Foster 7300000 Use And Installation Manual page 7

CONNECTION TO THE POWER SUPPLY
CONNECTION TO THE POWER SUPPLY
Installation diagram
Model Supply Voltage / Frequency Number of phases
7380645
Installation diagram
Installation diagram
7381645
7381245
7382645
Model Supply Voltage / Frequency Number of phases
7380645
Model Supply Voltage / Frequency Number of phases
7380645
7383645
7300000
7384645
7381645
7381245
7382645
7381645
7381245
7382645
7383645
7384645
7383645
7384645
In order to make a fixed connection to the mains, insert an all-pole circuit breaker

between the appliance and the mains. This device shall have a contact separation in all
poles, providing full disconnection under overvoltage category III conditions.
The current conducting and isolated parts must be protected from any possibility of direct

contact.
The appliance may ONLY be connected by an authorized qualified technician.

Before any intervention, disconnect the appliance from the power mains. Connect the

Electric system protection should comply with all relevant regulations.

appliance in compliance with the electric connections diagram supplied; make sure the
The connection clips can be accessed when the connection clip covers are opened /

relevant network voltage is observed!
removed.
The appliance may ONLY be connected by an authorized qualified technician.
The ground wire should be connected to the clip indicated by the earth symbol.


Before connecting the appliance, make sure the voltage indicated on the rating plate is
Electric system protection should comply with all relevant regulations.

The mains cable should be fed through the fastening clip which protects it from being


consistent with the voltage in your home network. Connection voltage should be checked
The connection clips can be accessed when the connection clip covers are opened /
accidentally pulled out.

by a qualified technician using a corresponding measuring device!
removed.
After connecting the appliance, turn on all cooking zones / heaters for approximately

The rating plate with basic information is attached on the lower side of the appliance.
Before connecting the appliance, make sure the voltage indicated on the rating plate is

three minutes to make sure they are operating correctly.

In order to make a fixed connection to the mains, insert an all-pole circuit breaker
consistent with the voltage in your home network. Connection voltage should be checked

Incorrect connection may destroy parts of the appliance, making the warranty void!

between the appliance and the mains. This device shall have a contact separation in all
by a qualified technician using a corresponding measuring device!
Connection cable on the back of the appliance should be led in such way that it DOES

poles, providing full disconnection under overvoltage category III conditions.
The rating plate with basic information is attached on the lower side of the appliance.
NOT touch the appliance back wall, as this part will get very hot during operation.

The current conducting and isolated parts must be protected from any possibility of direct
In order to make a fixed connection to the mains, insert an all-pole circuit breaker

The appliance is generally configured to the maximum available power, shown in the


contact.
between the appliance and the mains. This device shall have a contact separation in all
technical data table. It's possible to set an operating mode with power limitation. This
Before any intervention, disconnect the appliance from the power mains. Connect the
poles, providing full disconnection under overvoltage category III conditions.

setting can be made at the time of installation or subsequently by a specialized
appliance in compliance with the electric connections diagram supplied; make sure the
The current conducting and isolated parts must be protected from any possibility of direct
technician. See chapter on power limitation setting.

relevant network voltage is observed!
contact.
The ground wire should be connected to the clip indicated by the earth symbol.
Before any intervention, disconnect the appliance from the power mains. Connect the


The mains cable should be fed through the fastening clip which protects it from being
Use cables type: H05V2V2-F
appliance in compliance with the electric connections diagram supplied; make sure the

accidentally pulled out.
relevant network voltage is observed!
After connecting the appliance, turn on all cooking zones / heaters for approximately
The ground wire should be connected to the clip indicated by the earth symbol.

LIVE L1 – L2 – L3

three minutes to make sure they are operating correctly.
The mains cable should be fed through the fastening clip which protects it from being

EARTH
Incorrect connection may destroy parts of the appliance, making the warranty void!
accidentally pulled out.

Connection cable on the back of the appliance should be led in such way that it DOES
NEUTRAL N1 – N2
After connecting the appliance, turn on all cooking zones / heaters for approximately


NOT touch the appliance back wall, as this part will get very hot during operation.
three minutes to make sure they are operating correctly.
The appliance is generally configured to the maximum available power, shown in the
Incorrect connection may destroy parts of the appliance, making the warranty void!


technical data table. It's possible to set an operating mode with power limitation. This
Connection cable on the back of the appliance should be led in such way that it DOES

setting can be made at the time of installation or subsequently by a specialized
NOT touch the appliance back wall, as this part will get very hot during operation.
220-240 V~ 50/60 Hz
technician. See chapter on power limitation setting.
The appliance is generally configured to the maximum available power, shown in the

technical data table. It's possible to set an operating mode with power limitation. This
setting can be made at the time of installation or subsequently by a specialized
Use cables type: H05V2V2-F
technician. See chapter on power limitation setting.
LIVE L1 – L2 – L3
220-240 V~ 50/60 Hz
Use cables type: H05V2V2-F
EARTH
NEUTRAL N1 – N2
LIVE L1 – L2 – L3
EARTH
380-415 V ~ 50/60 Hz
NEUTRAL N1 – N2
technical customer documentation
220-240 V~ 50/60 Hz
company: 0083 / E.G.O. Germany (E.G.O. Elektro-Gerätebau GmbH)
220-240 V~ 50/60 Hz 220-240 V~ 50/60 Hz
4.2.6 Shortcut switch OFF pot
220-240 V~ 50/60 Hz
To be able to switch off a pot really fast the user can double tab on the required pot. The power leve
immediately switched to power level 0.
380-415 V ~ 50/60 Hz 220-240 V~ 50/60 Hz
380-415 V ~ 50/60 Hz
380-415 V ~ 50/60 Hz
220-240 V~ 50/60 Hz
220-240 V~ 50/60 Hz
380-415 V ~ 50/60 Hz
 Double tap on pot icon
380-415 V ~ 50/60 Hz
 Pot is selected and is then switched OFF.
technical customer documentation
4.2.7 Power level slider
The slider provides a convenient way of setting the power level.
company: 0083 / E.G.O. Germany (E.G.O. Elektro-Gerätebau GmbH)
BROWN – BLACK - GREY
GREEN / YELLOW
BLUE
Power cable section
1 phase + N 3 x 2,5 mm2
BROWN – BLACK - GREY
1 phase + N 3 x 4 mm2
GREEN / YELLOW
BLUE
BROWN – BLACK - GREY
Power cable section
GREEN / YELLOW
2 phases + N 4 x 2,5 mm2
BLUE
1 phase + N 3 x 2,5 mm2
Power cable section
1 phase + N 1 phase + N 5 x 2,5 mm2 3 x 2,5 mm2
1 phase + N 3 x 4 mm2
3 phases + N 1 phase + N 5 x 1,5 mm2 3 x 4 mm2
2 phases + N 4 x 2,5 mm2
25
2 phases + N 4 x 2,5 mm2
1 phase + N 5 x 2,5 mm2
1 phase + N 5 x 2,5 mm2
3 phases + N 5 x 1,5 mm2
3 phases + N 5 x 1,5 mm2
25
5
25
Connection
Connection
Connection
1 2 3 4 5
5
1 2 3 4 5