INSTRUCTION MANUAL
HVLP Spray Gun
Be sure to observe warning s and cautions in this instruction manual.
If not, it can cause paint ej e cti o n and serious bodil y injury by drawing organic sol v ent.
Be sure to observe fol l owing
marked items which are especiall y important.
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the
minimum necessary conditions. Follow national and local regulations regarding fire prevention,
electricity and safety as well as your own company regulations.
Symbol Marking on the Spray Gun:
This ANEST IWATA spray gun
complies with 2014/34/EU Directive
relating to equipment and protective
systems intended for use in explosive
potentially atmospheres.
Important specifications
Max. Pressure
0.70MPa / 7.0bar / 100psi
Noise l e vel
79dB(A)
Spray conditi o n
Recommended
Measuring point
1m backwards from spray gun, 1.6m hei g ht
Max. temperature
Atmosphere: 5°C~40°C(41°F~104°F)
Important
Never connect pressure feeding paint except pressure feed type spray gun.
Main specifications
Type of
Nozzle orifice
Model
feed
Φ mm (in)
WIDER1L-12G2P
Pressure 1.2 (0.047)
WIDER1L-2-12J2S
1.2 (0.047)
-14J2S
Suction
1.4 (0.055)
-16J2S
1.6 (0.063)
WIDER1L-2-12J2G
1.2 (0.047)
-14J2G
1.4 (0.055)
Gravity
-16J2G
1.6 (0.063)
*1.Atomizing air pressure means air pressure at spray gun inlet when trigger is pulled and air flows.
*2. Tested with 16 s/Ford cup #4 automotive repair paint.
Công ty TNHH MTV Thương mại Công nghệ VI GO VIỆT.
Địa chỉ: 181C, Tổ 2, Khu Phố 3, Phường Long Bình, Biên Hòa, Đồng Nai.
Điện thoại: 0251.2222.135 - Di động: 0938.010.892 - 0988.305.300
Email: vigoviet@gmail.com, MST: 3603113168
Website: http://sungsondongnai.com hoặc http://vigoviet.com hoặc http://airbrush.com.vn
II 2 G Ex h X
II
Complies
Specific
Group II
Category
with
Marking for
(Surface)
(Zone 1&2)
European
Explosion
Directive
Protective
Air and Flui d : 5°C~43°C(41°F~109°F)
Fluid nozzle
Mark
Air cap assy Mark
W1L
WIDER1L-G2
W1L-2
WIDER1L-2-J2
2
G
Ex h
Type of
Ignition
Explosion
Atmosphere
Protection
Group
(GAS)
(not appl i ed)
(Ethylene)
Model
WIDER1L-12G2P
WIDER1L-2-12J2S/G
WIDER1L-2-14J2S/G
WIDER1L-2-16J2S/G
Recommended condition
*1Atomizing air
Air pressure
Fluid output
pressure
inside air cap
MPa (bar/PSI)
MPa (bar/PSI)
ml/min
0.34
0.07
(3.4 / 49.3)
(0.7 / 10)
*2
*2
0.10
0.05
*2
(1.0 / 14.5)
(0.5 / 7.1)
*2
*2
0.13
0.07
(1.3 / 18.9)
(0.7 / 10)
- 1 -
Thi s manual contai n s IMPORTANT
WARNINGS and INSTRUCTIONS.
Equi p ment i n thi s manual i s excl u si v el y for
pai n ti n g purposes.
Do not use for other purposes.
The operator shal l be ful l y conversant wi t h
the requi r ements stated i n thi s i n structi o n
manual i n cl u di n g i m portant warni n gs,
cauti o ns and operati o n and correct handli n g.
Read and understand the i n structi o n
manual , before use and retai n for reference.
IIB
T6
Gb
Temperature
Explosion
Additional
Class
Protection
conditions:
(≤ 85°C)
level
Any static
(EPL)
Electricity
shoul d be
discharged
and needs to
be diverted to
the ground via
a conductive
air hose not
included.
Nozzl e needl e assy combination
Fluid nozzl e
Orifice Φ mm (in)
Φ 1.2 (0.047)
Φ 1.2 (0.047)
Φ 1.4 (0.055)
Φ 1.6 (0.063)
Air
consumption
Pattern width
l/min (cfm)
mm (in)
350
530 (18.7)
270 (10.6)
60
*2
170(6.7)
80
*2
180 (7.1)
200 (7.1)
95
*2
190 (7.5)
80
*2
200(7.9)
130
*2
220 (8.7)
100
240 (8.5)
220 (8.7)
T
Amb
X
+5°C +40°C
Ambient
Temperature
Fluid needl e
Mark
Mark
/ W1L / 12
08H WIDER1
/ W1L-2 / 12
/ W1L-2 / 14
13 WIDER1
/ W1L-2 / 16
18 WIDER1
Air & fluid
Mass
connection
g (lbs.)
Air
G1/4
(NPS1/4)
290
(0.64)
Fluid
G1/4
(NPS1/4)
Need help?
Do you have a question about the WIDER1L-12G2P and is the answer not in the manual?
Questions and answers