Advertisement
Quick Links
1500 Hutch
Hudson Elm finish | Model 5427429
Teknik
www.teknikoffice.co.uk
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 574315
Purchased: __________________
01/27/22
Advertisement
Related Manuals for Teknik 5427429
Summary of Contents for Teknik 5427429
- Page 1 Teknik www.teknikoffice.co.uk 1500 Hutch NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Hudson Elm finish | Model 5427429 PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Lot # 574315 01/27/22 Purchased: __________________...
- Page 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 6-24 Hammer Not actual size Français 25-28 Español 29-32 Safety 33-34 Tape Measure Warranty Optional Accessory (sold separately) å...
- Page 3 Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT END (1) OUTER DOOR (2) TOP (1)
- Page 4 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. ANGLE 42F WOOD DOWEL - 4 HIDDEN CAM - 14 CAM DOWEL - 14 BRACKET - 4 13H STRAIGHT HINGE - 4 40H CURVED HINGE - 4 10M TOUCH-UP PEN - 1 29M BUMPER CARD - 2 TAPE CARD/...
- Page 5 Hardware Usage Guide HOW TO USE A HIDDEN CAM & CAM DOWEL Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Cam Dowel Arrow Hole Push a HIDDEN CAM into Metal end the part. The arrow in the HIDDEN CAM must point toward the hole in the edge Hidden Cam...
- Page 6 Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Just think. The sooner you do this, the sooner å Push six HIDDEN CAMS (1F) into the UPPER BACK (F). you do something else.
- Page 7 Step Step 2 å Flip over the UPPER BACK (F) as shown. å Fasten the FIXED SHELF (D) to the UPPER BACK (F). Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S). å NOTE: You should start each SCREW a few turns before completely tightening any of them.
- Page 8 Step Step 3 å Push eight HIDDEN CAMS (1F) into the LOWER BACK (H). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Arrow Metal end Arrow Metal end Arrow...
- Page 9 Step Step 4 å Flip the LOWER BACK (H) over. å Push the FIXED SHELF (D) onto the CAM DOWELS in the LOWER BACK (H). å NOTE: Do not tighten the HIDDEN CAMS in this step. Page 9...
- Page 10 Step Step 5 å Insert two WOOD DOWELS (42F) into the ENDS (A and B). å NOTE: You may need to gently tap the WOOD DOWELS in with your hammer. å Insert the metal end of two CAM DOWELS (2F) into the holes shown in the UPPER BACK (F). å...
- Page 11 Step Step 6 å Fasten the UPRIGHT (C) to the FIXED SHELF (D). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). å NOTE: You should start each SCREW a few turns before completely tightening any of them. å If you purchased the LED Light (426494), push a CORD CLIP (4P) into the hole in the FIXED SHELF (D). å...
- Page 12 Step Step 7 å Insert two WOOD DOWELS (42F) into the ENDS (A and B). å NOTE: You may need to gently tap the WOOD DOWELS in with your hammer. å Insert the plastic end of four CAM DOWELS (2F) into the holes shown in the TOP (J). å...
- Page 13 Step Step 8 å Fasten the ANGLE BRACKETS (5G) to the FIXED SHELF (D). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the SHELF MOLDING (G) to the ANGLE BRACKETS (5G) as shown. Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 109P å...
- Page 14 Step Step 9 å Fasten the STRAIGHT HINGES (13H) to the OUTER DOORS (E). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (8 used in this step) Page 14...
- Page 15 Step 10 å Carefully stand your unit upright. å Fasten the BACKS to the ENDS (A and B), FIXED SHELF (D), and TOP (J). Tighten fourteen HIDDEN CAMS. å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram.
- Page 16 Step 11 å Fasten the CURVED HINGES (40H) to the INNER DOORS (K). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). Now might be a good time to refresh your drink. BLACK 1/2" FLAT HEAD SCREW (8 used in this step) Page 16...
- Page 17 Step Step 12 å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the adjusting screw and mounting screw to slide it against the stops. Then tighten the mounting screw. å...
- Page 18 Step Step 13 å Refer to the enlarged diagram to identify the parts on the HINGE. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOOR from side to side (horizontal), turn the adjusting screw in or out. å...
- Page 19 Step 14 å You have the option to have the Hutch on the 427415 or 427424. å This book will show the Hutch being attached to the 427424. å Carefully lay your unit onto its back edges. å Open the TAPE CARD/PREP PAD KIT (182M). Peel four double stick strips from the TAPE CARD and stick them onto the bottom edges of the ENDS (A and B) as shown.
- Page 20 Step 15 å Open the Alcohol Prep Pad to wipe the top surface of the 427424 or 427415 Desk as shown. Wipe the top surface of the Desk in this area. 182M Page 20...
- Page 21 Step 16 å IMPORTANT: The Hutch cannot be moved after it is set in place. Pre-plan the Hutch placement, then place it completely on the Hey! It's starting to look attaching surface. like something! å With the help of another person, carefully center the Hutch onto your 427424 or 427415 Desk.
- Page 22 Step 17 å Position your unit in its final location. å Open the FURNITURE TIPPING RESTRAINT KIT (97) and fasten the SAFETY STRAP to the TOP (J). There is no pre- drilled hole. Use extra force when turning the provided short screw into your desired location in the TOP. å...
- Page 23 Step 18 å NOTE: Do not turn the SAFETY DRYWALL ANCHOR into a wall stud. If you prefer to fasten the SAFETY STRAP to a wall stud, go to your local hardware store for proper hardware. å INSTALLATION INSTRUCTIONS: 1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and the end of the SAFETY STRAP. 2.
- Page 24 Step 19 å Using your hammer, gently tap a CAM COVER (129P) onto each visible HIDDEN CAM. å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. å Insert the HOLE PLUG (126P) into the unused hole. å...