Advertisement
Quick Links
Teknik
www.teknikoffice.co.uk
1200x600 Desk
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
Hudson Elm finish | Model 5427414
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
English pg 1-27
Français pg 28-31
Español pg 32-35
Lot # 573163
10/28/21
Purchased:
__________________
Advertisement
Related Manuals for Teknik Office Affiliate 5427414
Summary of Contents for Teknik Office Affiliate 5427414
- Page 1 Teknik www.teknikoffice.co.uk 1200x600 Desk NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Hudson Elm finish | Model 5427414 PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-27 Français pg 28-31 Español pg 32-35 Lot # 573163 10/28/21 Purchased: __________________...
- Page 2 Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Optional Accessories Hardware Usage Guide 7, 14, 21 Hammer Assembly Steps 6-27 Not actual size Français 28-31 Español 32-35 Safety 36-38 Warranty Page 2...
- Page 3 Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT END (1) LEFT END (1) SMALL END (1)
- Page 4 Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 46E LEVELER - 6 42F WOOD DOWEL - 12 41G PLATE - 2 GROMMET 10M TOUCH-UP PEN - 1 GROMMET - 2 CAP - 2 TWIST-LOCK®...
- Page 5 Optional Accessories (sold separately) å This piece of furniture accommodates one or more of the following optional accessories (sold separately). Powered Grommet (Item 427829) å Articulating Keyboard Shelf (Item 426468) å The Articulating Keyboard Shelf is designed to be fastened to the underside of your desk, desk return, or credenza top. LED Light (Item 426494) å...
- Page 6 Step 1 å See below for the options with your unit. Steps 2 - 8 Steps 9 - 15 Steps 16 - 22 Page 6...
- Page 7 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 8 Step 3 å Using your hammer, gently tap four LEVELERS (46E) completely into the holes in the ENDS (A and B). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. Page 8...
- Page 9 Step 4 å Fasten the MODESTY PANEL (E) to the RIGHT END (A). Tighten three TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL insert into the END. å Fasten the LEFT END (B) to the MODESTY PANEL (E). Tighten three TWIST-LOCK® FASTENERS. å...
- Page 10 Step 5 å Turn two CORD CLIPS (9P) into the TOP (D). å NOTE: The CORD CLIP is used to hold your cords against the TOP. Pilot hole to be used only if you purchased the optional 426468 Articulating Keyboard Shelf. Page 10...
- Page 11 Step 6 å Insert six WOOD DOWELS (42F) into the holes in the edges of the ENDS (A and B) and MODESTY PANEL (E). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer. å With someone's help, fasten the TOP (D) to the ENDS (A and B) and MODESTY PANEL (E).
- Page 12 Step 7 å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward. To lower a corner of your unit, rotate the LEVELER upward. å Insert a GROMMET (2P) and GROMMET CAP (3P) into each large hole in the TOP (D).
- Page 13 Step 8 å For long-term care and maintenance of your unit, you may touch up the edges with the TOUCH-UP PEN (10M). å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. å NOTE: Please read the back pages of the instruction booklet for important safety information. å...
- Page 14 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 15 Step 10 å Using your hammer, gently tap four LEVELERS (46E) completely into the holes in the ENDS (B and C). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. Page 15...
- Page 16 Step 11 å Fasten the MODESTY PANEL (E) to the SMALL END (C). Tighten three TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL insert into the END. å Fasten the LEFT END (B) to the MODESTY PANEL (E). Tighten three TWIST-LOCK® FASTENERS. å...
- Page 17 Step 12 å Turn two CORD CLIPS (9P) into the TOP (D). å NOTE: The CORD CLIP is used to hold your cords against the TOP. Pilot hole to be used only if you purchased the optional 426468 Articulating Keyboard Shelf. Page 17...
- Page 18 Step 13 å Insert six WOOD DOWELS (42F) into the holes in the edges of the ENDS (B and C) and MODESTY PANEL (E). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer. å With someone's help, fasten the TOP (D) to the ENDS (B and C) and MODESTY PANEL (E).
- Page 19 Step 14 å Fasten the TOP (D) to the TOP of the other desk. Use two PLATES (41G) and eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward.
- Page 20 Step 15 å For long-term care and maintenance of your unit, you may touch up the edges with the TOUCH-UP PEN (10M). å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. å NOTE: Please read the back pages of the instruction booklet for important safety information. å...
- Page 21 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® Push a TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the into the large hole in the part. hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 22 Step 17 å Using your hammer, gently tap four LEVELERS (46E) completely into the holes in the ENDS (A and C). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. Page 22...
- Page 23 Step 18 å Fasten the MODESTY PANEL (E) to the RIGHT END (A). Tighten three TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL insert into the END. å Fasten the SMALL END (C) to the MODESTY PANEL (E). Tighten three TWIST-LOCK® FASTENERS. å...
- Page 24 Step 19 å Turn two CORD CLIPS (9P) into the TOP (D). å NOTE: The CORD CLIP is used to hold your cords against the TOP. Pilot hole to be used only if you purchased the optional 426468 Articulating Keyboard Shelf. Page 24...
- Page 25 Step 20 å Insert six WOOD DOWELS (42F) into the holes in the edges of the ENDS (A and C) and MODESTY PANEL (E). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer. å With someone's help, fasten the TOP (D) to the ENDS (A and C) and MODESTY PANEL (E).
- Page 26 Step 21 å Fasten the TOP (D) to the TOP of the other desk. Use two PLATES (41G) and eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward.
- Page 27 Step 22 å For long-term care and maintenance of your unit, you may touch up the edges with the TOUCH-UP PEN (10M). å Using your hammer, gently tap a TWIST-LOCK® FASTENER COVER (125P) onto each visible TWIST-LOCK® FASTENER. å NOTE: Please read the back pages of the instruction booklet for important safety information. å...