ENGLISH
To switch the unit on, press and hold down
–
the button (3).
Use this operation mode for combined pro-
–
cessing of liquid and solid foodstuffs.
Notes:
Products should be put into the bowl before
–
the unit is switched on. The amount of prod-
ucts to be processed should not exceed 2/3
of the capacity of the bowl in which they are
processed.
Before starting to chop/mix, we recommend
–
to peel fruit, remove inedible parts, such
as stones, and cut fruit into cubes approxi-
mately 2х2 cm in size.
After you finish using the unit, take the power
–
plug out of the mains socket and remove the
detachable blender attachment (1), turning
it counterclockwise (pic. 1).
ATTENTION!
Do not remove the blender attachment (1)
–
during operation.
To avoid damaging the blades, do not pro-
–
cess too hard products such as cereals,
rice, spices, coffee beans, hard cheeses,
frozen products etc.
If the foodstuffs are hard to chop with the
–
blender attachment (1), add some liquid if
possible.
USING THE WHISK ATTACHMENT
Use the whisk attachment (9) only for beating
cream and egg whites, making biscuit dough or
for mixing ready desserts.
WARNING: Before installing the whisk (9) and
the gear (8), make sure that the power plug is
not inserted into the mains socket.
Insert the whisk attachment (9) into the
•
whisk gear (8) (pic. 2).
Insert the whisk gear (8) into the motor
•
unit (2) and turn it clockwise, make sure that
the gear (8) and the whisk (9) are fixed prop-
erly (pic. 3).
•
Insert the power plug into the mains socket.
•
Immerse the whisk (9) into the bowl with
food.
Note: You can put the foodstuffs into the
cup (10).
To switch the unit on, press and hold down
•
the button (3).
After you finish using the unit, take the power
•
plug out of the mains socket, disconnect
the whisk gear (8) from the motor unit (2)
by turning the gear (8) counterclockwise
(pic. 3).
Remove the whisk (9) from the gear (8)
•
(pic. 2).
ATTENTION!
Do not use the whisk attachment (9) to
–
knead tight dough.
Put products into the bowl before switching
–
the unit on.
USING THE CHOPPER
The chopper is used to chop meat, cheese,
onion, herbs, garlic, carrots, walnuts, almonds,
prunes, vegetables and fruit.
ATTENTION!
Do not chop very hard products, such as ice
cubes, frozen products, nutmegs, coffee beans,
cereals etc.
Before you start chopping:
Cut meat, cheese, onions, vegetables or fruit
–
into pieces approximately 2x2 cm in size.
Remove stems of herbs, shell nuts.
–
Remove bones, sinews and cartilage from
–
meat.
Chopping
Caution: the blades of the chopping knife (7) are
very sharp!
Always hold the chopping knife (7) by the upper
plastic end.
•
Place the chopper bowl (6) on a flat stable
surface.
•
Set the chopping knife (7) on the axis inside
the chopper bowl (6).
Put the products into the chopper bowl (6).
•
Note: Do not switch the unit on when the chop-
per bowl (6) is empty.
Place the geared lid (5) on the chopper
•
bowl (6) and turn it clockwise as far as it will
go (pic. 4).
•
Install the motor unit (2) on the geared
lid (5) feeding chute, turn the motor unit (2)
counterclockwise as far as it will go, make
sure that the motor unit (2) is fixed properly
(pic. 5).
Install the motor unit (2) strictly in the vertical
•
position and evenly.
To connect the unit to the mains, insert the
–
power cord plug into the mains socket.
To switch the unit on, press and hold down
–
the button (3).
12