Off-site transport....................18 6.2.1 Transport space ..................18 6.2.2 Legislation ....................18 6.2.3 Qualification of the staff ................19 6.2.4 Warning of residual risks ................. 19 Water management system C 400 V 2 from 40 Original operating instructions Version 2...
Page 3
11.2 Water management system C 400 V Type 558 with positive locking ....33 11.3 Water management system C 400 V type 562 with 2 wastewater pumps ..... 34 12 Circuit diagrams ......................35 12.1 Water management system C 400 V Type 557 ............ 35 12.2...
Page 4
Table of contents 16 EC Declaration of Conformity ..................40 Water management system C 400 V 4 from 40 Original operating instructions Version 2...
Product and manufacturer Product and manufacturer Product This operating manual describes the following product: Water management system C 400 V. Serial number: Manufacturer Name and address deconta GmbH Im Geer 20 46419 Isselburg Phone 02874/9156-0 02874/9156-11 E-mail info@deconta.com Internet www.deconta.com...
The operator keeps these operating instructions or extracts thereof within easy reach in the immediate vicinity of the machine. When handing over the machine to another person, the operator passes these operating instructions on to that person. Water management system C 400 V 6 from 40 Original operating instructions Version 2...
Description of the possible consequences for humans, animals and the environment that may occur as a result of the hazard. Escape Recommendations for action on how to avoid hazards Water management system C 400 V 7 from 40 Original operating instructions Version 2...
The following table gives an overview of the instruction signs used and their meaning. Symbol Meaning Symbol Meaning Wear safety shoes Use protective clothing Use hearing protection Water management system C 400 V 8 from 40 Original operating instructions Version 2...
3.1.2 Version with 2 waste water pumps The Water management system C 400 V can be equipped with a second waste water pump. This sucks the contaminated shower water through a separate pre-filter in parallel with the first waste water pump and then pumps it through the two common fine filters. A typical application is a 5-chamber airlock with two shower chambers.
- Functional safety of safety-related electrical, electronic and programmable electronic control systems. Scope of delivery The delivery scope of the machine includes the following items: ▪ Water management system C 400 V ▪ Filters ▪ Service Pack ▪...
Product waste: Geka connection for filtered wastewater into the sewerage system ▪ Product material feed: Geka connection for contaminated shower water ▪ Product floor: castor wheels Water management system C 400 V 11 from 40 Original operating instructions Version 2...
The following accessories are optionally available for Water management system: Designation Item no. Illustration Waste water hose 5m with Geka BU1504 connection 3/4". Fresh water hose 5m with Geka BU1504a connection 1/2". Water management system C 400 V 12 from 40 Original operating instructions Version 2...
Normal operation At a distance of 1m from the unit: 65 dB (A) ▪ Short-time with active signal horn: 92 dB (A) Wear hearing protection in the immediate vicinity of the Water management system. Water management system C 400 V 13 from 40 Original operating instructions Version 2...
For this reason, persons leaving the construction area via airlocks must shower when exiting. The deconta Water management system heats the shower water and treats (filters) the contaminated wastewater. The electronic flow heater, the wastewater pump and a 3-stage wastewater filter system are accommodated in the powder-coated aluminium housing.
Operating the machine in a technically unsound condition, not being aware of safety and hazards and not observing all instructions in the documentation. Use in potentially explosive atmospheres Water management system C 400 V 15 from 40 Original operating instructions...
Qualified waste management Disposer Dispose of machine company for legally compliant, proper and professional disposal of the machine Water management system C 400 V 16 from 40 Original operating instructions Version 2...
Instruction of persons with regard to protective devices and supplementary protective devices Instruction of persons with regard to residual risks This list is not exhaustive and does not claim to be complete. Water management system C 400 V 17 from 40 Original operating instructions Version 2...
6.2.2 Legislation Off-site transport of the machine shall be in accordance with the legislation of the country in which the machine is transported off-site. Water management system C 400 V 18 from 40 Original operating instructions Version 2...
6.3.3 Warning of residual risks Crushing hazard: Wear safety shoes to protect against running over limbs. Water management system C 400 V 19 from 40 Original operating instructions Version 2...
Falling of the machine may be possible due to unintentional change of position when loading and unloading onto / from a means of transportation. Water management system C 400 V 20 from 40 Original operating instructions Version 2...
