Related Manuals for Beckhoff CU8810-0010
Summary of Contents for Beckhoff CU8810-0010
- Page 1 Installation- and Operating instructions for CU8810-0010 DVI Splitter for CP29xx-0000, CP39xx-0000, CP69xx-0010 and CP79xx-0010 Version: 1.0 Date: 2023-09-19...
-
Page 3: Table Of Contents
3.3.1 Connecting cables 3.3.2 Connecting Power Supply 4 Operation Configuration 4.1.1 Opening the enclosure 4.1.2 DIP Switch 1 (SW1) 4.1.3 DIP Switch 2 (SW2) 4.1.4 DIP-Switch 3 (SW3) Architecture Description 4.2.1 Version 1 4.2.2 Version 2 4.2.3 Version 3 CU8810-0010... - Page 4 Maintenance Shutting down 4.4.1 Disposal 5 Dimensions 6 Technical Data 7 Appendix Beckhoff Support and Service 7.1.1 Beckhoff branches and partner companies 7.1.2 Beckhoff company headquarters Approvals for USA and Canada FCC Approval for USA FCC Approval for Canada CU8810-0010...
-
Page 5: Foreword
Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG. 1.1.6 Delivery conditions In addition, the general delivery conditions of the company Beckhoff Automation GmbH & Co. KG apply. CU8810-0010... -
Page 6: Description Of Safety Symbols
• the operation manual is in good condition and complete, and always available for reference at the location of the product • none of the safety and warning notes attached to product are removed, and that all notes remain legible. CU8810-0010... -
Page 7: Product Description
A common application in machine and plant construction is the simultaneous display of a PC screen on several monitors. Up to four DVI/USB Control Panels can be connected to a PC via the CU8810-0010 DVI Splitter. Thanks to DVI/USB2.0 extension technology, the Control Panels can each be connected at distances of 50 m from the DVI Splitter. -
Page 8: Connections
A proper ground connection of the device is absolutely necessary for the correct function of the touchscreen. Note 2.2.2 Data Connectors The CU8810-0010 has three kinds of connectors: USB type B, RJ45 and DVI. The pin layouts are described below. 2.2.2.1 USB Typ B Port (X20) (standard cable) Connector USB TYP-B LP-mount. - Page 9 TMDS Data 0 - DDC Clock TMDS Data 0 + DDC Data TMDS Data 0/5 Shield Analog Vertical Sync n.c. TMDS Data 1 - n.c. TMDS Data 1 + TMDS Clock Shield TMDS Data1/3 Shield TMDS Clock + n.c. TMDS Clock - CU8810-0010...
-
Page 10: Led-Diagnostics
15 V supplied to USB/E Port USB/E No suspend Port-2 lights yellow Suspend USB/E No 15 V supplied to USB/E Port Port-3 lights green 15 V supplied to USB/E Port USB/E No suspend Port-3 lights yellow Suspend CU8810-0010... -
Page 11: Installation
4. Please keep the associated paperwork. It contains important information for handling the unit 5. Check the contents for visible shipping damage. If you notice any shipping damage or inconsistencies between the contents and your order, you should notify Beckhoff Service. CU8810-0010... -
Page 12: Mounting / Unmounting
Just push the unit on the lower side under the rail (1) and snap in the upper side (2) as shown below: 3.2.2 Unmounting the DVI Splitter To release the CU8810-0010 from the mounting rail push up the unit (3) and pull off the device from the rail (4):... -
Page 13: Connecting Devices
• Switch off all the devices that are to be connected • Disconnect all the devices that are to be connected from the power supply • Connect all the cables between the CU8810-0010 and the devices that are to be connected • Reconnect all devices to the power supply. -
Page 14: Operation
Operation 4 Operation 4.1 Configuration Front view of the CU8810-0010 with opened enclosure 4.1.1 Opening the enclosure The device is configured by a set of three switches. The switches are covered by an enclosure on the upper right side on the front. To open the enclosure you need to remove the two screws, as shown below: There are three DIP switches and two status LEDs covered by the plate. -
Page 15: Dip Switch 1 (Sw1)
The next switch 3 is used to set the back termination for the output level. The use of back terminations is highly recommended for best signal integrity. Factory Settings This switch is set to off by factory and should only be changed after consultation with the Beckhoff Support. Note CU8810-0010... - Page 16 DVI Output Port 1 (X51) The DDC-channel from DVI Input Port 1 (X41) is connected to DDC-channel to DVI Output Port 2 (X52) The DDC-channel from DVI Input Port 1 (X41) is connected to DDC-channel to DVI Output Port 3 (X53) CU8810-0010...
