IP rating....................11 Avoiding damage from water and humidity........11 Avoiding damage from dust and airborne particles......12 Transportation and storage..............12 GLP Service and Support..............12 EXO Beam 10 overview ................13 Installation ....................15 Permitted mounting options ...............15 Securing fixtures with a safety cable ..........15 Installing on a rigging truss or similar structure........16...
Page 4
Service Advanced menu ..............30 11. DMX control mode overview ..............31 12. DMX control channel layout tables ............32 DMX Mode 1: Standard ...............32 13. Service ......................35 Cleaning....................35 GLP Service and Support..............35 14. Technical specifications................36 Optics......................36 Control....................36 Installation ....................36 Electrical....................36 Connections ..................36 Construction ..................36...
German Light Products® Safety 1. Safety Key to symbols The following symbols are used in the Fusion EXO Beam 10 lighting fixture’s user documentation: Warning! Safety hazard. Warning! Hazardous voltage. Risk of severe injury or Risk of lethal or severe death.
● Check the GLP website at www.glp.de and make sure that you have the latest version of this manual. Check the fixture software version indicated on page 2 of this manual and then use the fixture’s control panel to check the version installed in the...
- US power cable: 16 A, 14 AWG, UL-listed, E304117, SJT, 4.9 ft. - EU power cable: 16 A, 1.5 mm², H07RN-F, 1.5 m. Do not connect more than six (6) Fusion EXO Beam 10 fixtures to power in a chain at 100-120 V, 60 Hz.
Safety ignite objects that are in contact with the surface. Ensure that the front surface Is clean and unobstructed at all times in order to prevent a fire hazard and damage to the fixture. ● The fixture’s optical components can focus the sun’s rays, creating a risk of fire and damage.
Do not attempt to use a fixture that is obviously damaged. ● Do not modify the fixture in any way not described in its user documentation. ● Install genuine GLP parts only. EXO Beam 10 User Manual Rev. A...
Avoiding damage to the fixture 2. Avoiding damage to the fixture Important! Follow the directions in this section carefully, or the fixture may suffer damage that is not covered by the product warranty. General precautions Do not drop the fixture or expose it to mechanical stress.
German Light Products® Avoiding damage to the fixture IP rating EXO Beam 10 fixtures are IP65-rated: ● IP stands for Ingress (entry into the fixture) Protection. ● The first figure 6 in the rating means that fixtures are protected against the entry of dust and airborne particles.
● Store the fixture in a dry location when not in use. GLP Service and Support Contact information for the nearest GLP Service and Support is available online at www.glp.de/en/service, by email at info@glp.de, or by telephone at the following numbers: ●...
EXO Beam 10 overview 3. EXO Beam 10 overview The Fusion EXO Beam 10 from GLP is a powerful LED-based beam light fixture with fast pan and tilt, 1 degree beam, 14 selectable colors and 14 gobos (seven of which are rotatable).
German Light Products® Installation 4. Installation Warning! Read ‘Safety’ starting on page 5 for important safety information that you must understand before you install or operate the fixture. Install EXO Beam 10 fixtures only as described in this chapter, or you may create an installation that is unsafe.
Installation To secure an EXO Beam 10 fixture with a safety cable: Figure 3. Safety cable attachment Loop a safety cable around a secure anchoring point such as a truss beam or fixed structure so that it will catch the fixture if a rigging clamp fails.
German Light Products® Installation Figure 4. Omega bracket fasteners Attach suitable clamps to the Omega brackets. Line up the fasteners of the Omega bracket with the holes “A” in the base of the EXO Beam 10 as shown in Figure 4. The brackets may be installed either way round so the cabling is in line with the bar or at right angles to it.
AC mains power 5. AC mains power Warning! Read ‘Safety’ starting on page 5 for important safety information that you must understand before you install or operate the fixture. Check that all cables and connectors are suitable for the installation environment and application (see recommendations in ‘Avoiding damage...
German Light Products® AC mains power Installing power connectors If you intend to draw power from convenience receptacles / consumer mains power sockets, it is possible to install a suitable cord cap / power plug on the supplied power cord / input cable. If you do this, check that the cord cap / plug is rated minimum 250 V, 16 A, that it has a connection to ground / earth and that it has an integral cable grip.
