Related Manuals for Teknik City Centre 5427120
Summary of Contents for Teknik City Centre 5427120
- Page 1 Teknik For all your newfangled gadgetry. City Centre Desk Model 5427120...
-
Page 2: Table Of Contents
Table of Contents Assembly Tools Required Hardware Identification No. 2 Phillips Screwdriver Part Identification Tip Shown Actual Size Assembly Steps 4-12 Français 13-14 Español 15-16 Safety 17-18 Warranty Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. L-WRENCH - 1 5/16"... - Page 3 Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. REAR LEFT LEG (1) REAR CENTER LEG (1) CENTER MOLDING (1)
-
Page 4: Wrench
Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. Just think. The sooner you do this, the sooner å Fasten the LEFT LEGS (A and B) to the LEFT MOLDING (C). Tighten you do something else. - Page 5 Step 2 å Fasten the CENTER LEGS (D and E) to the RIGHT MOLDING (F). Tighten four 5/16" HEX HEAD SCREWS (2) using the L-WRENCH (1). å NOTE: You should start each SCREW a few turns before completely tightening any of them. 5/16"...
- Page 6 Step 3 å Fasten the MOLDINGS (C and F) to the CENTER MOLDING (G). Tighten four 5/16" HEX HEAD SCREWS (2) using the L-WRENCH (1). å NOTE: You should start each SCREW a few turns before completely tightening any of them. 5/16"...
-
Page 7: 13/16" Hex Head Screw
Step 4 å Fasten the LEGS (A, B, D, and E) to the TOP (H). Tighten eight 13/16" HEX HEAD SCREWS (3) using the L-WRENCH (1). Now might be a good time to refresh å NOTE: You should start each SCREW a few turns before your drink. - Page 8 Step 5 å Fasten the RIGHT LEGS (K) to the TOP (H). Tighten four 13/16" HEX HEAD SCREWS (3) using the L-WRENCH (1). å NOTE: You should start each SCREW a few turns before completely tightening any of them. 13/16" HEX HEAD SCREW (4 used in this step) Page 8...
-
Page 9: 3/8" Pan Head Screw
Step 6 å Fasten a SHELF (J) to the LEGS (D, E, and K). Use eight 3/8" PAN HEAD SCREWS (4). å NOTE: You should start each SCREW a few turns before completely tightening any of them. 3/8" PAN HEAD SCREW (8 used in this step) Page 9... - Page 10 Step 7 å Fasten a SHELF (J) to the LEGS (D, E, and K). Use eight 3/8" PAN HEAD SCREWS (4). å NOTE: You should start each SCREW a few turns before completely tightening any of them. 3/8" PAN HEAD SCREW (8 used in this step) Page 10...
- Page 11 Step 8 å Fasten the remaining SHELF (J) to the LEGS (D, E, and K). Use eight 3/8" PAN HEAD SCREWS (4). If you're doing this to help a friend, don't å NOTE: You should start each SCREW a few turns before leave without a bite.
- Page 12 Step 9 å Carefully stand your unit upright. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with a damp cloth. Wipe dry. Page 12...
- Page 13 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...