-
Page 17: Dip Switch 2 (Sw2)
4.1.3 DIP Switch 2 (SW2) This DIP switch block configures the signal parameters for DVI Output Ports. Factory Settings These switches are set as default from factory and should not be changed. Note The default settings are: Switch Setting CU8810-0010... -
Page 18: Dip-Switch 3 (Sw3)
DVI Data Input Select Switch 2 for DVI Output Port 3 (X53) (X53) IN_SELx_high IN_SELx_low Function Disable the DVI Output Port x Select DVI Input Port 1 (X41) for DVI Output Port x Select DVI Input Port 0 (X40) for DVI Output Port x Illegal CU8810-0010... - Page 19 Disable DVI Output Port 0 (X50) Select DVI Input Port 1 (X41) for DVI Output Port 1 (X51) Select DVI Input Port 0 (X40) for DVI Output Port 2 (X52) Select DVI Input Port 0 (X40) for DVI Output Port 3 (X53) CU8810-0010...
-
Page 20: Architecture Description
DVI output. The card has two external DVI ports and enables direct connection of two DVI/USB Control Panels to C5102, C6140, C6150, C6240 or C6250 PCs. Via the CU8810-0010, these two DVI outputs can be branched further to up to four Control Panels. -
Page 21: Version
If a Panel PC with DVI output is used (e.g. “Economy” Panel PC CP62xx), the DVI Splitter can be used to transfer an image that differs from the main image on the Panel PC to up to four Control Panels. In this case commands can also be transferred via USB from the individual Control Panels to the Panel PC. CU8810-0010... -
Page 22: Maintenance
The device can be cleaned with a soft, damp cloth. Do not use any aggressive cleaning materials, thinners, scouring material or hard objects that could cause scratches. 4.3.2 Maintenance The DVI Splitter CU8810-0010 is maintenance-free. 4.4 Shutting down 4.4.1 Disposal Observe national electronics scrap regulations Observe the national electronics scrap regulations when disposing of the device. -
Page 23: Dimensions
The product is characterized by small overall installed size. With a height of approx. 100 mm, the module dimensions exactly match those of the Beckhoff Bus Terminals. Together with the lowered connector surfaces, this means that it can be used in a standard terminal box with a height of 120 mm. -
Page 24: Technical Data
Technical Data 6 Technical Data Product name CU8810-0010 Number of ports 1 USB Typ B port (downstream) 4 USB2.0 Extender Rx ports (RJ45) 2 DVI input ports 4 DVI output ports Supported standard USB 2.0 Supported baud rates 12 Mbit (Full Speed), 1.5 Mbit (Low Speed) -
Page 25: Appendix
Please contact your Beckhoff branch office or partner company for local support and service on Beckhoff products! The contact addresses for your country can be found in the list of Beckhoff branches and partner companies: www.beckhoff.com. You will also find further documentation for Beckhoff components there. -
Page 26: Approvals For Usa And Canada
Technical modifications to the device may cause the loss of the FCC approval. Note 7.4 FCC Approval for Canada FCC: Canadian Notice This equipment does not exceed the Class A limits for radiated emissions as described in the Radio Interference Regulations of the Canadian Department of Communications. CU8810-0010...