Related Manuals for Teknik 5427134
Summary of Contents for Teknik 5427134
- Page 1 Teknik For all your newfangled gadgetry. Iron Foundry Double Pedestal Desk Model 5427134...
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-16 Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. TOP (1) DRAWER FRONT (2) BOTTOM (2)
-
Page 4: Table Of Contents
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. (EXTENSION SET SHOWN SEPARATED) EXTENSION RAIL - 4 EXTENSION SLIDE - 4 HIDDEN CAM - 1 ADJUSTABLE CAM SCREW - 1 WOOD DOWEL - 40 GLIDE - 8 APPLIQUE CARD - 1 FILE GLIDE - 4... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty carton to avoid scratching your unit or the fl oor. å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diagram below. Be å...
- Page 6 Step 2 Insert four WOOD DOWELS (5) into a BACK (E). å Push a set of ENDS/UPRIGHTS (C and D) onto the å Some assembly WOOD DOWELS (5) in the BACK (E). (and snacks) required. Insert four WOOD DOWELS (5) into the edges of the å...
-
Page 7: Cam Screw
Hardware Usage Guide HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL NOTE: Various CAM SCREWS or a CAM DOWEL may be used. Turn the CAM SCREW or gently tap the CAM DOWEL until the shoulder is against the surface of the part. -
Page 8: 1-7/8" Hex Head Screw
Step 3 Push a HIDDEN CAM (3) into the MODESTY PANEL (B). å Do not tighten the HIDDEN CAM in this step. Fasten the UPRIGHT FRAMES (R) to the MODESTY å PANEL (B). Tighten four 1-7/8" HEX HEAD SCREWS (11) Arrow using the L-WRENCH (9). - Page 9 Step 4 Fasten the SHORT BRACES (P) to the UPRIGHT å FRAMES (R). Tighten four 1-3/8" HEX HEAD SCREWS (13) using the L-WRENCH (9). Fasten the END FRAMES (Q) to the SHORT BRACES (P). å Tighten four 1-3/8" HEX HEAD SCREWS (13) using the L-WRENCH (9).
- Page 10 Step 5 Fasten the BOTTOMS (O) to the UPRIGHT å FRAMES (R) and END FRAMES (Q). Turn four 1-3/8" Side Step: Make HEX HEAD SCREWS (13) using the L-WRENCH (9). nachos. (Optional, but recommended.) NOTE: Do not completely tighten the 1-3/8" HEX HEAD å...
-
Page 11: 1-3/8" Hex Head Screw
Step 6 Stand your unit upright. å Fasten the CABINET BOTTOMS (F) to the SHORT å BRACES (P). Tunn eight 1-3/8" HEX HEAD SCREWS (13) using the L-WRENCH (9). NOTE: Do not completely tighten the 1-3/8" HEX HEAD å SCREWS at this time. 1-3/8"... - Page 12 Step 7 Turn a CAM SCREW (4) into the TOP (A). å Insert eight WOOD DOWELS (5) into the å END/UPRIGHTS (C and D). Flip the TOP (A) over and fasten it to the å MODESTY PANEL. (B). Tighten the HIDDEN CAM. Fasten the TOP (A) to the å...
-
Page 13: 1-3/16" Flat Head Screw
Step 8 Insert four WOOD DOWELS (5) into a set of DRAWER å SIDES (H and J). Fasten the DRAWER SIDES (H and J) to a DRAWER å BACK (K) and a DRAWER BOX FRONT (L). Use eight 1-3/16" FLAT HEAD SCREWS (15). NOTE: Be sure the WOOD DOWELS in the DRAWER å... - Page 14 Step 9 Flip the drawer over. å If you're doing this to Push a FILE GLIDE (8) onto the top edges of a BACK (K) å help a friend, don't and DRAWER BOX FRONT (L). leave without a bite. Insert four WOOD DOWELS (5) into the edges of the å...
-
Page 15: 1-1/4" Machine Screw
Step 10 Fasten two EXTENSION SLIDES (2) to a set of DRAWER SIDES (H and J). Use six 3/8" å FLAT HEAD SCREWS (16). Fasten a PULL (7) to a DRAWER FRONT (G). Use two 1-1/4" MACHINE SCREWS (14). å Repeat this step. -
Page 16: Adjustable
Step 11 To insert a drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the å unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. - Page 17 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. •...