Page 2
1. The changes or modifications not expressly approved by the party responsible for com- are the properties of the respective owners. pliance could void the user’s authority to operate the equipment. 2. Shielded interface cables must be used in order to comply with the emission limits. User's Manual | ADS630-R680E/Q670E...
Battery ..........................32 Chapter 3 - BIOS Settings ......................33 Overview ..........................33 Main ............................34 Advanced ..........................34 CPU Configuration ......................35 Power & Performance ....................35 PCH-FW Configuration ....................36 Trusted Computing ......................37 NCT6126D Super IO Configuration ................38 NCT6126D HW Monitor ....................39 User's Manual | ADS630-R680E/Q670E...
Page 4
• To reduce the risk of electric shock, unplug the power cord before removing the sys- tem chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord. User's Manual | ADS630-R680E/Q670E...
1 x VGA 2 x DP++ 1 x HDMI 2.0a Audio 1 x Line-out 1 x Mic-in User's Manual | ADS630-R680E/Q670E 1 x Line-in (opt. by request, MOQ required) INTERNAL I/O Serial 2 x RS-232/422/485 (RS-232 w/ power) (2.54mm pitch)
Page 7
SECURITY Nuvoton TPM2.0 (opt., MOQ required) POWER Type Connector 8-pin ATX 12V power 24-pin ATX power Consumption RTC Battery CR2032 Coin Cell OS SUPPORT Microsoft Windows 10 IoT Enterprise 64-bit Windows Server 2022 Linux Linux www.dfi.com User's Manual | ADS630-R680E/Q670E...
Plug and Play peripherals. RTC Timer The Real Time Clock (RTC) installed on the system board allows your system to automatically power-on on the set date and time. User's Manual | ADS630-R680E/Q670E...
TCA6408A Audio Jack ALC888 (Line-out/Mic-in/Line-in (opt.)) SMBus Super IO RS232/422/485 2x SPI BIOS with WDT RS232 4x eSPI TPM 2.0 Fan Control NPCT754 Case Open PS/2 KB/MS H/W Monitor eSPI 80 port Header MECHANICAL DRAWING 304.80 User's Manual | ADS630-R680E/Q670E...
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides better system performance because it doubles the data transfer rate. Features • Four 288-pin UDIMM up to 128GB • Dual Channel DDR4 3200MHz (ECC support: R680E only) User's Manual | ADS630-R680E/Q670E...
Hold the card by its edges and remove it from the slot. The tabs snap automatically to the edges of the card and lock the card in place. Step 1 Step 1 Step 2 Step 2 Step 3 Step 3 User's Manual | ADS630-R680E/Q670E...
Align the 4 screw holes and tighten the heat sink up by inserting screws, DO remember to con- nect the fan cable on the board. (The location of fan connector may vary.) There are 4 screw holes around the CPU for the heat sink to be mounted. User's Manual | ADS630-R680E/Q670E...
2. Put a jumper cap on pin 2 and pin 3. Wait for a few seconds and set it back to its de- fault setting, i.e. jumper cap on pin 1 and pin 2. 3. Plug the power cord and power-on the system. 1-2 On: Normal (default) 2-3 On: Clear CMOS Data User's Manual | ADS630-R680E/Q670E...
JP28 is used to set DIO Power Voltage. JP29/30 are used to set DIO Power. JP28 1-2 On: 5VDU (default) 2-3 On: 5V 1-2 On: AT mode (default) 2-3 On: ATX Mode JP29/30 1-2 On: 5V_DIO (default) 2-3 On: GND User's Manual | ADS630-R680E/Q670E...
M.2 M Key M2CN2 PCI 1 JP33 PCI 2 M2CN3 M.2 E Key JP25 is used to select PS/2 and USB Wake up. 1-2 On: 2-3 On: Control by BIOS (default) Wake up disable User's Manual | ADS630-R680E/Q670E...
JP31, JP32 and JP33 are used to control the power of M2CN4, M2CN2 and M2CN3. TSJP1 and TSJP5 are used to determine the power of COM1/COM2. 1-2 On: 2-3 On: 3V3(default) 3V3DU 1-3, 2-4 On: 3-5, 4-6 On: RS232 Standard (default) RS232 with Power User's Manual | ADS630-R680E/Q670E...
3-5, 4-6 On: RS232 (default) RS422 RS485 TSJP4,3,2 and TSJP8,7,6 are used to determine the signal type of COM1/COM2. TSJP2(COM1), TSJP6(COM2) 1-3, 4-6 On: 3-5, 4-6 On: 3-5, 2-4 On: RS232 (default) RS422 RS485 User's Manual | ADS630-R680E/Q670E...
• RJ45 LAN 1/2 • 1 HDMI port • 1 VGA port • 10G LAN 3/4 • 4 USB 3.2 Gen 1 ports • 1 Line-in jack (optional) • 1 Line-out jack • 1 Mic-in jack User's Manual | ADS630-R680E/Q670E...
The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable connector to the VGA port. After you plug the monitor’s cable connector into the VGA port, gen- tly tighten the cable screws to hold the connector in place. User's Manual | ADS630-R680E/Q670E...
Mic-in Jack (Pink) This jack is used to connect an external microphone. Front Audio The front audio connector allows you to connect to the second line-out and mic-in jacks that are at the front panel of your system. User's Manual | ADS630-R680E/Q670E...
