Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GLP Impression X5 IP Bar 1000
Summary of Contents for GLP Impression X5 IP Bar 1000
- Page 1 X5 IP Bar 1000 Software v.1.1.3 Rev. 20230815-01...
- Page 2 Manual for the impression X5 IP Bar 1000. Covers firmware v. 1.1.3 GLP® impression X5 IP Bar 1000 Quick Start and Safety Manual – Revision 20230815-01 © 2023 German Light Products GmbH. All rights reserved. The marks ‘GLP’ and ‘German Light Products’ are trademarks registered as the property of German Light Products GmbH in Germany, in the United States of America and in other countries.
-
Page 3: Table Of Contents
Avoiding damage from light sources and heat ......10 Avoiding damage from dust and airborne particles ....11 Transportation and storage ............... 11 3. impression X5 IP Bar 1000 overview ............12 4. Features ........................13 User Manual ......................13 Tilt lock ........................13 5. -
Page 4: Safety
All documents are available for download from www.glp.de. The impression X5 IP Bar 1000 is intended for use by experienced professionals with the knowledge and skills to set up, operate, and maintain high-powered, remotely controlled lighting equipment safely and efficiently. These operations require expertise that may not be provided in this Manual or in the User Manual. -
Page 5: Electrical Safety
• Check the GLP website at www.glp.de and make sure that you have the latest version of this manual. Check the fixture software version indicated on page 2 of this manual and then use the fixture’s control panel to check the version installed... -
Page 6: Fire Safety And Protection From Burns
16 A-rated, 3 x 1.5 mm H07RN-F type cable. Do not connect more than two (2) impression X5 IP Bar 1000 fixtures linked together in a chain to power at 100-120 V, 60 Hz. -
Page 7: Eye Safety
Eye safety • The impression X5 IP Bar 1000 is classified as a Risk Group 2 lighting fixture according to EN 62471 at a distance of 1 m (3.3 ft.). Possibly hazardous radiation emitted. -
Page 8: Installation Safety And Protection From Personal Injury
X5 IP Bar 1000 • Comply with local regulations on the use of strobe lighting and notify the public in advance with highly visible warning signs when strobe effects are used. • If a seizure occurs, stop using strobe effects. Seek professional medical help. Note the time that the seizure starts and finishes. - Page 9 • If the fixture becomes damaged, stop using it immediately and disconnect it from power. Do not attempt to use a fixture that is obviously damaged. • Do not modify the fixture in any way not described in its user documentation. • Install genuine GLP parts only. Rev. 20230811-01...
-
Page 10: Avoiding Damage To The Fixture
X5 IP Bar 1000 2. Avoiding damage to the fixture Important! Follow the directions in this section carefully, or the fixture may suffer damage that is not covered by the product warranty. General precautions • Do not drop the fixture or expose it to mechanical stress. -
Page 11: Avoiding Damage From Dust And Airborne Particles
X5 IP Bar 1000 • Do not operate the fixture in ambient temperatures outside the range -10° C (14°F) to 45° C (113°F). • Allow free airflow around the fixture. Avoiding damage from dust and airborne particles • Carry out regular visual inspections of the fixture to make sure that there is no accumulation of dirt, especially on the front of the fixture and around air vents. -
Page 12: Impression X5 Ip Bar 1000 Overview
X5 IP Bar 1000 3. impression X5 IP Bar 1000 overview Figure 2. impression X5 Bar IP 1000 overview A – Head B – Air vent (x 4) C – Alignment pins button D – AC mains power IN (Neutrik powerCON TRUE1 TOP) E –... -
Page 13: Features
The impression X5 IP Bar 1000 has a tilt lock that can be used to prevent the head from moving while the fixture is being carried. The tilt lock also lets you immobilize the head during cleaning or while installing optical accessories on the front of the fixture. -
Page 14: Installation
Mounting options An impression X5 IP Bar 1000 fixture may be installed in one of the following ways: Standing horizontally on a horizontal surface. Fastened to a rigging truss or similar structure at any angle using the supplied brackets and two or more rigging clamps (optional accessories). -
Page 15: End-To-End Alignment
14. Installing on a rigging truss or similar structure You can suspend an impression X5 IP Bar 1000 fixture from a rigging truss or pipe using the two brackets that are supplied with the fixture and rigging clamps that are available from GLP as optional accessories. - Page 16 X5 IP Bar 1000 To install the impression X5 IP Bar 1000 on a rigging truss or pipe: Check that the truss or pipe is secure and can safely hold ten times the weight that it will support. See Figure 6. Bolt at least one rigging clamp securely to each of the two rigging...
