Table of Contents
Advertisement
Internal I/O Connectors
X
Front Panel
CPU_FAN
1
VGA
HDMI
+12V Power
LGA 1700
DP++
DP++
2.5G LAN 1
USB3_1/2
USB2_1/2
2.5G LAN 2
USB3_3/4
USB2_3/4
10G LAN 1
10G LAN 2
USB 3 10/9/8/7
M.2 M Key
Mic-in
M2CN4
Line-out
Line-in (opt.)
1
JP31
PCIE1 (PCIe x16)
Intel
PCIE2 (PCIe x4)
Front LAN
LED
R680E/Q670E
1
2
SPI
1
2
SMBus
PCIE3 (PCIe x4)
5
7
8
USB3_5/6
USB2_5/6
2
TSJP3
TSJP8
TSJP6
1
10
Front Audio
2
6
2
6
2
6
2
6
2
6
2
6
PCIE4 (PCIe x4)
1
9
1
5
1
5
1
5
1
5
1
5
1
5
20
11
TSJP4
TSJP2
TSJP7
5
6
6
5
TSJP1
TSJP5
1
JP29/30/28
1
2
1
2
1
2
2
1
8
1
1
1
9
1
9
1
1
10
2
10
2
1
1
1
S/PDIF
DIO
DIO
SYS_FAN1 COM1
COM2 USB2_13
Power
SATA0(R4)/SATA1(R5)/SATA2(R6)/SATA3(R7)
USB2_11/12
„ Front Panel Pin Assignment
Pin
Assignment
1
N.C.
3
3V3
HD-LED
5
HD_LED
7
Ground
RESET
9
SYS_RST-
11
N.C.
HDD LED - Hard Disk Drive LED
Lighting of the LED indicates that the hard drive is being accessed.
RESET - Reset Switch
This switch allows you to reboot without having to power off the system.
Power/Standby LED
When the system's power is on, this LED will light up. When the system is in the S1 (POS -
Power On Suspend) state, it will blink at 1-second intervals. When the system is in the S3 (STR
- Suspend To RAM) state, it will blink at 4-second intervals.
Power Button
This button is used to switch the system's power on or off .
User's Manual | ADS310-R680E/Q670E
SYS_FAN3
1
Battery
2
1
PWR-LED
ATX Power
HD-LED
1
2
Front Panel
11
ATX-SW
RESET
InnoAGE HDR1
1
2
5
6
1
SYS_FAN2
13
J36
12
eSPI
JP25
JP5
1
1
2
1
JP26
1
1
SOJ1
1
9
PS/2
JP33
1
2
1
1
JP32
M.2 M Key
M2CN3
CN1
M.2 E Key
1
M2CN2
1
1
1
Pin
Assignment
2
V_SUS_LED
PWR-LED
4
V_SUS_LED
6
SUS_LED
8
Ground
ATX-SW
10
PWR_BTN-
12
---
Internal I/O Connectors
X
S/PDIF Connector
VGA
HDMI
+12V Power
DP++
DP++
2.5G LAN 1
USB3_1/2
USB2_1/2
2.5G LAN 2
USB3_3/4
USB2_3/4
10G LAN 1
10G LAN 2
USB 3 10/9/8/7
Mic-in
Line-out
Line-in (opt.)
PCIE1 (PCIe x16)
SPDIF out
PCIE2 (PCIe x4)
Front LAN
LED
1
2
1
2
SMBus
PCIE3 (PCIe x4)
5
7
8
GND
2
Front Audio
PCIE4 (PCIe x4)
1
9
SPDIF in
+5V
JP29/30/28
1
8
1
1
1
1
S/PDIF
DIO
DIO
5
Power
1
The S/PDIF connector is used to connect an external S/PDIF port. Your S/PDIF port may be
mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear of
the system chassis then connect the audio cable to the S/PDIF connector. Make sure pin 1 of
the audio cable is aligned with pin 1 of the S/PDIF connector.
Chapter 2
HARDWARE INSTALLATION
CPU_FAN
1
SYS_FAN3
1
Battery
LGA 1700
ATX Power
1
2
Front Panel
11
InnoAGE HDR1
1
2
M.2 M Key
5
6
M2CN4
1
SYS_FAN2
1
JP31
13
J36
eSPI
Intel
JP25
JP5
1
1
2
1
JP26
1
1
SOJ1
1
R680E/Q670E
SPI
9
PS/2
JP33
1
2
1
USB3_5/6
JP32
USB2_5/6
1
TSJP3
TSJP8
TSJP6
1
10
M.2 M Key
M2CN3
CN1
2
6
2
6
2
6
2
6
2
6
2
6
M.2 E Key
1
5
1
5
1
5
1
5
1
5
1
5
20
11
1
TSJP4
TSJP2
TSJP7
M2CN2
6
5
6
5
TSJP1
TSJP5
1
1
2
1
2
1
2
2
1
1
9
1
9
1
1
1
1
10
2
10
2
1
SYS_FAN1 COM1
COM2 USB2_13
SATA0(R4)/SATA1(R5)/SATA2(R6)/SATA3(R7)
USB2_11/12
26
Advertisement
Table of Contents
