV 1/23... -
Page 17: Alternative Styles
Alternative Styles (Sold Separately) Pistol Grip (SHA) Inline (SRA) All SRA and SHA tools require a powerunit to operate. Please contact GAGE BILT for more information. Description Pistol Grip Inline Image may not reflect actual tool Pintail Deflector Vacuum SHAV... - Page 18 Hydraulic Powerunits Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) GB808V GB808 POWERUNIT WITH VACUUM POWERUNIT (Sold Separately) (Sold Separately) *GB808 WHEELS OPTIONAL GB808HVB GB808HVB-100 HANGING POWERUNIT WITH VACUUM...
- Page 19 This page intentionally left blank GB713SRA Installation Tool. 1/18 REV 1/23...
-
Page 20: Accessories
Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Contact us for more information. Approved GB713SRA ACCESSORIES Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) Tool Stroke Depth Gage Air Bleeder Assembly Catcher Bag-Stem...