Dear client, Thank you for having chosen our induction ceramic hob. In order to make the best use of your appliance, we would advise you to read carefully the following notes and to keep them for a later consulting. SUMMARY SAFETY.............................
SAFETY Precautions before using Unpack all the materials. The installation and connecting of the appliance have to be done by approved specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors. To be used, the appliance must be well-equipped and installed in a kitchen unit and an adapted and approved work surface.
Precautions not to damage the appliance Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage the ceramic glass. Sand or other abrasive materials may damage ceramic glass. Avoid dropping objects, even little ones, on the vitroceramic. ...
DESCRIPTION OF THE APPLIANCE Technical data Type Total Power Position Nominal Power* Booster Power* Diameter 3000W Front 2300W 3000W 250 mm 7321240 Front left 1200W 1400W 160 mm 3400W 7322240 Rear right 2300W 3000W 200 mm * The given power may change according to the dimensions and material of the pan. Control panel Control light timer Locking key...
Display Display Designation Function Zero The heating zone is activated 1…9 Power level Selection of the cooking level Pan Detection No pan or inadequate pan Error message Electronic failure Residual heat The heating zone is hot Booster The boosted power is activated Ventilation The cooling system is fully automatic.
Timer The timer is able to be used simultaneous with all 2 heating zones and this with different time settings (from 0 to 99 minutes) for each heating zone. Setting and modification of the cooking time Action Control panel Display To select the heating zone Press key [ + ] or [ - ]...
COOKING ADVICES Pan quality Adapted materials : steel, enamelled steel, cast iron, ferromagnetic stainless-steel, aluminium with ferromagnetic bottom. Not adapted materials : aluminium and stainless-steel without ferromagnetic bottom, cupper, brass, glass, ceramic, porcelain. The manufacturers specify if their products are compatible induction. To check if pans are compatibles: ...
WHAT TO DO IN CASE OF A PROBLEM The symbol [ E 4 ] displays : The hob must be configured according to the following procedure. I) Warning : before starting all pots must be removed from the cooktop. II) Disconnect the cooktop from the main supply : remove fuse or disconnect circuit breaker.
The symbol [ U ] displays There is no pan on the cooking zone. The pan is not compatible with induction. The bottom diameter of the pan is too small. The symbol [ C ] or [ E ] displays ...
INSTALLATION INSTRUCTIONS The installation comes under the exclusive responsibility of specialists. The installer is held to respect the legislation and the standards enforce in his home country. How to stick the gasket The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. His installation has to be done carefully, in conformity of the following drawing.
ELECTRICAL CONNECTION The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously. Protection against the parts under tension must be ensured after the building-in. ...
Page 15
Dear client, Thank you for having chosen our induction ceramic hob. In order to make the best use of your appliance, we would advise you to read carefully the following notes and to keep them for a later consulting. SUMMARY SAFETY............................
SAFETY Precautions before using Unpack all the materials. The installation and connecting of the appliance have to be done by approved specialists. The manufacturer can not be responsible for damage caused by building-in or connecting errors. To be used, the appliance must be well-equipped and installed in a kitchen unit and an adapted and approved work surface.
Precautions not to damage the appliance Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage the ceramic glass. Sand or other abrasive materials may damage ceramic glass. Avoid dropping objects, even little ones, on the vitroceramic. ...
DESCRIPTION OF THE APPLIANCE Technical data Type Total Power Position Nominal Power* Booster Power* Diameter Front 1200W 1400W 150 mm 3700W 7322230 Rear 2000W 2300W 220 mm * The given power may change according to the dimensions and material of the pan. Control panel Control light timer Locking key...
Display Display Designation Function Zero The heating zone is activated 1…9 Power level Selection of the cooking level Pan Detection No pan or inadequate pan Error message Electronic failure Residual heat The heating zone is hot Booster The boosted power is activated Ventilation The cooling system is fully automatic.
Starting-up You must first start-up the hob, then the heating zone : Start-up/ switch off the hob : Action Control panel Display To start Press key [ 0/I ] 2 x [ 0 ] To stop Press key [ 0/I ] nothing or [ H ] ...
Power management : The cooking hob is equipped with a power limiting system. When the booster function is activated, and not to exceed the maximum power, the electronic system orders to reduce automatically the power level of an other heating zone. The display is blinking on [ 9 ] during a few seconds and then shows the maximum of power allowed.
Control panel locking To avoid modifying a setting of cooking zones , in particular with within the framework of cleaning the control panel can be locked (with exception to the On/Off key [ 0/I ]). Locking Action Control panel Display Start Press key [ 0/I ]...
Examples of power setting (The values below are indicative) 1 to 2 Melting Sauces, butter, chocolate, gelatine Reheating Dishes prepared beforehand 2 to 3 Simmering Rice, pudding, sugar syrop Defrosting Dried vegetables, fish, frozen products 3 to 4 Steam Vegetables, fish, meat 4 to 5 Water Steamed potatoes, soups, pasta,...
Page 24
3) The left display shows alternatively a [ C ] and a [ 0 ] 4) Press the key lock until both displays indicate either [ C ] or [ - ]. 5) Take your fingers away from the keys and press again the [ - ] key during a few seconds until some [ E ] appear.
MAINTENANCE AND CLEANING Switch-off the appliance before cleaning. Do not clean the hob if the glass is too hot: risk of burn. Remove light marks with a damp cloth with cleaning liquid diluted in a little water. Then rinse with cold water and dry the surface thoroughly. ...
INSTALLATION INSTRUCTIONS The installation comes under the exclusive responsibility of specialists. The installer is held to respect the legislation and the standards enforce in his home country. How to stick the gasket The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. His installation has to be done carefully, in conformity of the following drawing.
ELECTRICAL CONNECTION The installation of this appliance and the connection to the electrical network should be entrusted only to a professionally trained and authorized eletrician, and performed in full respect of all enforced regulations. Protection against the parts under tension must be ensured after the building-in. ...