Table of Contents
Advertisement
Quick Links
P P P P P P
P P
P
P P
PECO
PECO
PECO
PECO
PECO
36
793603
793605
MANUAL PART#: Q0573
R
R R
Estate Series
Cu. Ft.
Briggs & Stratton 6.5 HP Vanguard
Briggs & Stratton 14 HP Vanguard
OPERATOR'S MANUAL
ASSEMBLY
ESTATE SERIES/PASTURE VAC
COLLECTION SYSTEM
Unassembled
693603U
Engine Driven 36 Cu. Ft.
OPERATION
36
Pasture Vac
Cu. Ft.
703602
Briggs & Stratton 6.5 HP Vanguard
703604
Briggs & Stratton 14 HP Vanguard
MAINTENANCE
Rev.1.2 - May 2022
Advertisement
Table of Contents
Related Manuals for Peco Estate 793603
Summary of Contents for Peco Estate 793603
- Page 1 P P P P P P ESTATE SERIES/PASTURE VAC PECO PECO PECO PECO PECO COLLECTION SYSTEM Estate Series Pasture Vac Cu. Ft. Cu. Ft. 793603 703602 Briggs & Stratton 6.5 HP Vanguard Briggs & Stratton 6.5 HP Vanguard 793605 703604 Briggs &...
-
Page 2: Table Of Contents
GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Engine Installation - - - - - - - - - - - - - - - - - - - - - - - 22 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - 3 Tongue Assembly Installation - - - - - - - - - - - - - - - - 22... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
6. REMEDIED EXCLUSIVE: The only remedies the purchaser has in connection with the breach or performance of any warranty on New PECO, Inc. consumer products are set forth above. In no event will New PECO, Inc. be liable for special incidental or consequential damages. -
Page 5: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION Introduction Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf. -
Page 6: Installation For Use
Section II - INSTALLATION FOR USE Tilt Base Frame Assembly Installation To install the Tilt Base Frame Assembly (Item #2), position the Tilt Base Frame Assy between the Chassis Frame Assembly (Item #1) and use (1) Tilt Rod (Item #3) to mount the Tilt Base Frame Assy. Secure the Tilt Rod by using (1) 3/4”... -
Page 7: Latch Assembly Installation
Latch Assembly Installation Before installing the Latch Assembly (Item #1), position the (2) Bearing Block / Sets (Item #3) over the Latch Assy and make sure that (1) Bearing Block / Set is set between and resting on the washers of the Latch Assy, refer to Figure B. Position the pre-assembled parts under the Box Frame Assembly (Item #2) aligning the bolt holes of the Bearing Block / Sets to those of the Box Frame Assy, Refer to Figure A and Figure C. -
Page 8: Box Bottom & Front Panel Installation
Box Bottom & Front Panel Installation Set the Bottom Panel (Item #2) onto the Box Frame Assembly (Item #1) aligning the mount holes of the Bottom Panel to those of the Box Frame Assy, refer to Figure A. Next, Position the Front Panel (Item #3) upright and on top of the Bottom Panel. -
Page 9: Box Side Panel Installation
Box Side Panel Installation Place (1) Box Side Panel (Item #1) on either side of the Front Panel. Make sure the Side Panel is on the inside of the Front Panel and Bottom Panel. Align all mount holes of these parts. When securing the right Side Panel along the upright side with the Front Panel, use (3) 5/16”-18 x 1/2”... -
Page 10: Door Rail Assembly Installation
Door Rail Assembly Installation Position the Right Door Rail Assembly (Item #1) onto the right Side Panel aligning all bolt holes to those of the Side Panel. For this step, the top (2) bolt holes will remain open and not use any hardware. Secure the Right Vertical Rail Assy relatively loose by using (4) 5/16”-18 x 3/4”... -
Page 11: Support Rail Installation
Support Rail Installation Position the Side Support Rail (Item #1) over the Door Rail Assembly and Side Panel aligning the bolt holes of these parts. Refer to Figure A. Secure the Side Support Rail relatively loose by using (2) 5/16”-18 x 3/4” Carriage Bolts (Item #2) on the middle and bottom mount holes of the Support Rail, (1) 5/16”-18 x 1”... -
Page 12: Screen Frame Assembly Installation
Screen Frame Assembly Installation Before Installing the Screen Frame Assembly (Item #1), place (4) Large Tinnerman Clips (Item #6) over the (4) mount holes on the front of the Screen Frame Assembly. Remove and set aside the top set of hardware, (1) 5/16”-18 x 1” Carriage Bolt and (1) 5/16”-18 Flange Nuts, securing the Door Rail / Side Support Rail on both sides from the previous step as well. -
Page 13: Box Top Panel Installation
Box Top Panel Installation Start by placing (11) Small Tinnerman Clips (Item #4) along the top of the Side Panels (Item #2) and Front Panel (Item #3), see Figure A. Secure the Top Panel (Item #1) over the Front Panel and Side Panel by using (8) Tinnerman Screws (Item #4) along the sides of the Top Panel. -
