Page 1
GB743 S/N: 2269 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.
It is recommended operator wear a suitable glove WARNING during operation where prolonged use is expected. Air pressure not to exceed 100 psi (6.9 bar). S/N: 2269 AND ABOVE REV. 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Always disconnect air supply when tool is not in use to prevent accidental start-up. NOSE HEAD ASSEMBLY CYLINDER ASSY DEFLECTOR RIVET WORK ACTUATOR SHIPPING ASSY PLUG QUICK DISCONNECT FITTING Image may not reflect actual tool S/N: 2269 AND ABOVE REV. 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
4000 lbs. (17.8 kN) with 90 psi (6.2 bar) air pressure at the air inlet. The GB743 riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency. At 90 psi.
Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. S/N: 2269 AND ABOVE REV. 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in Front of tool or rear of tool when installing fastener.
743407 - PISTON S834 - O'RING 401089 - BACK-UP RING S834 - O'RING S572 - STAT-O-SEAL 743108 402482 HEAD CYLINDER ASSY BUTTON HEAD CAP SCREW S/N: 2269 AND ABOVE REV. 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
744142 - VALVE PLUG 744124 - BASE COVER 400785 - O'RING 744136 PISTON ROD ASSY 744143 - MUFFLER (INCLUDES S908 AND A-201) 744149 - PIN S/N: 2269 AND ABOVE REV. 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations S/N: 2269 AND ABOVE REV. 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES REV. 10/14 S/N: 2269 AND ABOVE REV. 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB743 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.