-
Page 17: Ac Mains Power
Cables used for power input and for relaying power to other fixtures must meet the requirements listed under ‘Electrical safety’ on page 5. Power cable The impression X5 IP Bar 1000 is supplied with a power cord with a Neutrik powerCON TRUE1 TOP connector for AC mains power input. Connecting to power The AC mains power supply must include a connection to ground / protective earth. -
Page 18: Connecting Multiple Fixtures To Power In A Chain
Warning! Do not connect more than two (2) impression X5 IP Bar 1000 fixtures in total to power in one chain at 100-120 V, 60 Hz. Do not connect more than four (4) impression X5 IP Bar 1000 fixtures in total to power in one chain at 200-240 V, 50 Hz. -
Page 19: Connecting To Dmx Data
(see recommendations in ‘Avoiding damage to the fixture’ on page 10). The impression X5 IP Bar 1000 supports USITT DMX 512A, Art-Net and sACN DMX control data signal protocols. It also supports RDM (Remote Device Management). The X5 IP Bar 1000 has two 5-pin XLR connectors for IN and THRU connections on a DMX data link using standard DMX protocol. -
Page 20: Starting And Stopping Operation
X5 IP Bar 1000 8. Starting and stopping operation Warning! Before you apply power to the impression X5 IP Bar 1000 or operate it after a blackout, make sure that nobody is looking directly into the front of the fixture and that there is sufficient clearance for the head to tilt safely. -
Page 21: Service
Installing optical accessories The impression X5 IP Bar 1000 has channels in the front of the head for the installation of optical accessories. Impression X5 IP Bar 1000 accessories such as a soft diffuser and an asymmetrical beam shaper are available from GLP. -
Page 22: Glp Service And Support
X5 IP Bar 1000 GLP Service and Support Contact information for the nearest GLP Service and Support is available online at www.glp.de/en/service, by email at info@glp.de, or by telephone at the following numbers: • GLP Germany: +49 (7248) 927 19-55 •... -
Page 23: Technical Specifications
X5 IP Bar 1000 10. Technical specifications Optics and photometrics Light source: 18 x 40 W RGBL LEDs LED lifetime: 50 000 hrs. approx. to > 70% luminous output Output lenses: 18 x square lenses: 48 x 48 mm with 980 x 120 mm aperture... - Page 24 Typical energy consumption: 677 kWh per hour Maximum permitted number of fixtures daisy-chained to power 2 x impression X5 IP Bar 1000 total @ 100-120 V, 60 Hz 4 x impression X5 IP Bar 1000 total @ 200-240 V, 50 Hz...
- Page 25 X5 IP Bar 1000 Connections AC mains power IN and THRU: Neutrik powerCON TRUE1 Standard DMX data link IN and THRU: 5-pin XLR Art-Net and sACN data link IN and THRU: Neutrik etherCON, failsafe link integrity (in preparation) Construction...
-
Page 26: Dimensions
X5 IP Bar 1000 11. Dimensions impression X5 IP Bar 1000 All dimensions are in millimeters impression X5 IP Bar 1000 Quick-Start and Safety Manual...
Need help?
Do you have a question about the Impression X5 IP Bar 1000 and is the answer not in the manual?
Questions and answers