Set (Personal Setup) - emitor COMBOLOOK Color Manual

L. L. L. L. Set (Personal Set Set (Personal Set- - - - up): Set (Personal Set Set (Personal Set
Color
The COMBOLOOK COMBOLOOK
COMBOLOOK COMBOLOOK
measurements.
This kind of set-up is performed under the menu (# 6) “SET”
The following parameters may be defined and adjusted: The following parameters may be defined and adjusted:
The following parameters may be defined and adjusted: The following parameters may be defined and adjusted:
Button # 1: Button # 1: ”Vid BW” (Video Bandwidth filter) ”Vid BW” (Video Bandwidth filter): : : :
Button # 1: Button # 1: ”Vid BW” (Video Bandwidth filter) ”Vid BW” (Video Bandwidth filter)
Video filter
The
and is used in conjunction with various resolutions within a specified
bandwidth.
The resolution of details on a
relation to the narrowing of a filter (
The different Video filters
or 100 Hz. or 100 Hz.
or 100 Hz. or 100 Hz.
Button # 2: ”Res BW” (Resolution Bandwidth): Button # 2: ”Res BW” (Resolution Bandwidth):
Button # 2: Button # 2: ”Res BW” (Resolution Bandwidth): ”Res BW” (Resolution Bandwidth):
The resolution bandwidth shows the incoming signal
chip-set in the instrument. Choose between the
wider 1 MHz
mode.
Button # 3: Button # 3: ”P ”P ”P ”P- - - - insert” (Power Insert): insert” (Power Insert):
Button # 3: Button # 3: insert” (Power Insert): insert” (Power Insert):
This function is used for powering external, active accessories (
antenna amplifiers
The output voltage may be adjusted between 12 - 24 volt DC and is
connected via the BNC-connector.
The selected output voltage selected output voltage is selected output voltage selected output voltage
display (next to the battery-symbol).
The default setting of “P “P “P “P – – – – insert”
Warning ! Warning !
Warning ! Warning !
connected equipment not intended to accept/receive voltage!!!! connected equipment not intended to accept/receive voltage!!!! connected equipment not intended to accept/receive voltage!!!! connected equipment not intended to accept/receive voltage!!!!
Button # 4: Button # 4: Set up, with sub Button # 4: Button # 4: Set up, with sub Set up, with sub Set up, with sub- - - - menu
Button # 1 Button # 1 Button # 1 Button # 1
Button # 2 Button # 2
Button # 2 Button # 2
Button # 3 Button # 3 Button # 3 Button # 3
quickly the instrument “scans” a certain frequency range.
Off Off Off Off.
Sub Sub- - - - menu 2; Gr menu 2; Grat.
Sub Sub menu 2; Gr menu 2; Gr
out easier to view, under some circumstances. Default setting is Off.
Sub Sub- - - - menu 3; Units, menu 3; Units, choose between the signal-level values/readouts of
Sub Sub menu 3; Units, menu 3; Units,
dBuV, dBm or dBmV dBuV, dBm or dBmV dBuV, dBm or dBmV dBuV, dBm or dBmV
Sub Sub- - - - menu 4 menu 4; TV level,
Sub Sub menu 4 menu 4
video-presentation
Button # 4 Button # 4 Button # 4: : : : Button # 4
instrument’s serial number, date of manufacturing, software-version etc.
Button # 5 Button # 5 Button # 5 Button # 5: : : :
up): up): up):
may be set-up to individually-defined parameters for specific
after after after after
is placed
signal-carrier
Video filters are: auto Video filters Video filters
resolution. The instrument is normally working in the ”auto
) which require a power-source in order to operate.
insert” insert” is “Off insert”
Mis- - - - use of this function may cause irreparable damage to all Mis use of this function may cause irreparable damage to all
Mis Mis use of this function may cause irreparable damage to all use of this function may cause irreparable damage to all
menu menu: menu
: : : : LCD LCD LCD –Contrast and “Backlite” On/Off can be adjusted. LCD
: Screen Screen- - - - saver saver On/Off. Default setting is On.
Screen Screen saver saver
: Display Display and Sub Display Display Sub Sub Sub- - - - menu 1, S menu 1, S menu 1, S menu 1, S- - - - cursor
grating
at. ( ) shows a grating-net which may make the read-
at. at.
TV level, the level which the
TV level, TV level,
should be between 53-63 dB
(
Version. Version. Specific manufacturing info/data concerning this Version. Version.
CH CH- - - - Table CH CH Table Table Table. Choose between different channel-plans.
SET” SET” in the SET”
the measuring chip-set in the instrument,
is progressively refined in
sweep-time is increased
default
auto auto- - - - mode auto mode mode ( mode ), 100 kHz
narrow 300 kHz
always always always always
visible in upper-left-hand of the LCD-
Off Off” (0 volt). Off
Scan-cursor
cursor ( cursor cursor
automatic attenuation
Main-Menu
.
).
100 kHz 100 kHz, 10 kHz 100 kHz 10 kHz, 1 kHz 10 kHz 10 kHz 1 kHz 1 kHz 1 kHz
before before before before
the measuring
or the
auto” auto auto
such as
). Indicates how
Default setting is
Off. Off. Off.
uses for the
).
28