Table of Contents
Advertisement
12.0 - ADDING NEW DEVICES
To carry out the operation successfully, make sure the required electrical connections
!
(bonnet switch and ignition) have been made.
To activate the procedure proceed as follows:
• With the system disarmed, open the bonnet and leave it open.
The "ON-OFF" ignition cycles must be carried out within 4 seconds otherwise the
!
• Cycle ignition key "ON-OFF"-"ON-OFF"-"ON-OFF"-"ON" (on the last turn, leave it "ON").
• To confirm it has entered in learn mode, the system gives 1 Beep and 1 Bop, the turn indicators flash
once and the LED turns ON.
Do not close the bonnet otherwise all previously programmed devices will be erased
!
as described in the next paragraph.
• Touch the override key to the receptacle; each time a device is learned a Beep sounds and the
status LED turns OFF briefly.
• Repeat this procedure to learn other devices.
• Cycle ignition key OFF, the end of the procedure is confirmed by a Bop and a flash of the turn
indicators. The status LED powers OFF.
Storing memory is for 55 devices. If an extra device is added it automatically deletes the
!
first device stored in the alarm memory.
13.0 - DELETING PROGRAMMED DEVICES
To carry out the operation successfully, make sure the required electrical connections
!
(bonnet switch and ignition) have been made.
All devices stored in the system memory can be erased; to clear memory proceed as follows:
• With the system disarmed, open and keep opened the vehicle bonnet.
The "ON-OFF" ignition cycles must be carried out within 4 seconds otherwise the
!
• Cycle ignition key "ON-OFF"-"ON-OFF"-"ON-OFF"-"ON" (on the last turn leave it "ON").
• To confirm it has entered in delete mode, the system gives 1 Beep and 1 Bop, the turn indicators
flash once and the LED turns ON.
• Close the bonnet and keep it closed for approx. 8 sec. until the devices are completely deleted.
!
If the bonnet is opened before 8 seconds, the devices will not be deleted.
• The status LED turns OFF to confirm the devices have been deleted; turn ignition key OFF.
• The end of the procedure is signaled by 1 long Bop.
PAGE 14 - INSTALLER MANUAL
procedure is invalidated.
procedure is invalidated.
14.0 - ULTRASONIC VOLUMETRIC PROTECTION
Insert the WHITE connector in the "W" marked socket and the RED connector in the "R" marked
socket (see figure below).
Install the ultrasonic sensors on the top part of the windshield internal pillars, away from the air vents
and point them towards the center of the rear window.
To check the sensitivity level proceed as follows:
• With the alarm system disarmed, roll down the front window approx. 20 cm.
• Adjust the trimmer at a medium setting.
• Close all doors, bonnet and boot and arm the system.
• During the arming delay introduce an object in the cabin through the window and move it around;
the status LED will turn OFF to signal a presence.
• If the sensitivity level is too high or too low, readjust the trimmer and repeat the above procedure.
SENSITIVITY
ADJUSTMENT
15.0 - SYSTEM RESET
By activating the following procedure, the system returns to the factory default settings.
!
This procedure must therefore only be used in case of need.
Reset procedure will clear the turn indicators flashes if previously learnt.
To reset the system proceed as follows:
• Disconnect the alarm power supply.
• Short-circuit the RED and BLACK wires of the 2-pin LED connector.
• Power the system; 4 Beeps and 4 flashes of the turn indicators will confirm the operation.
• Remove the previously created short-circuit; the status LED lights up steady.
• Cycle ignition key ON; reset is confirmed by a Beep and the siren will sound for approx. 3 sec.
• Cycle ignition key OFF; the LED will power off. There are no acoustic signals to confirm the end of
the procedure.
14.1
- CONNECTION AND POSITIONING
14.2
- SENSOR ADJUSTMENT
ULTRASONIC
CELLS
INSTALLER MANUAL - PAGE 15
Advertisement
Table of Contents
