Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Raven Spray Air 2010 Predator
Summary of Contents for Raven Spray Air 2010 Predator
- Page 1 Spray Air 2010 Predator...
- Page 3 H A P T E R NTRODUCTION Congratulations on your purchase of the Raven Autoboom system! This system is designed to provide worry-free operation of your hydraulically controlled booms. The following in- structions are designed to assist you in the proper installation of the system hardware. The Autoboom hydraulic installation process is fairly straight forward and prior knowledge of the machine’s hydraulic system is beneficial.
-
Page 4: Basic Kit
Spray Air 2010 Predator Autoboom Installation Manual PowerGlide System Basic Kit w Hardware Installation Kit 117-0230-064 Contents w Hydraulic Hose and Fitting Kit w Hydraulic Valve and Mounting Hardware w Axle Mounting Brackets and Mounting w Axle Kit 117-0131- w 2 Axles... -
Page 5: Installation Safety Requirements
Manual # 016-0230-064 REV A 11/06 H A P T E R AFETY Installation This section is divided between general safety precautions, specific safety mea- sures in respect to the hydraulic and electrical system, and machine driving and Safety operating safety. Requirements Important: The machine must remain stationary and switched... -
Page 6: Electrical Safety Precautions
Spray Air 2010 Predator Autoboom Installation Manual Hydraulic Safety Precautions Important: Sprayer hydraulics are under pressure. Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when first opening a system that was previously pressurized. -
Page 7: Areas Of Operation
The Autoboom must only be used on private property without public access. It must only be used within cleared fields. It must not be used when traveling on any public roads or access ways. Raven Industries advises that users familiarize themselves with Autoboom operation by first reading the Autoboom Installation Manual and the PowerGlide, PowerGlide Plus, or UltraGlide Calibration and Operator’s Manual. - Page 8 Spray Air 2010 Predator Autoboom Installation Manual We welcome your feedback about this manual. If you have any comments or Contacting suggestions for improvement, please let us know by contacting our Customer Raven Support Center by any of the following methods:...
- Page 9 Manual # 016-0230-064 REV A 11/06 OWER LIDE H A P T E R OPULATING AND OUNTING THE ALVE Autoboom Valve FITTING PORT 3/4" JIC (M) to 3/4" SAE O-Ring (M) P (Filter), T 9/16" JIC (M) to 9/16" SAE O-Ring (M) LV, RV, LC, RC 9/16"...
- Page 10 Spray Air 2010 Predator Autoboom Installation Manual Remove cavity plug (5A) and port plug (6A). Power Glide Dual Discard port plug (6A) or keep for future upgrade to Power Glide Plus. Cartridge Option Insert cavity plug from port 5A into port 6A.
- Page 11 Manual # 016-0230-064 REV A 11/06 H A P T E R & F YDRAULIC ITTINGS NSTALLATION ORIENTATION MACHINE AUTOBOOM VALVE HOSE END LOCATION HOSE END LOCATION 214-1000-112 3/4" JIC (F) Pressure Port 3/4" JIC (F) EF (Priority Valve) 214-1000-331 3/4"...
- Page 12 Spray Air 2010 Predator Autoboom Installation Manual Connect priority valve T port, Autoboom valve T port, and machine manifold T port together using supplied hoses and tee fittings. LC, RC, LV, RV Disconnect left and right Up lines from machine manifold and connect to LC (use supplied hose extension) and RC respectively on Autoboom valve.
- Page 13 Manual # 016-0230-064 REV A 11/06 LC, RC, LV, RV Replace 90° fitting on restrictor assemblies. Connect restrictor assemblies to LV and RV ports on Autoboom valve. Connect LV and RV ports to left and right ‘Up’ ports (respectively) on machine manifold using supplied hoses. Load Sense Connect LS port on priority valve to LS2 port on Autoboom valve using supplied hose.
- Page 14 Spray Air 2010 Predator Autoboom Installation Manual Power Glide Hydraulic Schematic...
