Table of contents Description of the Device ..................4 1.1 Safety Instructions.................... 5 Preparation and Installation................... 6 2.1 Mounting......................6 3 ................6 2.2 Secure the 2.3 Connectors ....................... 6 2.3.1 Power supply ..................6 2.3.2 DMX ....................... 6 2.4 Fuses........................ 6 The Menu Field / DMX Address and Functions ............
Page 4
DMX Channel Selection (DMX Protocol)............. 14 Change the Lamp....................17 5.1 Safety Regulations ..................17 5.2 Realize the Lamp Change................17 Change a Gobo ..................... 17 6.1 Safety Regulations ..................17 6.2 Realize the Gobo Change ................18 3 ..........18 Maintenance and Cleaning the 7.1 Safety Regulations ..................
1 Description of the Device Lens 2x Air inlets Air outlet Display Data entry Casing screws Relay bracket Figure 1-1 German Light Production (instruction version 0.91)
1.1 Safety Instructions 3 is a High-Tech Product. To guarantee a smooth operation, it is necessary to keep the following rules. The manufacturer of this device will not take responsibility of damages through disregard of the information in this manual. Warranty adjustments will be canceled.
2 Preparation and Installation 2.1 Mounting Mount clamps and/or hooks directly to the mounting (relay) brackets of the . Please make sure to use right sized clamps and hooks and fit them securely. Keep a safety distance of 0.5 m towards any easy inflammable materials (decoration etc.).
3 The Menu Field / DMX Address and Functions You find the control board on the front side of the casing. It allows you to make all necessary adjustments of the . With the LED-Display Mode-key you get into the main menu. Afterwards you can navigate through the menu with the Up/Down-keys.
(D001) 3.1 Adjust the DMX- Address 3 you can see the current DMX- Right after turning on the Address. If there is no DMX- Signal the display flashes. D001 For the address setting please follow this procedure: 3 and wait until the fixture reset has finished 1.
3 must If you want to run the systems simultaneously, one of the be switched as the master. All others must be "Slave" Master = OFF. Notice: The Audio function is only working if no DMX is connected. This function can work e.g. on small events or as an emergency program.
(RTLT) 3.8 Invert Tilt Movement RTLT This function allows you to invert the Tilt movement. Use the Up/Down-keys to select invert . Press Enter to confirm or Mode to cancel. (SPEC) 3.9 Special Functions SPEC This menu allows you to enter further special functions of the In detail they are: (MANU) 3.9.1 Manual Drive...
(LAAU) 3.9.2 Lamp On automatically LAAU This function enables to switch On the lamp automatically after switching On the fixture. Use the Up/Down-keys to select if you want to switch on the lamp automatically after switching on the fixture or if you don't want this function.
(DISP) 3.9.5 Display DISP Use this function to choose between different display indications. Use the Up/Down-keys to select desired function and press Enter to confirm or Mode to cancel and return to the menu. D ON Display On/Off (If you've chosen , the display will go out within 15 seconds after the last input.
(DFSE) 3.9.7 Default Settings DFSE Press Enter to reset all fixture personalities (not the adjusted functions) to the default values. On the display will appear to indicate that the defaults are set. Function Display Default Values D001 D001 DMX Address RPAN Pan reverse RTLT...
4 DMX Channel Selection (DMX Protocol) Channel Function Time and Value 1) PAN- 0 .. 230° min. 2,65 s 0..255 00..FF 0..100 coarse 2) PAN-fine High- Pos ... High- Pos + 2,1° (16 Bit) 0..255 00..FF 0..100 3) Tilt- 0 .. 110° min.
Page 16
Channel Function Time and Value open (slow) 112.127 70..7F 44,1 color rotation, slow-fast, CW min. 1,4 turns/h 128..191 80..BF 50..75 color rotation, fast-slow, CCW max. 2,9 turns/sec. 192..253 C0..FD 76..98 Audio color chaser slow each 4 sound impulse new color Audio color chaser fast each sound impulse new color...
Page 17
Channel Function Time and Value 11) Focus in - out (2m - infinite) full distance 1,5 sec. 0..255 0..FF 0..100 12) Special no function 0..15 00..0F 0..6 Gobo-seesaw+/- 10° 3,5 moves / min. up to 16..31 10..1F 7..12 slow – fast 60 moves / max.
5 Change the Lamp For a frictionless operation please read this chapter carefully and follow all instructions. 5.1 Safety Regulations • Pull out the main plug! • Wait min. 20 minutes after the last operation to cool down the fixture. •...
• Before you put the 3 into operation close the casing, otherwise your retina can be hurt! 6.2 Realize the Gobo Change 1. Open the unit as described in the chapter before. 2. Hold the two Gobo springs aside and remove the Gobo. 3.
Glass gobos monthly soft cloth and glass cleaning fluid Prism monthly soft cloth and glass cleaning fluid Dimmer/Shutter yearly vacuum cleaner, airbrush, etc. Inside lens monthly soft cloth no glass cleaning fluid Fan and air channel monthly vacuum cleaner, airbrush, etc. Reflector never Lamp...