Advertisement
Quick Links
Advertisement
Related Manuals for Glow Bricks Avengers Tower
Summary of Contents for Glow Bricks Avengers Tower
- Page 1 Avengers Tower...
- Page 2 Before the installation, we need to detach the whole tower by each floor...
- Page 3 Remove the shown parts from both sides of the tower Remove the tiles from the side, you may just remove the one shown in the pictures below because these are placed right on the crossline of each floor...
- Page 4 Remove the tiles at the shown lines which are the crosslines of each floor Now you can start splitting the tower, start from the top remove the shown sections...
- Page 5 Remove the A sign’s and the shown part Then take the liquor shelf and the light grey parts from out side...
- Page 6 Remove the shown windows after the parts from previous step are taken away Remove the shown plates at the corners then you can unlock the hold for this floor...
- Page 7 You can now lift up this floor after unlocking The floors below would be much easier, just use the separator to split them...
- Page 8 For the other side, assemble the grey lighting plate Place the divided floors properly, and you are now prepared to start installing the lights...
- Page 9 3 floors starting from the bottom would be assembled with lighting part A Get the third floor which is the Ironman’s lab, remove the shown parts...
- Page 10 Get the led bulb at the end and put it inside the arc reactor from the back of the shelf Stable the wire by the grey plate at bottom, then stick the led bars on the floor...
- Page 11 Restore the stand for Ironman suit, the connector would be placed between the poles and the remain lighting parts would be moved to the floors below Get the floor below and take the 1x8 light grey plates from the shown spot...
- Page 12 Assemble the light grey lighting plates follow by the stand for Ironman suit Detach the shown parts and get the remain lighting parts through...
- Page 13 Take the clear blue object out and place the led bulb inside of it, also the orange lighting round plate Place the part from previous step back to the building then restore the top side of this floor...
- Page 14 Assemble the dark grey lighting plates then restore the bottom of this floor Combine the building with the 1 floor and place the USB cable out from the back door...
- Page 15 Take lighting part B to assemble it to the shown floor Start from the bottom by the 1x6 lighting plates with connector attached...
- Page 16 Put floor back on top and connect the plugs Take the cage away and remove the yellow 1x2 plates out from there...
- Page 17 Assemble the 1x2 lighting plates by the shown way and the black 1x3 inside the cage Get the third floor which is the Ironman’s lab, remove the shown parts At last, place the led bulbs inside the red tiles at front...
- Page 18 Put the cage back with the crossbeam removed Leave the light grey lighting plate above the cage and the rest outside the crossbeam...
- Page 19 Assemble all three of the lighting plates, the wire connecting both of the dark grey lighting plates can be hidden under the tile shown in red circle Get the lighting part C1 with the longest wire with connect and connect them...
- Page 20 Put it along to the highest floor and assemble the 1x10 lighting plate to the crossbeam Get the third floor which is the Ironman’s lab, remove the shown parts Be noted the wire can be hidden under the plates at the corner...
- Page 21 Make sure all the lights above are installed properly then restore the floors at the back and don’t forget the lock, then place the led bulb inside the lamp After that restore the windows at the back, place two connectors to outside of the tower...
- Page 22 Then stable the wires by the blue plates Turn around the model and restore the level above it, place the longest wire with the remain lighting parts in between the studs as shown...
- Page 23 The two 1x4 lighting plates from previous step would be assembled now Restore the pole to stable the wire...
- Page 24 Assemble the 1x4 lighting plates as shown Then pull the remain lighting parts to the top...
- Page 25 Assemble all the remain lighting parts at the top Take lighting part C2 stick and connect them...
- Page 26 Put the covers on then it’s done Now get the shorter led strips to stick around the A sign (note it has to be started on the top of the “A” so that the connector would be placed right on the top)
- Page 27 Connect the plugs then put the signs back and hide the connectors behind the letter Restore the curved light grey and the tiles on the side...
- Page 28 Stick the longer led strips on the curved light grey tiles on both side Connect the plugs then restore the long tile at the middle...
- Page 29 Restore all the tiles removed then the installation for the tower is done Then take lighting part D for the jet...
- Page 30 Remove the parts from the back Replace the clear blue 1x2 plate by the lighting plate connect with orange round plates then replace the 1x2 blue plate besides the green round tile...
- Page 31 Assemble the orange round plates on the back then restore the parts Place the led bulb under the green round tile...
- Page 32 Pass the remain lighting parts at the bottom Assemble the 1x2 lighting plate at the pilot seat...
- Page 33 Then pass to the end and replace the 1x2 plate Same as the previous, place the led below the red round tile...
- Page 34 The installation for the jet is done You may choose to place the jet outside the tower, connect with the USB cable sharing with the lamppost...
- Page 35 Or put it inside the tower, there’s a spare connector for it...
Need help?
Do you have a question about the Avengers Tower and is the answer not in the manual?
Questions and answers