• 4 Serial ATA 3.0 ports with data transfer rate up to 6Gb/s D_IOA3 • Integrated Advanced Host Controller Interface (AHCI) controller D_IOA4 • Support RAID 0, RAID 1, RAID 5, RAID 10 D_IOA5 D_IOA6 D_IOA7 User's Manual | ADS630-R680E/Q670E...
Insufficient power supplied to the system may result in instability or malfunction of the add-in boards and peripherals. Calculating the system’s approximate power Control usage is important to ensure that the power supply meets the system’s consump- tion requirements. User's Manual | ADS630-R680E/Q670E...
Power On Suspend) state, it will blink at 1-second intervals. When the system is in the S3 (STR - Suspend To RAM) state, it will blink at 4-second intervals. Power Button This button is used to switch the system's power on or off . User's Manual | ADS630-R680E/Q670E...
Install PCI cards for other expansion demands. M.2 Socket The M.2 socket is the Next Generation Form Factor (NGFF) which is designed to support mul- tiple modules and make the M.2 more suitable in application for solid-state storage. User's Manual | ADS630-R680E/Q670E...
• There exists explosion hazard if the battery is incorrectly installed. the board when it’s correctly mounted. • Replace only with the same or equivalent type recommended by the manufacturer. • Dispose of used batteries according to local ordinances. User's Manual | ADS630-R680E/Q670E...
“Press DEL to run setup” will appear on the screen. If the message disappears before you respond, restart the system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously. User's Manual | ADS630-R680E/Q670E...
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min- utes from 00 to 59. Second displays seconds from 00 to 59. User's Manual | ADS630-R680E/Q670E...
Enable or disable CPU Power Management. It allows CPU to enter "C states" when it’s idle and nothing is executing. Note: Some of the fields may not be available when the features are not supported by the equipped CPU. User's Manual | ADS630-R680E/Q670E...
When disabled, AMT BIOS features are no longer supported and user is no longer able to ac- cess MEBx Setup. This option does not disable manageability features in FW. ME Unconfig on RTC Clear When disabled, ME will not be unconfigured on RTC Clear. Firmware Update Configuration ► Configurate firmware update. User's Manual | ADS630-R680E/Q670E...
ESC: Exit Version 2.22.1284. Copyright (C) 2022 AMI Security Device Support This field is used to enable or disable BIOS support for the security device such as an TPM 2.0 to achieve hardware-level security via cryptographic keys. User's Manual | ADS630-R680E/Q670E...
The sub-menus are detailed in following sections. Enable or disable the current serial COM port. RS485 Auto Flow Enable or disable RS485 auto flow. This field is only available for COM ports that support RS485 mode. User's Manual | ADS630-R680E/Q670E...
▼ SYS Smart Fan/CPU Smart Fan Control = [Disabled] Fix Fan Speed Count Set the fan speed, the value ranging from 1-100%, 100% being full speed. The fans will al- ways operate at the specified speed regardless of gauged temperatures. User's Manual | ADS630-R680E/Q670E...
Select flow control type: None or Hardware RTS/CTS. Flow Control is for RS485 mode and is only supported by Serial Port 1 (COM1). VT-UTF8 Combo Key Support Enable or disable VT-UTF8 Combination Key Support for ANSI/VT100 terminals. User's Manual | ADS630-R680E/Q670E...
The system automatically powers on after power failure. S5 State The system enter soft-off state after power failure. Power-on signal input is required to power up the system. Last State The system returns to the last state right before power failure. User's Manual | ADS630-R680E/Q670E...
Maximum time the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value: for a Root port it is 100 ms, for a Hub port the delat is taken from Hub descriptor. User's Manual | ADS630-R680E/Q670E...
Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value. Media detect count Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. User's Manual | ADS630-R680E/Q670E...
Enables power on of the system via LAN. Note that configuring Wake on LAN in the opera- tion system does not change the value of this setting, but does override the behavior of Wake on LAN is OS controlled power states. Blink LEDs Blink LEDs for a duration up to 15 seconds. User's Manual | ADS630-R680E/Q670E...
Version 2.22.1284. Copyright (C) 2022 AMI Please select a submenu and press Enter. The submenus are detailed in the following pages. VMD setup menu ► VMD Configuration settings. PCI Express Configuration ► PCI Express Configuration settings. VT-d Disable or enable VT-d. User's Manual | ADS630-R680E/Q670E...
Page 46
Intel Rapid Recovery Technology Enable or disable Intel Rapid Recovery Technology. RRT volumes can span internal and eSATA drives Enable or disable RRT volumes can span internal and eSATA drives. Intel(R) Optane(TM) Memory Enable or disable Intel(R) Optane(TM) Memory. User's Manual | ADS630-R680E/Q670E...
Enable or disable this field to detect non-compliance PCIe devices in the PEG. This field may not appear when the port does not support Non-compliant device detection. SATA Configuration ► See next page. HD Audio Configuration ► Enable or disable HD Audio. User's Manual | ADS630-R680E/Q670E...
Secure Boot. Press Enter and a prompt will show up for you to confirm. Reset To Setup Mode Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm. User's Manual | ADS630-R680E/Q670E...
Select this option to save BIOS configuration settings to a USB flash device. ► Restore Setting from file This field will appear only when a USB flash device is detected. Select this field to restore set- ting from the USB flash device. User's Manual | ADS630-R680E/Q670E...
When the BIOS IC needs to be replaced, you have to populate it properly onto the system board after the EEPROM programmer has been burned and follow the technical person's instructions to confirm that the MAC address should be burned or not. User's Manual | ADS630-R680E/Q670E...