Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gage Bilt GB784
Summary of Contents for Gage Bilt GB784
- Page 1 GB784 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A. e-mail: solutions@gagebilt.com / www.gagebilt.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Description Page Warnings…………………………………………………………………………………………………………..3 Principle of Operation…………………………………………………………………………………………..4 How to use the GB784….……………………………………………………………………………………….5 Description, Operation and Maintenance……………………………………………………………………6 Filling, Bleeding and Troubleshooting……………………………………………………………………….7 Overhaul, Disassembly and Parts Lists……………………………………………………………………8-9 DEXRON® III Oil Safety Data………………………………………..………………………………………...10 Nose Assembly Selection Chart…………………………………...……………………………………..11-12 EU Conformity and Warranty…………………………………………………………………………………13 1.92... -
Page 3: Warnings
73.2 DBA. In this daily basis for damage or wear. Any repair should condition the max level was 81.5 DBA. Therefore, it be done by qualified personnel trained on Gage Bilt is required where prolonged use, hearing procedures. -
Page 4: Principle Of Operation
PRINCIPLE OF OPERATION When the trigger is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve spool causing the air to be redirected. The air is directed to the top of the air piston, moving it in a downward direction. -
Page 5: How To Use The Gb784
HOW TO USE THE GB784 WARNING: OPERATOR MUST READ AND UNDERSTAND ALL WARNINGS AND CAUTIONS. WARNING: IT IS REQUIRED THAT EYE PROTECTION AND HEARING PROTECTION BE WORN DURING OPERATION. WARNING: DO NOT PULL RIVET IN THE AIR. PERSONAL INJURY FROM FASTENER EJECTING MAY OCCUR. -
Page 6: Description, Operation And Maintenance
The GB784 riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximum efficiency. At 90 psi air pressure, the GB784 does not exceed 81.5 db (A) and consumes 3 cfm at 20 cycles a minute. -
Page 7: Filling, Bleeding And Troubleshooting
FILLING AND BLEEDING TOOL WARNING DO NOT CYCLE TOOL WITHOUT AIR BLEEDER, OR THE SCREW AND STAT-O-SEAL, INSTALLED IN TOOL HEAD. SEVERE PERSONAL INJURY MAY RESULT. CAUTION BEFORE FILLING HANDLE, AIR PISTON SHOULD BE ALL THE WAY DOWN. CAUTION WHEN FORCING PISTON ROD ASSEMBLY DOWNWARD WITH HEAD CYLINDER ASSEMBLY REMOVED, HYDRAULIC FLUID WILL EJECT FORCIBLY FROM HANDLE. -
Page 8: Overhaul, Disassembly And Parts Lists
OVERHAUL The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and drawings. Use extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing seals, always apply a good lubricant, such as Lubriplate®, to the surfaces. It is recommended that tool kit (GB784TK) be used to facilitate overhaul. -
Page 9: Air Valve
HANDLE To inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the head cylinder (784221) first. For complete disassembly, start by removing base cover (744124). Next, holding tool upright, remove four button-head cap screws (402479). Lift head cylinder (784221) from handle (744129) and set aside o'ring (S832) and gasket (704129). Empty all hydraulic fluid into a container. -
Page 10: Dexron® Iii Oil Safety Data
DEXRON® III OIL SAFETY DATA FIRST AID MEASURES Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material from skin, use soap and water. -
Page 11: Nose Assembly Selection Chart
Nose assemblies are not furnished with the tool and must be purchased separately. In ordering heads be sure to specify the shank diameter and head style (universal or countersunk) of the rivets to be in- stalled. The following pulling heads will fit directly on the GB784 Riveter. (NOTE: Cherry 681 series pulling ®... - Page 12 SETTING THE SHIFT POINT: The shift point must be adjusted to ensure the flushness of the rivet stem after installation. To Adjust: 1. Connect the tool to a clean dry air source of 90 psi to 100 psi. Remove nut. 2.
-
Page 13: Eu Conformity And Warranty
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB784 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.