Gage Bilt GB713 Original Instructions Manual
Hide thumbs
Also See for GB713:
- Installation manual (14 pages) ,
- Original instructions manual (20 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Advertisement
Table of Contents
Related Manuals for Gage Bilt GB713
Summary of Contents for Gage Bilt GB713
- Page 1 ORIGINAL INSTRUCTIONS GB713 INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
-
Page 2: Table Of Contents
Description and Technical Specifications ..........................3 Description of Functions ................................4 Warnings ..................................... 5 Principle of Operation ................................6 How to set-up the GB713 ................................7 How to use the GB713 ................................8 Maintenance ....................................9 Filling and Bleeding ................................. 10 Troubleshooting .................................. -
Page 3: Description And Technical Specifications
4,500 lbs. (20.0 kN) with 90 psi (6.2 bar) air pressure at the air inlet. The GB713 riveter operates on 90 to 100 psi (6.2-6.9 bar) of air pressure, providing the maximum efficiency. At 90 psi (6.2 bar) air pressure, the GB713 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles a minute. -
Page 4: Description Of Functions
DESCRIPTION OF FUNCTIONS Head Cylinder Assy Pintail Deflector Actuator Air Inlet Handle Assy GB713 7/11 REV 6/16... -
Page 5: Warnings
6. Check that the means of protection from ejection of fastener and/or stem is in place and operative (such as the deflector). 7. Forcible ejection of the mandrel from the front of the nose assembly is possible. GB713 7/11 REV 6/16... -
Page 6: Principle Of Operation
Piston Rod Assy moves up Piston Rod Assy moves down Air Piston moves up Air Piston moves down Air exhaust Air exhaust Pressurized Oil Pressurized Air Return Oil Exhaust Air Image may not reflect actual tool GB713 7/11 REV 6/16... -
Page 7: How To Set-Up The Gb713
HOW TO SET-UP THE GB713 WARNING: Only qualified and trained operators should install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 8: How To Use The Gb713
HOW TO USE THE GB713 WARNING: Only qualified and trained operators should install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 9: Maintenance
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants should be avoided. -
Page 10: Filling And Bleeding
(B). If stroke doesn’t check .760" (19.3 mm) min. (See figures below) repeat steps 4 thru 6. Bleeder hole on head cylinder (713121) Button head cap screw (402482) & stat-o- seal (S572) Air Bleeder Assy (704153) Image may not reflect actual tool. GB713 7/11 REV 6/16... -
Page 11: Troubleshooting
TOOL, remove the nose from the tool and disassemble. Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. GB713 7/11 REV 6/16... -
Page 12: Overhaul
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings. - Page 13 Apply Teflon® tape onto threads of air actuator assy (704130) one to two wraps. Thread the air actuator assy (704130) all the way into handle assy (744129) with fingers. Insert and turn 5/8” (15.9 mm) wrench and snug tight approximately 1/4-1/2 turn. GB713 7/11 REV 6/16...
- Page 14 If ports are plugged, use needle nose pliers to grasp end of spring (744144), turning clockwise and pulling to dislodge from groove in casting. Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144). Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152). GB713 7/11 REV 6/16...
-
Page 15: Parts Lists
PARTS LIST GB713 7/11 REV 6/16... -
Page 16: Dexron® Iii Oil Safety Data
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. GB713 7/11 REV 6/16... -
Page 17: Nose Assembly Selection Chart
T RIVET®, CHERRYM A X® A ND M B C® A RE REGISTERED TRA DEM A RKS OF CHERRY A EROSP A CE. M ONOB OLT® A ND TLR® A RE REGISTERED TRA DEM A RKS OF A VDEL UK LIM ITED. A SP ® IS A REGISTERED TRA DEM A RK OF A LCOA INC. GAGE BILT CERTIFIES THE GB713 WILL INSTALL THE ABOVE FASTENERS PLEASE NOTE: Due to *ALL OFFSET 204 SERIES NOSES REQUIRE 751204 ADAPTER &... -
Page 18: Eu Conformity And Warranty
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB713 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.