Summary of Contents for Teknik Hudson Elm finish 5427422
Page 1
Teknik www.teknikoffice.co.uk 1800x600 Desk NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Hudson Elm finish | Model 5427422 PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Lot # 566752 09/08/21 Purchased: __________________...
Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Optional Accessories Hardware Usage Guide Hammer Not actual size Assembly Steps 6-24 Français 25-28 Español 29-32 Safety 33-34 Warranty Page 2...
Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT END (1) LEFT END (1) SMALL END (1)
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 41G PLATE - 2 LEVELER - 6 WOOD DOWEL - 13 86G SUPPORT BRACKET - 2 GROMMET - 2 GROMMET CAP- 2 TOUCH-UP PEN - 1 TWIST-LOCK®...
Optional Accessories (sold separately) This piece of furniture accommodates one or more of the following optional accessories (sold å Powered Grommet (Item 5427829) separately). å Articulating Keyboard Shelf (Item 5426468) å The Articulating Keyboard Shelf is designed to be fastened to the underside of your desk, desk return, or credenza top. LED Light (Item 5426494) å...
Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the large hole in the part. into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
Page 7
Step 2 å If you purchased the 427413 to fasten to this desk 427422, then follow Steps 3-7. Next, go to the 427413 assembly and attachment. å If you purchased the 427468 or the 427427 to fasten to this desk 427422 on the left, then follow Steps 8-13. å...
Page 8
Step 3 å Fasten the ENDS (A and B) to the MODESTY PANEL (D). Tighten six TWIST-LOCK® FASTENERS. Remember: Righty tighty. å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL Lefty loosey. insert into the ENDS. å NOTE: You will not use the SMALL END (C) in Steps 3-7. Extra hardware has been provided for the SMALL END if needed.
Page 9
Step 4 å Insert seven WOOD DOWELS (42F) into the exact holes Caution shown in the TOP (E). å NOTE: You may need to gently tap the WOOD DOWELS in Two person with your hammer. lift required å With the help of another person, fasten the ENDS (A and B) and MODESTY PANEL (D) to the TOP (E).
Page 10
Step 5 å Fasten the SUPPORT BRACKETS (86G) to the MODESTY PANEL (D) and TOP (E). Use twelve BLACK 9/16" LARGE HEAD SCREWS (1S). å Push four CORD CLIPS (9P) into the TOP (E). BLACK 9/16" LARGE HEAD SCREW (12 used in this step) Page 10...
Page 11
Step 6 å Using your hammer, gently tap four LEVELERS (46E) completely into the holes in the ENDS (A and B). Now might be a good time to refresh å NOTE: Adjustments to the LEVELERS will be made later in your drink.
Page 12
Step 7 å Carefully stand your unit upright. å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward. To lower a corner of your unit, rotate the LEVELER upward. å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. å...
Page 13
Step 8 å Fasten the ENDS (A and C) to the MODESTY PANEL (D). Tighten six TWIST-LOCK® FASTENERS. Remember: Righty tighty. å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL Lefty loosey. insert into the ENDS. å NOTE: You will not use the LEFT END (B) in Steps 8-13. Extra hardware has been provided for the LEFT END if needed.
Page 14
Step 9 å Insert seven WOOD DOWELS (42F) into the exact holes Caution shown in the TOP (E). å NOTE: You may need to gently tap the WOOD DOWELS in Two person with your hammer. lift required å With the help of another person, fasten the ENDS (A and C) and MODESTY PANEL (D) to the TOP (E).
Page 15
Step 10 å Fasten the SUPPORT BRACKETS (86G) to the MODESTY PANEL (D) and TOP (E). Use twelve BLACK 9/16" LARGE Now might be a HEAD SCREWS (1S). good time to refresh your drink. å Push four CORD CLIPS (9P) into the TOP (E). BLACK 9/16"...
Page 16
Step 11 å Using your hammer, gently tap four LEVELERS (46E) completely into the holes in the ENDS (A and C). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. å Fasten the PLATES (41G) to the TOP (E).
Page 17
Step 12 å Carefully stand your unit upright. å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward. To lower a corner of your unit, rotate the LEVELER upward. å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. å...
Page 18
Step 13 å Fasten the 427427 Desk or the 427468 Desk to your 427422 on the left. Use four 9/16" BLACK LARGE HEAD SCREWS (1S) through the PLATES and into the adjoining Desk. å NOTE: Please read the back pages of the instruction booklet for important safety information. å...
Page 19
Step 14 å Fasten the ENDS (B and C) to the MODESTY PANEL (D). Tighten six TWIST-LOCK® FASTENERS. Remember: Righty tighty. å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL Lefty loosey. insert into the ENDS. å NOTE: You will not use the RIGHT END (A) in Steps 14-19. Extra hardware has been provided for the RIGHT END if needed.
Page 20
Step 15 å Insert seven WOOD DOWELS (42F) into the exact holes Caution shown in the TOP (E). å NOTE: You may need to gently tap the WOOD DOWELS in Two person with your hammer. lift required å With the help of another person, fasten the ENDS (B and C) and MODESTY PANEL (D) to the TOP (E).
Page 21
Step 16 å Fasten the SUPPORT BRACKETS (86G) to the MODESTY PANEL (D) and TOP (E). Use twelve BLACK 9/16" LARGE Now might be a HEAD SCREWS (1S). good time to refresh your drink. å Push four CORD CLIPS (9P) into the TOP (E). BLACK 9/16"...
Page 22
Step 17 å Using your hammer, gently tap four LEVELERS (46E) completely into the holes in the ENDS (B and C). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. å Fasten the PLATES (41G) to the TOP (E).
Page 23
Step 18 å Carefully stand your unit upright. å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward. To lower a corner of your unit, rotate the LEVELER upward. å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. å...
Page 24
Step 19 Fasten the 5427427 Desk or the 5427468 Desk to your 5427422 on the right. Us e four 9/16" BLACK å LARGE HEAD SCREWS (1S) through the PLATES and into the adjoining Desk. NOTE: Please read the back pages of the instruction booklet for important safety information. å...