Page 14: Inlet Cone Installation
Inlet Cone Installation Position the Inlet Cone (Item #1) over the collection hole of the Front Panel and secure the Inlet Cone by using (3) Blunt Tip Screw (Item #3) and (3) Flat Tinnerman Nuts (Item #2). Note: Some parts and part features have been hidden from view for visual clarity. Figure A Front Panel Inlet Cone... -
Page 15: Door & Hinge Assembly Installation
Door & Hinge Assembly Installation Position Door & Hinge Assy (Item #1) back behind the trailer, see Figure A. Align the Door Hinge and insert the Door Hinge into the tabs of the Left and Right Door Rails (Item #2 & #3) on both sides. See Figure B. Note: Some parts and part features have been hidden from view for visual clarity. -
Page 16: Door Tension Rod Assembly Installation
Door Tension Rod Assembly Installation Slide the Door Tension Rod Assembly (Item #1) in through the Angle Support Bracket of the lower side of the trailer assembly, refer to Figure B. Next, install (1) Pivot Rod Strap (Item #2) onto the Door Tension Rod Assemblies (Item #1) by pre-threading (1) 1/2”-13 Flange Nut (Item #3) onto the Door Tension Rod. -
Page 17: Latch Rod Assembly Installation
Latch Rod Assembly Installation The following instructions are for the installation of the Latch Rod Assembly to the Right side of your collection unit. The instructions for the Left side is identical to those shown. To install the Latch Rod Assembly (Item #1), first loosely install the Latch Rod Assy to the Right Latch Release Lever (Item #2) by using (2) 1/2”-13 Flange Nuts (Item #3). -
Page 18: Inlet Arm Assembly Installation
Inlet Arm Assembly Installation Position the Inlet Arm Assembly (Item #1) and Foam Seal (Item #2) into the Inlet Cone as shown in Figure A. Place the Inlet Arm Assy over the Chassis Frame Assembly’s (Item #3) Inlet Mount Plate, see Figure A and Figure B. Secure the Inlet Arm Assy by using (2) 3/8”-16 x 1”... -
Page 19: Tongue Assembly Installation
Tongue Assembly Installation Estate Series Unit Instructions Position the Tongue Assembly (Item #1) between the Tongue Support Bracket of the 50 Trailer Assembly (Item #2) aligning the bolt holes of both parts. Secure the Tongue Assy by using (3) 1/2”-13 x 3-1/2” HHCS (Item #3) and (3) 1/2”-13 Flange Nuts (Item #4). -
Page 20: Engine Mount Assembly Installation
Engine Mount Assembly Installation Estate Series Unit Instructions Position the Tongue Assembly (Item #1) between the Tongue Support Bracket of the 50 Trailer Assembly (Item #2) aligning the bolt holes of both parts. Secure the Tongue Assy by using (3) 1/2”-13 x 3-1/2” HHCS (Item #3) and (3) 1/2”-13 Flange Nuts (Item #4). -
Page 21: Ball Clevis Assembly Installation
Ball Clevis Assembly Installation Estate Series Unit Instructions Note: The Ball Clevis Assembly (Item #3) will need to be secured onto the rear of your tractor. This may require you to drill a hole in your bumper to procure the securement. You’ll need to first position the Ball Clevis Assembly and mark where it’ll best fit your tractor. -
Page 22: Engine Installation
Engine Installation First, place (2) Rubber Shock Absorber (Item #3) on top of the Engine Mount Assembly (Item #2) aligning the bolt holes. Next, position the Engine Assembly (Item #1) on top of the Shock Absorbers aligning the bolt holes of all the parts. -
Page 23: Hose Hanger Installation
Hose Hanger Installation Pasture Vac Unit Instructions Place the Hose Hanger (Item #1) into the mount hole of the Tongue Assembly (Item #2), see Figure B. Secure the Hose Hanger by using (1) Clamp Plate (Item #3) and (1) 1/2”-13 Flange Nut (Item #4). Once secured, close the top end of the Hose Hanger using (1) Tube Cap (Item #5). -
Page 24: Universal Battery Kit Installation
Universal Battery Kit Installation Pasture Vac Unit Instructions Your Universal Battery Box (Item #1) will need to be assembled before installing the Universal Battery Kit P#(A2326). First, make sure your screw holes on each tab are aligned with the holes of the base part. Then, using a 1/4”-20 x 1/2” Slotted Hex Washer Head Thread Cutting Screw (Item #2), screw in the sheet metal screw to secure each tab. - Page 25 Universal Battery Kit Installation (Cont.) Position the Battery Box (Item #2) over the Rubber Shock Absorber (Item #5) and over the Engine Mount Plate of the Tongue Assembly (Item #1). Secure the Battery Box by using (2) 5/16”-18 x 3/4” HHCS (Item #6) and (2) 5/16”-18 Ny- Flange Lock Nuts (item #7).
