Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gage Bilt GB743SHAVT/6NF
Summary of Contents for Gage Bilt GB743SHAVT/6NF
- Page 1 ORIGINAL INSTRUCTIONS GB743SHAVT/6NF INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions1@gagebilt.com / www.gagebilt.com...
-
Page 2: Table Of Contents
Description and Technical Specifications ..........................4 Description of Functions ................................5 Warnings ..................................... 6 Principle of Operation ................................7 How to set-up the GB743SHAVT/6NF ............................8 How to use the GB743SHAVT/6NF ............................9 Maintenance and Hydraulic Thread Preparation ........................10 Filling and Bleeding ................................. 11 Troubleshooting .................................. -
Page 3: Eu Conformity / Warranty
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct., Clinton Twp., Michigan U.S.A. +1(586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 The Supply of Machinery (Safety) Regulations 2008 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. -
Page 4: Description And Technical Specifications
Any other use is forbidden. The GB743SHAVT/6NF is a pneumatic-hydraulic split handle installation tool designed specifically for the efficient installation of blind rivets. This tools unique "split" system provides the operator with a lightweight ergonomic tool. The handle and head assembly when held in hand weighs 3.5 lbs. -
Page 5: Description Of Functions
DESCRIPTION OF FUNCTIONS Hanger Head Cylinder Assembly Nose Assembly Lever Handle Assembly Hydraulic “PULL” Air Lines Lanyard Assembly Image may not reflect actual tool. GB743SHAVT/6NF 10/22 REV 3/23... -
Page 6: Warnings
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip can then be used to support the tool. GB743SHAVT/6NF 10/22 REV 3/23... -
Page 7: Principle Of Operation
Further force breaks the pintail off. When the actuator is released the piston returns forward. The spent pintail is evacuated out the back of the nose assembly by the vacuum system. PULL Cycle RETURN Cycle Pressurized Air Unpressurized Air Pressurized Oil Unpressurized Oil Images may not reflect actual tool GB743SHAVT/6NF 10/22 REV 3/23... -
Page 8: How To Set-Up The Gb743Shavt/6Nf
TOOL INTO FITTING A-204 RED SHIPPING PLUG AIR LINE FROM TOOL USER QUICK DISCONNECT FITTING 1/2” (12.7 mm) AIR OUTLET AIR HOSE AIR INLET HYDRAULIC LINE FROM TOOL HYDRAULIC OUTLET GB808V Powerunit (Image may not reflect actual tool) GB743SHAVT/6NF 10/22 REV 3/23... -
Page 9: How To Use The Gb743Shavt/6Nf
HOW TO USE THE GB743SHAVT/6NF WARNING: Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded mechanical fasteners. WARNING: Operator MUST read and understand all warnings and cautions. WARNING: t is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment. -
Page 10: Maintenance And Hydraulic Thread Preparation
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided. -
Page 11: Filling And Bleeding
Subtract dimension (B) from dimension (A). If stroke is not consistent within 1/64" (.396 mm) repeat steps 1 - 9 until stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke. -
Page 12: Troubleshooting
Verify Tool and Nose Assembly are correct for fastener. d.) Spent fastener stem may be jammed in pulling head. Disassemble and check for worn or broken parts in nose assembly. Replace defective parts, clean and re-lube jaws before reassembling. GB743SHAVT/6NF 10/22 REV 3/23... -
Page 13: Overhaul
9. Reassembly sequence is opposite of disassembly. Be sure relative positions of o'rings and back-up rings are as shown in exploded view and part list. Coat hose fitting threads with a non-hardening Teflon® thread compound such as Slic-tite® (Gage Bilt part no. 403237). DO NOT USE TEFLON® TAPE. - Page 14 Poppet valve assembly sits flush against pin dia. in hole Reinsert pin into hole on handle assembly (700343). Re-attach the lever and tighten set screw. Note: View above shows proper orientation of lever. GB743SHAVT/6NF 10/22 REV 3/23...
-
Page 15: Parts Lists
PARTS LIST GB743SHAVT/6NF 10/22 REV 3/23... -
Page 16: Hydraulic Powerunits / Accessories
Hydraulic Powerunits Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) GB808 GB808V GB808HVB-100 POWERUNIT POWERUNIT WITH VACUUM HANGING POWERUNIT WITH VACUUM (Sold Separately) (Sold Separately) & PINTAIL SENSOR... - Page 17 8N-743-24 and spare nose tip (10204) to convert to 6N-743-24. All other nose tips must be ordered separately. When ordering tool fastener specific, contact Gage Bilt for more information. “VT“ installation tools are not furnished with the nose assemblies above and must be ordered for your specific fastener.
-
Page 18: Alternative Styles
Pull load - 4,000 lbs. (17.79 kN) Standard Hyd. Hose Length - 3ft (1.5m) 5t Hyd. Hoses are recommended with use of Backpack Additional custom lengths are available. 5t Hyd. Hoses are recommended with use of Backpack Additional custom lengths are available. GB743SHAVT/6NF 10/22 REV 3/23... - Page 19 This page intentionally left blank GB743SHAVT/6NF 10/22 REV 3/23...
-
Page 20: Accessories
Riveter Kits Available (Sold Separately) Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Contact us for more information. Approved Split Handle Installation Tool Backpacks For 5ft hose Split System Tools. (Sold Separately) TEFLON® IS A REGISTERED TRADEMARK OF E.I. DUPONT DE NEMOURS & CO. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. SLIC-TITE® IS A REGISTERED TRADEMARK LA-CO INDUSTRIES INC.