Spray Gun; Important Specifications; Main Specifications - Anest Iwata WIDER4L Series Instruction Manual

INSTRUCTION MANUAL

Spray Gun

Be sure to observe warning s and cauti o ns i n this instructi o n manual.
If not, it can cause paint ejecti o n and serious bodily i n j u ry by drawi n g organic solvent.
Be sure to observe fol l owing marked items which are especially important .
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury
or property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are
the minimum necessary conditions. Follow national and local regulations regarding fire prevention,
electricity and safety as well as your own company regulations.
IMPORTANT WARNING: Our spray guns, airbrushes, and other products are made to conform by our local group companies with local laws and regulations
that may differ from place to place. Improper trade of products outside of designated domestic territories (unauthorized reselling) can result in legal violations,
local fines, and penalties. ANEST IWATA CORPORATION assumes no liability for products acquired through unauthorized reselling and in such cases and due
to quality control protocols, unauthorized reselling renders the warranty null and void.

Important specifications

0.70MPa / 7.0bar / 100psi
Max. Pressure
0.11MPa / 1.1bar / 16psi
WIDER4L _HVLP max. pressure
84 dB(A)
Noise l e vel
Spray condition Recommended
1m backwards from spray gun, 1.6m height
Measuri n g point
Atmosphere: 5°C ~40°C (41°F~104°F)
Max. temperature
Air G1/4(NPS1/4) / FluidG1/4(NPS1/4)
Air & fl u i d Connecti o n
355g / 0.78l b s.
Mass
Important
Never connect pressure feedi n g pai n t except pressure feed type spray gun.

Main specifications

Type
Model of
feed
WIDER4 -12J2
-13J2
-13J2
-13J2
Gravity
-18N2
-25W1
WIDER4L -V13J2
-V13J2
-V16J2
*1. Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
/
Air and Fl u id: 5°C ~43°C (41°F~109°F)
Nozzle
Air cap assy
Mark
Orifice
Mark
Φ mm (in)
1.2 (0.047) 12
1.3 (0.051) 13
WIDER4-J2
1.4 (0.055) 14
1.6 (0.063) 16
1.8 (0.071) 18 WIDER4-N2
2.5 (0.098) 25 WIDER2-W1
V4-13
1.3 (0.051)
V4-14
1.4 (0.055) WIDER4L-J2
V4-16
1.6 (0.063)
Model
WIDER4
WIDER4L
Recommended condition
*1 Atomizing air Air pressure
pressure inside air cap
MPa (bar / PSI) MPa (bar/PSI)
0.2 (2.0 / 29)
0.29 (3.0/ 43)
0.2 (2.0 / 29)
0.29 (3.0/ 43)
0.2 (2.0 / 29)
0.29 (3.0/ 43)
-
0.2 (2.0 / 29)
0.29 (3.0/ 43)
0.2 (2.0 / 29)
0.29 (3.0/ 43)
0.29 (3.0/ 43)
0.11 (1.1 / 16) 0.07
1
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction
manual, before use and retain for reference.
Fluid nozzl e – Fl u id needle assy combi n ation
Flui d nozzl e
Orifice Φ mm (in) Mark
Φ 1.2 (0.047) / W2 / 12
Φ 1.3 (0.051) / W4 / 13
Φ 1.4 (0.055) / W4 / 14
Φ 1.6 (0.063) / W4 / 16
Φ 1.8 (0.071) / W2 / 18
Φ 2.5(0.098) / W2 / 25
Φ 1.3 (0.051) / W4L / V4-13
Φ 1.4 (0.055) / W4L / V4-14
Φ 1.6 (0.063) / W4L / V4-16
Air Pattern
Fluid output
consumption
l/min (cfm) mm (in)
ml/min
140 280 (9.8) 175 (6.9)
160 370 (13.1) 250 ( 9.8)
160 280 ( 9.9) 225 (8.8)
200 370 (13.1) 300 (11.8)
210 280 ( 9.9) 225 (10.0)
265 370 (13.1) 320 (12.6)
240 280 ( 9.9) 270 (10.6)
310 370 (13.1) 340 (13.4)
320 290 (10.2) 260 (10.2)
400 380 (13.4) 320 (12.6)
555 360 (12.7) 380 (14.9)
110 280 (11.0)
130 270 (9.5) 290 (11.4)
150 300 (11.8)
Fluid needl e assy
Mark
12WIDER4
15 WIDER4
20 WIDER4
25 WIDER4
15 WIDER4
Spray
width Distance
mm (in)
250 (9.8)
200 (7.9)