Gage Bilt GB751 Installation Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Power Tool
  5. GB751
  6. Installation manual

Gage Bilt GB751 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S/N: 1324 AND ABOVE
GB751
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading

Related Manuals for Gage Bilt GB751

Summary of Contents for Gage Bilt GB751

  • Page 1 S/N: 1324 AND ABOVE GB751 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    - .780" (19.8 mm) Rated pull load - 2,200 lbs. (9.8 kN) Noise level - 81.5 dB (A) Vibration - Tested– No Hazards Found S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    It is recommended operator wear a suitable gloves WARNING during operation where prolonged use is expected. Air pressure not to exceed 100 psi (6.9 bar). S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 4: Principle Of Operation

    CYLINDER HEAD HEAD PISTON PRESSURE PRESSURE PRESSURE PISTON PISTON PRESSURE PRESSURE VALVE SPOOL PISTON PRESSURE PRESSURE PRESSURE EXHAUST Image may not reflect actual tool S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: How To Use The Gb751

    Always disconnect air supply when tool is not in use to prevent accidental start-up. NOSE HEAD ASSEMBLY CYLINDER ASSY DEFLECTOR RIVET WORK ACTUATOR SHIPPING ASSY PLUG QUICK DISCONNECT FITTING Image may not reflect actual tool. S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Description And Maintenance

    2200 lbs. (9.8 kN) with 90 psi. (6.2 bar) air pressure at the air inlet. The GB751 riveter operates on a wide range of air pressure, with 90 to 100 psi. (6.2-6.9 bar) providing the maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB751 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles a minute.

  • Page 7: Filling, Bleeding And Troubleshooting

    Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Overhaul

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in Front of tool or rear of tool when installing fastener.

  • Page 9: Disassembly And Parts Lists

    The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply Loctite® #242 and torque the button head cap screws (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 10: Air Valve

    NOTE: Valve spring tool (704162) will facilitate the proper installation of the spring (704141). Valve sleeve (704140) can be pulled out using valve sleeve removal tool (704163). S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 11: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations S/N: 1324 AND ABOVE 6/11 REV 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Nose Assembly Selection Chart

    UNIM ATIC®, ASP® IS A REGISTERED TRADEM ARK OF ALCOA INC. CHERRYM AX® AND M BC® ARE REGISTERED TRADEM ARKS OF CHERRY AEROSPACE. FASTACK® AND SUPERTACK® ARE REGISTERED TRADEM ARKS OF ALLFAST FASTENING SYSTEM S INC. GAGE BILT CERTIFIES THE GB751 WILL INSTALL THE ABOVE FASTENERS PLEASE NOTE: Due to lever assembly 1) RIGHT ANGLE NOSE ASSEMBLIES MAY REQUIRE MORE THAN ONE PULL.

  • Page 13: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB751 FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.

Table of Contents