DMX input and DMX link out connectors. If you need to split the DMX cable, use a powered DMX splitter. If you would like advice with planning and installing a DMX link, your GLP supplier will be happy to provide assistance.
German Light Products® Starting and stopping operation 7. Starting and stopping operation Warning! Before you apply power to the fixture or operate it after a blackout, make sure that nobody is looking directly into the front of the fixture. The EXO Beam 10’s TRUE1 mains power input connector supports hot-plugging, and connecting and disconnecting a live power cable is an option, especially if you need to shut down power urgently, but it is still good practice to shut down power to the AC mains power circuit before connecting and disconnecting power cables.
Features 8. Features The EXO Beam 10 unit has the following features: Position Pan rotation 630°(3.9 sec) or 540°(4.3 sec),Tilt rotation 267°(2.2 sec) with 16 bit resolution. The fixture will automatically reposition if knocked – this option can be disabled from the menu.
German Light Products® Features Gobo wheel The gobo wheel has 15 positions including open. Seven of the gobos (the even numbers in the diagram below) are rotatable and indexable, the others are fixed. Figure 6. Gobo Wheel Dimming See Figure 7. You can select from two dimming curves using the control panel or the Control / Settings DMX channel: Soft (Gamma) Linear...
Features The default setting is Soft. Strobe / shutter A variety of strobing and fading effects can be produced by the fixture. Prism Two separate prisms allow beam splitting effects. Each prism can be independently inserted in the beam path or removed, and can be continuously rotated in either direction or set to an indexed position.
German Light Products® Control menus and onboard display Control menus and onboard display Warning! DMX control is disabled when the control menus are active. Be prepared for the fixture to emit strong light as soon as you exit the control menus.
Control menus and onboard display DMX control is disabled when the control menus are active. Display options The illuminated LCD display lets you change fixture settings. The display has a battery backup so that you can change the settings before mains is connected to the fixture.
German Light Products® Control menus and onboard display Pan disable / Tilt disable These options allow you to disable the startup reset movements or disable the drive of the pan and/or tilt motors. The options are - Off: Normal motor control - Reset Disabled: The fixture will not do its power on reset sequence on this motor but the motor is still controlled.
Control menu layout 10. Control menu layout Menus Notes 1 - 512 Enter DMX address ADDRESS CONTROL Select DMX control mode Standard – 15 channels MODE Wired DMX control CONTROL Wireless DMX control PROTOCOL WIRELESS (optional module) Pan Invert...
Page 29
German Light Products® Control menu layout Focus 0-255 Prism 1 0-255 Prism 2 0-255 Control 0-255 Press ENTER for 3 sec to Capture Scene capture incoming DMX state Firmware Version ver x.x Fixture firmware version Show fixture serial, RDM Fixture Details Serial …...
Control menu layout Service Advanced menu Hold down Enter for 6 seconds to access this menu. Menus Notes Pan Disable Off/On Tilt Disable Off/On Units °C / °F Tilt Offsets Zoom Power Hours Power Cycles Reset LED Hours Counter...
German Light Products® DMX control mode overview 11. DMX control mode overview The EXO Beam 10 has only one DMX control mode which uses the following DMX channels Mode 1 DMX Mode 1: Standard Compact The EXO Beam 10 uses 15 DMX channels.
DMX control channel layout tables 12. DMX control channel layout tables DMX Mode 1: Standard 11 DMX Channels Default Channel Command range Percent Fade Pan left–right 65535 32767 Fade Pan fine Tilt Tilt up–down 65535 32767 Fade Tilt fine Color 01 –...
Page 33
German Light Products® DMX control channel layout tables Gobo 5 shake and index 36.9 39.2 Snap Gobo 6 shake 39.6 42.0 Snap Gobo 7 shake and index 42.4 44.7 Snap Gobo 8 shake 45.1 47.5 Snap Gobo 9 shake and index 47.8 50.2 Snap...
Page 34
DMX control channel layout tables No prism Variable position from 0-360° 49.8 Rotation stop 50.2 50.2 Rotation clockwise fast > slow 50.6 74.9 14 Prism 2 Fade Rotation stop 75.3 75.3 Rotation counterclockwise slow > 75.7 fast No function...
GLP Service and Support Contact information for the nearest GLP Service and Support is available online at www.glp.de/en/service, by email at info@glp.de, or by telephone at the following numbers: ●...