Table of Contents
Advertisement
Quick Links
GAGE BILT
MADE IN U.S.A.
GB715 S/N: 1242 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
GB715
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
44766 Centre Court
Clinton Twp. MI 48038
e-mail: solutions@gagebilt.com / www.gagebilt.com
1
S/N: 1242 AND ABOVE
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
(586) 226-1500
(586) 226-1505 Fax
REV. 2/16
Advertisement
Table of Contents
Related Manuals for Gage Bilt GB715
Summary of Contents for Gage Bilt GB715
- Page 1 GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A. e-mail: solutions@gagebilt.com / www.gagebilt.com GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16...
-
Page 2: Table Of Contents
Disassembly and Parts Lists.............................. 13-14 DEXRON® III Oil Safety Data ..............................15 Nose Assembly Selection Chart ............................. 16 EU Conformity and Warranty ..............................17 GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 3: Description And Technical Specifications
1400 lbs. (6.2 kN) with 90 psi (6.2 bar) air pressure at the air inlet. The GB715 riveter operates on 90 to 100 psi (6.2-6.9 bar) Max. providing the maximum efficiency. At 90 psi (6.2 bar) air pressure, the GB715 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles a minute. -
Page 4: Description Of Functions
DESCRIPTION OF FUNCTIONS Head Cylinder Actuator Handle Air Inlet GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 5: Safety Warnings
(such as the deflector). can then be used to support the tool. 7. Forcible ejection of the mandrel from the front of the nose assembly is possible. GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 6: Principle Of Operation
PULL Cycle Air exhaust Air exhaust RETURN Cycle Pressurized Oil Exhaust Air Return Oil Exhaust Air Pressurized Air Image may not reflect actual tool GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 7: How To Setup The Gb715
NOSE ASSY HEAD CYLINDER RIVET WORK ACTUATOR RED SHIPPING PLUG USER QUICK DISCONNECT FITING AIR HOSE AIR INLET Image may not reflect actual tool GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 8: How To Use The Gb715
3. Press actuator to start cycle. Continue to press until fastener breaks. 4. Release actuator as soon as fastener breaks. 5. Repeat steps 1-5. Images may not reflect actual tool or fastener GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 9: Maintenance
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants should be avoided. -
Page 10: Filling And Bleeding
1/64" (.0156) repeat bleeding steps 4-7. Bleeder hole on head cylinder (715110) Button head cap screw (402482) & stat-o-seal (S572) Air Bleeder Assy (704153) Image may not reflect actual GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 11: Troubleshooting
Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 12: Overhaul
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings. -
Page 13: Disassembly And Parts Lists
(715107) surface. The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply Loctite® #242 (Gage Bilt #A-1006) and torque the button head cap screws (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). -
Page 14: Parts List
PARTS LIST GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 15: Dexron® Iii Oil Safety Data
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations GB715 S/N: 1242 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. REV. 2/16... -
Page 16: Nose Assembly Selection Chart
CHERRYM AX® AND M BC® ARE REGISTERED TRADEM ARKS OF CHERRY AEROSPACE FASTENERS. FASTACK® AND SUPERTACK® ARE REGISTERED TRADEM ARKS OF ALLFAST FASTENING SYSTEM S IN GAGE BILT CERTIFIES THE GB715 WILL INSTALL THE ABOVE FASTENERS **ALL COUNTERSUNK 'C' NOSE ASSEMBLIES MAY USED TO INSTALL BOTH UNIVERSAL AND COUNTERSUNK HEAD RIVETS. -
Page 17: Eu Conformity And Warranty
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB715 FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.