Table of Contents
Advertisement
Quick Links
Quick Start Guide – VBOX Touch V1: Lap Timing Mode
https://en.racelogic.support//Product_Info/Performance_Meters/VBOX_Touch/VBOX_Touch_V1/
Quick_Start_Guides_%E2%80%93_VBOX_Touch_V1/
Quick_Start_Guide_%E2%80%93_VBOX_Touch_V1%3A_Lap_Timing_Mode
VBOX Touch features a 10 Hz GNSS receiver and a responsive colour touchscreen. The Lap Timing
Mode allows you to view live Lap Timing information in relation to a set Start/Finish line.
Two Lap Timing screens are available; the
live reference lap time comparison (Delta-T), current reference lap time, last lap time, last lap time difference to best,
session time and completed lap count. The
time.
Registration
Please register your VBOX Touch so that Racelogic can
continue to provide you with notifications about the latest
software releases and firmware upgrades for your
Racelogic product, and offer technical support.
Register your device here.
What is in the box?
When you purchase a VBOX Touch Motorsport V1 (RLVBTOUCH-M), you will find the following items when you open
the box:
Product Code
VBTOUCH-V1
Main
Screen, which contains live reference lap speed comparison (Delta-V),
Basic Screen
contains either just a rolling lap time or a static previous lap
Quantity
1
Description
VBOX Touch Unit
1
Advertisement
Table of Contents
Related Manuals for Racelogic RLVBTOUCH-M
Summary of Contents for Racelogic RLVBTOUCH-M
- Page 1 Racelogic product, and offer technical support. Register your device here. What is in the box? When you purchase a VBOX Touch Motorsport V1 (RLVBTOUCH-M), you will find the following items when you open the box: Product Code Quantity...
-
Page 2: Optional Accessories
If you are looking to purchase a new SD card, it is recommended that any card used has a write speed of above 7 MB/s (4 MB/s absolute minimum) and a speed class of 10 (4 absolute minimum). Racelogic recommends SD cards from quality brands such as Transcend, SanDisk, Kingston or Lexar to ensure the best results. - Page 3 SDHC cards (2 GB to 32 GB) Supplied or purchased SDHC cards are formatted in the FAT32 file format. This format is supported by VBOX Touch. SDXC cards (64 GB and above) Purchased SDXC cards will be formatted in exFAT or NTFS file formats; these formats are not supported by VBOX Touch (please reformat as per instructions below).
- Page 4 Logging VBOX Touch logs data via an SD card inserted into the side of the unit. Depending on the Logging Strategy selected within the General Settings area, the unit will either log continuously or when movement is detected (default). Tapping on the SD Card Icon when green...
- Page 5 • Velocity: Velocity in km/h. • Heading: Heading in degrees concerning North. • Height: Height above sea level in meters based on the model of the earth used by VBOX GNSS engines. • Vertical velocity: Vertical velocity in km/h. +ve velocity uphill, -ve velocity downhill. •...
-
Page 6: Satellite Reception
CAN/Serial Right Side The top CAN/Serial port can be used to output serial information, allowing you to either connect VBOX Touch VBOX Test Suite via an RLCAB001 and conduct live testing, or output lap timing parameters. You can find more information about the Serial Output settings here. You can find more detailed connector information on the PIN OUTS page. - Page 7 stable satellite lock (indicated by a flashing red satellite icon), you can use the external antenna (RLACS262) supplied with the unit. IMPORTANT • If you are conducting Brake Trigger Deceleration Tests, you should use the external antenna. • The first time that the unit is used, it may take up to 10–15 minutes to fully acquire satellites. After this, it will usually take 1–2 minutes to acquire satellites.
-
Page 8: Gps Coldstart
Media, iframe, embed and object tags are not supported inside of a PDF. Acquiring Satellite Lock Tall buildings or trees can block GNSS signals, causing a reduction in the number and quality of satellites being tracked, leading to inaccurate position measurements and a noisy velocity signal. GNSS works best in open areas/ Avoid tree-lined roads GPS Coldstart If VBOX Touch is struggling to acquire a satellite lock, a GPS coldstart may be required. - Page 9 When the button has been pressed, the unit will make an audible sound and a ‘PLEASE WAIT’ message will be displayed on the screen which will count down from 3. The number of satellites will then be displayed as '00' and GPS status will show ‘SEARCHING FOR SATELLITES’...
- Page 10 Function Behaviour Colour The current lap is > 5 km/h slower than the reference lap The LEDs will illuminate blue during the process of creating a Reference Lap. When loading a Track Database file, the progress of the track database update is displayed via the LEDs; each lit LED will represent 25% of the process with all LEDs extinguishing when the process is complete.
-
Page 11: Screen Overview
Screen Overview Main screen example Setup 1. Connect the power via the Power socket. 2. Insert the SD card into the Side of the Unit. The SD Card Icon should display as green as long as the card has free space. - Page 12 3. When the unit has booted, select the Mode Button and press LAP TIMING if it is not already selected. 7. Select the Settings Button , then the Lap Timing option and navigate to the Track Settings. The unit will display the currently selected track based on the GPS location.
- Page 13 11. Press the Exit Button to return to the Lap Timing screen. 12. Take the vehicle outside and wait for the VBOX Touch to gain satellite lock. The Satellite Icon should display as solid green. Note: The first time that the unit is used, it may take up to 15 minutes to fully acquire satellites. After this, it will usually take 1 to 2 minutes to acquire satellites.
- Page 14 13. Select which Lap Timing display you would like to be shown (Main or Basic) by selecting the Forward and Back arrows on the bottom right of the screen or by swiping the screen left or right. Main screen Basic screen 14.
- Page 15 Basic Screen: • VBOX Touch will display the current live lap time and when a new lap starts, the previous lap time will be displayed for 3 seconds before reverting to displaying the current live lap time. It is possible to just display the previous lap time by Disabling the Rolling Lap Time.