About This Manual; 1: Terms Used In This Manual; Compatible Products - Honeywell SILENT KNIGHT 6700 Manual

Introduction

1.2 About this Manual

This manual is intended to be a complete reference for all installation and operation tasks for the 6700.
1.2.1 Terms Used in this Manual
The following terminology is used with the 6700 system:
Term
SLC
Module
Input Point
Input Zone
Output Point (or Output Circuit)
Group (or "Output Group")
Output (or "Cadence") Pattern
Mapping
Common Communication Link
SWIFT

1.3 Compatible Products

The chart below lists the products available for use with the 6700.
Type of Device
SK Addressable SLC Devices For a list of compatible devices, refer to the SLC Wiring Manual, P/N: LS10179-000SK-E.
SD Addressable SLC Devices
SWIFT Wireless SLC Devices For a list of compatible devices, refer to the SWIFT Manual, P/N: LS10036-000SK-E.
Other Modules
10
Signaling Line Circuit
The term module is used for all hardware devices except for SLC addressable devices and notification
appliances. This includes the 6700 panel itself.
An addressable sensing device, such as a smoke or heat detector or a contact monitor device.
A protected area made up of input points.
A notification point or circuit for notification appliances. Relay circuits and auxiliary power circuits are also
considered output points.
A group of output points. Operating characteristics are common to all output points in the group.
The pattern that the output will use, for example, Constant, March Code, ANSI 3.41. Applies to zones
and special system events. See Appendix D for additional information.
Mapping is the process of specifying which outputs are activated when certain events occur in the
system. Figure 7.2 describes mapping in detail.
Up to 17 panels can be linked. Consist of any combination of 17 panels of these model numbers: 6700,
6808, 6820 / 6820EVS. For reporting purposes only. Not a peer-to-peer networked system.
Smart Wireless Integrated Fire Technology
Model
5824 Serial/Parallel Allows a printer to be attached for the on-site event logging. Maximum of four 5824s per
Printer Interface Module control panel.
5895XL Power Supply Provides additional power, six Flexput circuits, and two Form C relays. Max 8 per system. See
5895XL Installation Manual (PN 151142) for more information.
5496 NAC Expander Provides 4 additional Notification Appliance Circuits/Auxiliary power. (Up to 8 per 6700
System).
6855 and 5860 LCD 4 x20 Remote LCD annunciator. Can be used in any combination, up to a total of 8 devices on
Annunciator one panel.
6860LCD Annunciator 4 x 40 Remote LCD annunciator can be used in any combination, up to a total of 8 devices on
one panel.
5865-3 and LED annunciator can display up to 30 LEDs (15 red and 15 yellow). 5865-4 has key switches
5865-4 LED for silence and reset, and a system trouble LED. 5865-3, 5865-4, and 5880 can be used in
Annunciator any combination, up to a total of eight devices on one panel.
RA-100TR Trim Ring Trim ring kit for surface mounting the 6860/6855 annunciators.
5860TG and 5860TR Trim ring kits for surface mounting the 5860/5860R annunciator. 5860TG is gray; 5860TR is
Trim Rings red.
5880 LED Driver Driver for up to 40 LEDs. Interfaces with customized annunciator boards. In addition the 5880
Module has eight generic switch input points.
5883 General Purpose Provides 10 Form C relays. Designed to be driven by the 5880. Up to four, 5883s can be used
Relay Module with each 5880 module.
SK-NIC Network Interface Card
SK-FML Fiber-Optic Multi Mode
SK-FSL Fiber-Optic Single Mode
Table 1.2 6700 Compatible Products
Description
Table 1.1 Manual Terminology
6700 Manual — P/N LS10148-001SK-E:F 8/29/2022
Description
About this Manual