-
Page 26: Wiring Kit Installation
Wiring Harness Installation To connect the Wiring Kit (P#A2152), connect the 4 gage Red Wire (P#P0620) to the positive (+) terminal of the starter solenoid on the engine. Route the Red Wire from the solenoid to the positive (+) terminal of the battery. Connect the 4 gage Black Wire (P#P0621) to one of the mounting bolt holes located on the bottom of the engine. - Page 27 Wiring Harness Installation (Cont.) HARNESS #:P0620 RED (4 AWG) w/ 5/16” RING TERMINAL FROM BATTERY POSITIVE “+” TO STARTER SOLENOID “+” HARNESS #:P0621 BLACK (8 AWG) w/ 5/16” RING TERMINAL FROM BATTERY NEGATIVE “-” TO ENGINE BLOCK “-” P#:P0076 5/16” BATTERY RING TERMINAL Pasture Vac Units - Universal Battery Kit P#(A2326) HARNESS #:P0278 RED (10 AWG) w/ 5/16”...
-
Page 28: Impeller Blade Removal/Replacement
Impeller Blade Removal/Replacement To Remove: First remove the 3/8”-24 x 1” GR8 HHCS P#(K0003) (#1), 3/8” Double Indented Washer P#(K0284) (#2) and (1) Tapered Washer P#(K0277) (#3) from the Taper-Lock Bushing P#(S4302) (#5). Next remove the (2) 1/4”-20 x 1” HHCS P#(K1225) (#4) and place them into the threaded holes of the Taper-Lock Bushing (#5). Gradually thread each bolt evenly into the Taper-Lock Bushing, forcing the blade to break-away from the Taper-Lock Bushing. -
Page 29: Hose Guard Installation
Hose Guard Installation For Briggs & Stratton - 14HP Vanguard Engine Option Your Engine Drive will require a Hose Guard (Item #1) to be installed, this will prevent any heat transfer from the engine exhaust to the Upper Hose. To install the Hose Guard, align the bolt holes of the Hose Guard (Item #1) to those located on the Blower Housing, refer to Figure A. -
Page 30: Length Of Hose Adjustment
Length Of Hose Adjustment The hoses in the following steps must be cut to fit your machine. Do not cut the hoses until you have tried to fit them on your machine. Remember that the hoses need to be long enough to allow for the opening and closing of the collection system as well as allowing ample clamping surface between each component. -
Page 31: Wand Kit Installation
Wand Kit Installation Pasture Vac Unit Instructions Install one end of the 6” Hose over the Blower Cone (Item #1) by using (1) 6” Hose Clamp (Item #2). Secure the other end over the Nose Cone of the Wand Kit by using (1) 6” Hose Clamp (Item #2). Refer to Figure A. Once installed, the 6”... -
Page 32: Exploded Views & Parts List
ES36 Estate Series ES36P Pasture Vac... - Page 33 A1862 36 Trailer Vac Exploded View...
- Page 34 A1862 36 Trailer Vac Exploded Parts List...
- Page 35 A0969 Door & Hinge Assembly Explosion...
- Page 36 A0949 Door Assembly Explosion...
- Page 37 A1861 Wand Kit / Large Explosion...
- Page 38 A1861 Wand Kit / Large Exploded Parts List...
-
Page 46: Safety Decals
SAFETY DECALS To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. P P P PECO... -
Page 47: Operating Instructions
Correct any deficiency before continuing operation. 5. Check for wear or deterioration of the upper or lower hoses. If there are any portions of the hose that have been torn or worn through, replace with genuine PECO parts. 2020 (v1.0) -
Page 48: Parts And Service
If for any reason your Service Center manufacturers to be affixed to the component. is unable to service your collection system or supply replacement parts, contact New PECO, Inc. and include the following information on the chart below. DOCUMENT THE FOLLOWING INFORMATION FOR FUTURE REFERENCE... -
Page 50: Troubleshooting
Troubleshooting 2017 (v1.0) Collection System Performance Problem Possible Cause Corrective Action — Cutting blades are bent or — Install new cutting blade unbalanced — Loose blower pulley or pulley Abnormal Vibration — Tighten the pulley assembly — Contact dealer to replace —... - Page 51 Notes...
- Page 52 Additional Options A2276 - Trailer Tow Kit The Trailer Tow Kit P#(A2276) is designed to allow your Trailer Vac Unit to be moved and maneuvered around easily without a tractor creating a stand alone unit. This will also allow for an easy storage or transportation of your Trailer Vac Unit when not being used.
- Page 53 Notes...
- Page 54 P P P P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...