-
Page 15: Mounting The Valve
Manual # 016-0230-064 REV A 11/06 OWER LIDE & LTRA LIDE H A P T E R OPULATING AND OUNTING THE ALVE Autoboom Valve FITTING PORT 3/4" JIC (M) to 3/4" SAE O-Ring (M) P (Filter), T 9/16" JIC (M) to 9/16" SAE O-Ring (M) LV, RV, LC, RC 9/16"... - Page 16 Spray Air 2010 Predator Autoboom Installation Manual NOTE: Ultra Glide - Make sure floating orifice in LC and RC ports are installed with slot facing out. Mount Autoboom valve on center rack. Mount priorty valve on center rack to the right...
- Page 17 Manual # 016-0230-064 REV A 11/06 H A P T E R & F YDRAULIC ITTING NSTALLATION ORIENTATION MACHINE AUTOBOOM VALVE HOSE END LOCATION HOSE END LOCATION 214-1000-112 3/4" JIC (F) Pressure Port 3/4" JIC (F) EF (Priority Valve) 214-1000-331 3/4"...
- Page 18 Spray Air 2010 Predator Autoboom Installation Manual Connect priority valve T port, Autoboom valve T port, and machine manifold T port together using supplied hoses and tee fittings. LC, RC, LV, RV Disconnect left and right Up lines from machine manifold and connect to LC (use supplied hose extension) and RC respectively on Autoboom valve.
- Page 19 Manual # 016-0230-064 REV A 11/06 Replace 90° fitting on restrictor assemblies. Connect restrictor assemblies to LV and RV ports on Autoboom valve. Connect LV and RV ports to left and right ‘Up’ ports (respectively) on machine manifold using supplied hoses. Load Sense Connect LS port on priority valve to LS2 port on Autoboom valve using supplied hose.
- Page 20 Spray Air 2010 Predator Autoboom Installation Manual Power Glide Plus & Ultra Glide Hydraulic Schematic...
-
Page 21: Wheel & Sensor
Manual # 016-0230-064 REV A 11/06 H A P T E R & S HEEL ENSOR OUNTING Wheel Mounting Mount axle receiver bracket just inside first boom fold. -
Page 22: Sensor Mounting
Spray Air 2010 Predator Autoboom Installation Manual Sensor Mounting Mount sensor near boom tip. -
Page 23: Wiring Harness
Manual # 016-0230-064 REV A 11/06 H A P T E R & W ONTROLLER IRING ARNESS Use the following diagrams to install the wiring harness. Be sure to allow enough slack in harness when racking booms. Connect power leads to battery. - Page 24 Spray Air 2010 Predator Autoboom Installation Manual Power Glide...
- Page 25 Manual # 016-0230-064 REV A 11/06 Power Glide Plus...
- Page 26 Spray Air 2010 Predator Autoboom Installation Manual Ultra Glide...
-
Page 27: Replacement Parts
Manual # 016-0230-064 REV A 11/06 P P E N D I X EPLACEMENT ARTS On the following pages you will find replacement part diagrams and listings for Power Glide, Power Glide Plus, and Ultra Guide systems. Please refer to these diagrams when calling to request replacement parts. - Page 28 Spray Air 2010 Predator Autoboom Installation Manual Valve Blocks Power Glide Valve Block Replacement Parts Drawing Power Glide Plus Valve Block Replacement Parts Drawing...
- Page 29 Manual # 016-0230-064 REV A 11/06 Ultra Glide Valve Block Replacement Parts Drawing...
- Page 30 Spray Air 2010 Predator Autoboom Installation Manual Wheel Assembly and Machine Specific Wheel and Bracket Drawing Brackets Cushioned Axle Replacement Parts Drawing...
- Page 31 Manual # 016-0230-064 REV A 11/06 Sensor and Brackets Machine Specific Sensor U-Bolt Drawing Molded Sensor Replacement Parts Drawing...
- Page 32 Spray Air 2010 Predator Autoboom Installation Manual NOTES:...
- Page 35 RAVEN INDUSTRIES LIMITED WARRANTY WHAT IS COVERED? This warranty covers all defects in workmanship or materials in your Raven Flow Control Product under normal use, maintenance, and service. HOW LONG IS THE COVERAGE PERIOD? This warranty coverage runs for 12 months from the purchase date of your Raven Flow Control Product.
- Page 36 P.O. Box 5107 www.ravenprecision.com Sioux Falls, SD 57117-5107 fcdinfo@ravenind.com Notice: This document and the information provided are the property of Raven Industries, Inc. and may only be used as authorized by Raven Industries, Inc. All rights reserved under the copyright laws.