Subscribe to Our Youtube Channel
Related Manuals for Glow Bricks The Lord of the Rings Rivendell
Summary of Contents for Glow Bricks The Lord of the Rings Rivendell
- Page 2 Firstly, separate the lighting parts as follows and differentiate as A/B/C Split the whole model as 3 parts to assemble them with the lights The shown part would be done with Part A...
- Page 3 Detach the trees and the pavilion first Take the top of the entrance out, replace the flames on both side by the lighting parts, make sure following the position same as the picture below...
- Page 4 Restore the entrance, assemble the two flames on the fireplace, remove the shown parts to place the remain lighting parts into the house Restore the parts from previous step, leave the parts out inside the red circle and place the wire in between the flame and lantern on the slot. Then restore the part and place the lantern on it...
- Page 5 Restore the dark grey tiles to cover the wires properly Replace another lantern inside...
- Page 6 Remove the top of the bridge then assemble the 1x4 lighting plate on it and put it back on the bridge The 2pcs of 1x3 lighting plates would be assembled under the pavilion...
- Page 7 For the remain lights, the blue lighting plates would be moved to the river later Now we can deal with the 3pcs of 1x3 lighting plates first, remove the top of the pavilion and some parts of the base on the side to move the lights to the top...
- Page 8 Assemble the plates at the pavilion Restore the pavilion and the side, place the wires around the pole nicely...
- Page 9 Lift up the pavilion and place the lighting blue plates to the water side The connector could be left here Assemble the first two plates as shown...
- Page 10 Remove the curved clear blue part to take the remain lights onto the river Then assemble them on the river evenly...
- Page 11 Now put the trees back on the model, connect the lighting round plates with the connectors besides the lantern and the flame at the entrance Then assemble the lighting round plates on the tree rancomly...
- Page 12 Now it’s turn for Part B Detach the top to assemble with the shown part...
- Page 13 Detach the bottom, assemble the 1x4 lighting plates at the bottom and move the remain parts by the gap in betweeen...
- Page 14 Split the top as shown, restore them partially and move the remain lights on top The wires could be hidden by the parts...
- Page 16 At last, assemble the dark grey 1x3 lighting plate, move the lighting round plate and assemble it on the top...
- Page 17 Remove the statues and the shelve first...
- Page 18 Assemble the 2pcs of tan lighting plates and the white 1x2 magnetic brick as shown Detach the building to assemble the led bars...
- Page 19 Stick the led bar on the brick Restore the removed parts and stick the leds one by one...
- Page 21 Put the statues back after the led’s are sticked then restore the whole building Replace the candle flames at downstairs...
- Page 22 Remove the plate on the second floor to move the remain lights to upstairs The green lighting round plates should be moved outside to assemble on the side...
- Page 23 Move these lighting parts to second floor Assemble the lighting plates as shown...
- Page 24 The 2 connected flame with black wire would be assembled inside and the one with white wires for the candle beside the bed...
- Page 25 Put the top back and connect the plugs then this part would be finished...
- Page 26 Now it’s turn for Part C Take the tree down, assemble by the green lighting round plates...
- Page 27 Put the tree back and the connector would be facing the building Get the lighting parts main body, connect with the green lighting round plates...
- Page 28 Assemble the white lighting plate next to the plug inside the building Remove the top and the tiles shown to move the led bar and yellow round plate to it...
- Page 29 Move the lights to the top and stable by restoring the tiles removed in last step Remove some parts from the top...
- Page 30 Put the bottom part back on the model first Place the led bar as shown and restore the bricks...
- Page 31 Then assemble the lighting yellow round plate Assemble the white lighting plate followed by the one at page 28...
- Page 32 Then assemble the grey lighting 1x6 plate at the shown spot There’re still 2pcs of 1x4 grey lighting plates followed by the previous step Remove the roof of both sides first...
- Page 33 Remove the tile located in the red circle, assemble one 1x4 lighting plate on one side Then assemble the other side...
- Page 34 Put the slides with lighting plates back on the building then restore the tile afterwards Follow by the step on page 31, assemble the other two white lighting plates...
- Page 35 Leave the connector here and gonna connect with the other lighting parts later Move the remain lighting parts and install them at downstairs Start from assemble the 1x4 in red circle...
- Page 36 Move the lighting plate inside and assemble it as shown The 1x2 white brick follow by the last step would be moved to 2 floor and place on the corner...
- Page 37 Then assemble the remain three lighting plates...
- Page 38 Use the lighting flames attached by the lighting plates to replace the candle flames There’re exact amount of flames at the corresponding position...
- Page 39 Now assemble the last lighting parts Replace the 2x2 tan tile on top by the lighting part, then put the ring back on it...
- Page 40 Take the connector at the end and connect the plugs on the side Assemble the green lighting round plates on the grasses The yellow round plate connect to the ring would be assembled in the red circle...
- Page 41 Move the rest of the lighting round plates to the tree and assemble them on it Detach the top to assemble with the shown part...
- Page 42 To power up, connect the USB cable to the power source Take the building from the previous part and combine them together Make sure the magnet in the 1x2 bricks get contacted to transmit the power...
- Page 43 Then the other side would be lighted up as well At last, take the connector from Part A to connect with the USB cable and the whole set would now be lighted up...
Need help?
Do you have a question about the The Lord of the Rings Rivendell and is the answer not in the manual?
Questions and answers