The Water management system is delivered ready for operation ex works and is intended for immediate commissioning. If there is visible damage, do not operate the unit. Contact deconta GmbH immediately. Put into operation This section contains information on commissioning the machine.
Fill wastewater pump with water • Fill the filter housing of the 220µ filter with water. • Hand-tighten the union nuts of the filter housings • Establish power connection Water management system C 400 V 22 from 40 Original operating instructions Version 2...
Wastewater IN 1 Wastewater OUT Wastewater IN 2 Cold water Shower 1 Hot water Shower 1 Cold water Shower 2 Hot water Shower 2 Water inlet Water management system C 400 V 23 from 40 Original operating instructions Version 2...
Page 24
Fill wastewater pump with water • Fill the filter housing of the 220µ filters with water • Hand-tighten the union nuts of the filter housings • Establish power connection Water management system C 400 V 24 from 40 Original operating instructions Version 2...
After approx. 5 seconds, switch to the "Automatic" position, the positive locking is now activated, the green buttons on the door boxes remain lit. Water management system C 400 V 25 from 40 Original operating instructions...
Preset temperature (approx. 37°C). Do not change the settings on the temperature setting knob of the instantaneous water heater. Danger of scalding! Check the outlet temperature before every shower! Temperature setting knob Water management system C 400 V 26 from 40 Original operating instructions Version 2...
One person is needed to use the machine. Tools needed No tools are needed to use the machine. Required equipment No equipment is needed to use the machine. Water management system C 400 V 27 from 40 Original operating instructions Version 2...
(3) Use a screwdriver to press on the pressure point of the limiter (see picture) until it engages. (4) If necessary, put the potentiometer back on and attach the cover. (5) Switch on the mains voltage. Water management system C 400 V 28 from 40 Original operating instructions...
Change filters only when the unit is switched off. Only use approved filters. Pull out the mains plug before opening the housing Water management system C 400 V 29 from 40 Original operating instructions Version 2...
Remove dirty filters when damp to prevent the release of filter dust. ▪ Only use approved filters ▪ Damaged filter cartridges must not be used Union nut Pressure gauge Filter monitoring Filter head spanner Water management system C 400 V 30 from 40 Original operating instructions Version 2...
Page 31
Repairs and maintenance work may only be carried out in compliance with all relevant safety measures. The filters must be disposed of in accordance with the legal requirements. Water management system C 400 V 31 from 40 Original operating instructions Version 2...
If this is not possible, the alternative spare parts should correspond to the characteristics of the original spare parts in order to ensure the safe, trouble-free and economical use of the machine. 11.1 Water management system C 400 V Type 557 Water management system C 400 V 32 from 40 Original operating instructions...
Spare parts 11.2 Water management system C 400 V Type 558 with positive locking Water management system C 400 V 33 from 40 Original operating instructions Version 2...
Spare parts 11.3 Water management system C 400 V type 562 with 2 wastewater pumps Water management system C 400 V 34 from 40 Original operating instructions Version 2...
Circuit diagrams Circuit diagrams 12.1 Water management system C 400 V Type 557 Water management system C 400 V 35 from 40 Original operating instructions Version 2...
Circuit diagrams 12.2 Water management system C 400 V type 558 with forced locking Water management system C 400 V 36 from 40 Original operating instructions Version 2...
Circuit diagrams 12.3 Water management system C 400 V type 562 with 2 wastewater pumps Water management system C 400 V 37 from 40 Original operating instructions Version 2...
The optional hoses may only be stored completely emptied and in a hygienic condition! During storage, make sure that contamination with other substances is excluded. Drinking water hoses (fresh water hoses) and waste water hoses must be stored separately. Water management system C 400 V 38 from 40 Original operating instructions...
15.3 Waste The waste generated by the machine must be disposed of in a legally compliant, proper and professional manner. Water management system C 400 V 39 from 40 Original operating instructions Version 2...
Safety of machinery - Safety distances to prevent hazard zones from being reached by the upper and lower limbs (ISO 13857:2019) Name and address of the person authorised to compile the technical file: Boland, Thomas - deconta GmbH, Im Geer 20 - 46419 Isselburg Place: IsselburgDate : 27.04.2023...