Spray Gun; Pressure Relief Procedure - WAGNER 2371053 Translation Of The Original Operating Instructions

DE EN
1. Stir the material thoroughly and dilute it in the container as per the recommended dilution (an agitator is recommended for
stirring).
Sprayed material
Glazes
Wood preservatives containing solvents or based on water, mordants, oils, disinfection agents, plant
protective agents
Paints containing solvents and watersoluble paints, primers, vehicle coating paints, thick-film glazes
Interior wall paint (dispersions and latex paint)
The values in the table are reference values. The values in the table are reference values.
i
Find out how much the paint needs to be thinned by testing it. Details on how to test the spray paint can be found Find out how much the paint needs to be thinned by testing it. Details on how to test the spray paint can be found
in the section called "Spray Technique". in the section called "Spray Technique".
Assembly
1. 1. Place both doors / flaps in the storage compartment. Place both doors / flaps in the storage compartment.
2. 2. Insert the handle as shown in the picture and secure it by pushing downwards. (Fig. 2) Insert the handle as shown in the picture and secure it by pushing downwards. (Fig. 2)
3. 3. Remove the protective covers on the hose and hose connection. (Fig. 3) Remove the protective covers on the hose and hose connection. (Fig. 3)
4. Place the spray gun against the tapered end of the hose (Fig. 4, 1) and twist the gun onto the hose. Firmly tighten the thread
using a wrench (13).
5. Twist the thread at the other end of the hose onto the hose connection.
Using a wrench (16), hold the hose connection firmly and tighten the hose with another wrench (17). (Fig. 5)
6. Slide the suction hose onto the inlet valve. Secure with the clamp. (Fig. 6)
7. Press the return hose onto the return hose fitting. Secure with the clamp. (Fig. 7)
Control elements on the device (Fig. 8) Control elements on the device (Fig. 8)
A
The pressure of the spray is set by the pressure regulator.
The correct spray pressure depends on the paint being used.
The device is switched off if the pressure regulator is in position 0.
B
The following settings can be made with the selector switch:
PRIME (Switch set vertically)
SPRAY (Switch set horizontally)

Spray Gun

Always lock the trigger off when attaching the spray nozzle or when the spray gun is not in use.
Danger
•
Fold the trigger lock downwards to lock the trigger (Fig. 9, A).
•
Fold the trigger lock upwards to unlock the trigger (Fig. 9, B).
Another nozzle size and gun filter must be used, depending on the material to be processed.
i
Thin materials:
Thick materials:

Pressure Relief Procedure

Be sure to follow the Pressure Relief Procedure when shutting the unit off for any purpose.
This procedure relieves the pressure from the spray hose and the gun.
Danger
1. 1. Secure the spray gun. (Fig. 9, A) Secure the spray gun. (Fig. 9, A)
2. Switch the device off (pressure regulator in position 0).
Turn the switch into the PRIME position (vertical). (Fig.
3. 3. Release the spray gun. Hold the spray gun over an empty container and press the trigger to relieve the pressure. Release the spray gun. Hold the spray gun over an empty container and press the trigger to relieve the pressure.
4. Secure the spray gun. Secure the spray gun.
22
Thinning recommendation
•
For prefilling the system with paint

•
For pressure relief
•
For using the spray gun

Nozzle 311

Nozzle 517/619

(Fig. 10)
Filter red
Filter white
Control Pro 250 M / 275 M
undiluted
undiluted
dilute by 5 - 10 %
dilute by 0-10 %