Advertisement
Quick Links
1800x900 Bow
Front Desk
Hudson Elm finish | Model 5427468
Teknik
www.teknikoffice.co.uk
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
English pg 1-14
Français pg 15-17
Español pg 18-20
Lot # 566975
Purchased:
__________________
09/22/21
Advertisement
Related Manuals for Teknik Office Affiliate 5427468
Summary of Contents for Teknik Office Affiliate 5427468
- Page 1 Teknik www.teknikoffice.co.uk 1800x900 Bow NOTE: THIS INSTRUCTION BOOKLET CONTAINS Front Desk IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Hudson Elm finish | Model 5427468 English pg 1-14 Français pg 15-17 Español pg 18-20 Lot # 566975 09/22/21...
- Page 2 Table of Contents Assembly Tools Required Hardware Identification No. 2 Phillips Screwdriver Part Identification Tip Shown Actual Size Optional Accessories Hardware Usage Guide Hammer Not actual size Assembly Steps 5-14 Français 15-17 Español 18-20 Safety 21-22 Warranty Hardware Identification å Screws are shown actual size.
- Page 3 Now you know Part Identification our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts. RIGHT END (1) LEFT END (1) TOP (1)
- Page 4 Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Insert fourteen WOOD DOWELS (42F) into the exact holes shown in the TOP (C). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer.
- Page 5 Hardware Usage Guide HOW TO USE A TWIST-LOCK FASTENER ® 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. If the TWIST-LOCK® FASTENER NOTE: The dowel end of the FASTENER must is already inserted in the part, remain fully inserted in the hole of the adjoining be sure both the dowel end and part while locking the FASTENER.
- Page 6 Step 3 å Fasten the RIGHT END (A) and RIGHT UPRIGHT (D) to the TOP (C). Tighten four TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the TOP insert into the END, UPRIGHT, and BACK (E). Curved edge Page 7...
- Page 7 Step 4 å Fasten the MODESTY PANEL (F) to the TOP (C). Tighten three TWIST-LOCK® FASTENERS. S u r f a c i t h I S T - L O F A S T E N ® E R S Page 8...
- Page 8 Step 5 å Insert four WOOD DOWELS (42F) into the exact holes shown in one BACK (E). å NOTE: You may need to gently tap the WOOD DOWEL in with your hammer. å Fasten the LEFT END (B) and LEFT UPRIGHT (G) to the BACK (E).
- Page 9 Step 6 å Fasten the LEFT END (B) and LEFT UPRIGHT (G) to the TOP (C). Tighten four TWIST-LOCK® FASTENERS. å NOTE: Be sure the WOOD DOWELS in the TOP insert into the END, UPRIGHT, and BACK (E). Page 10...
- Page 10 Step 7 å Fasten the UPRIGHTS (D and G) to the MODESTY PANEL (F). Use six BLACK 1-15/16" FLAT HEAD SCREWS (113S). å NOTE: You should start each SCREW a few turns before completely tightening any of them. 113S 113S BLACK 1-15/16"...
- Page 11 Step 8 å Using your hammer, gently tap eight LEVELERS (46E) completely into the holes in the ENDS (A and B) and UPRIGHTS (D and G). å NOTE: Adjustments to the LEVELERS will be made later in assembly once your unit is standing upright. å...
- Page 12 Step 9 å With someone's help, carefully stand your unit upright. Pro Tip: Lift with your å The 427468 Executive Desk may be placed in a variety legs. And, you know, of configurations with other units as shown in the your arms.
- Page 13 Step 10 å Your unit may need leveling. To raise a corner of your unit, rotate the LEVELER downward. To lower a corner of your unit, rotate the LEVELER upward. å For long-term care and maintenance of your unit, you may touch up the edges with the TOUCH-UP PEN (10M). å...